• International Journal of Concrete Structures and Materials
• /
• v.4 no.2
• /
• pp.89-96
• /
• 2010

This paper focuses on the effect of creep on the critical compressive strain (CCS) of concrete. The strain of concrete corresponding to the peak compressive stress is crucial in the selection of the ultimate yield strength of the reinforcing bar used in reinforced concrete columns. Among the various influencing factors, such as the creep, shrinkage, loading rate and confinement, the effect of creep and shrinkage is the most significant. So far, investigations into how these factors can affect the CCS of concrete have been rare. Therefore, to investigate the effect of creep and shrinkage on CCS, an experimental (part I) and a parametric study (part II) were conducted, as presented in these papers (part I considers creep effect, part II considers effect of creep and shrinkage). In part I, experiments pertaining to the loading age, loading rate, loading duration and loading and creep levels were conducted to study the effect of these variables on the CCS of concrete. It was found that the effects of the loading rate, loading age, and level and duration on the CCS of concrete were negligible. However, it is very important to consider the effect of creep.

• Nuclear Engineering and Technology
• /
• v.48 no.6
• /
• pp.1376-1386
• /
• 2016

This study investigated the loading rate effect on the fracture resistance under cyclic loading conditions to understand clearly the fracture behavior of piping materials under seismic conditions. J-R fracture toughness tests were conducted under monotonic and cyclic loading conditions at various displacement rates at room temperature and the operating temperature of nuclear power plants (i.e., $316^{\circ}C$). SA508 Gr.1a low-alloy steel and SA312 TP316 stainless steel piping materials were used for the tests. The fracture resistance under a reversible cyclic load was considerably lower than that under monotonic load regardless of test temperature, material, and loading rate. Under both cyclic and monotonic loading conditions, the fracture behavior of SA312 TP316 stainless steel was independent of the loading rate at both room temperature and $316^{\circ}C$. For SA508 Gr.1a lowalloy steel, the loading rate effect on the fracture behavior was appreciable at $316^{\circ}C$ under cyclic and monotonic loading conditions. However, the loading rate effect diminished when the cyclic load ratio of the load (R) was -1. Thus, it was recognized that the fracture behavior of piping materials, including seismic loading characteristics, can be evaluated when tested under a cyclic load of R = -1 at a quasistatic loading rate.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.214-219
• /
• 2004

Crack tip behavior of single mode loading condition(mode I)depend on tensile loading component but one of mixed mode loading condition(mode I+II) have influenced on shear loading component like the practical structure. Because crack closure is caused by shear loading component under mixed-mode loading a research on the behavior in the stage of crack initiation and propagation require to be evaluate about crack closure effect by fatigue crack surface friction. For that reasion we examined the behavior at the crack tip by direct measuring method. Measured behavior at the crack tip was analyzed through vector crack tip displacement. As a result, crack propafation equation was corrected by considering with crack closure effect. In addition we compared fatigue fracture crack surface and crack closure level.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1994.10a
• /
• pp.55-60
• /
• 1994

The paper is aimed at investigating the buckling strength of single-layer latticed domes with the geometrically initial imperfection under the uniformly distributed vertical-loading and the partially concentrated equipment-loading. The results show that the effect of initial imperfection on the buckling strength, if the magnitude of equipment-loading is small, is much more sensitive in domes of overall buckling than in domes of member buckling, but with increasing equipment-loading, it is very sensitive both in domes of overall buckling and of member buckling

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1992.10a
• /
• pp.127-132
• /
• 1992

The effect of 5 typical rise ratio(h/a=2/9, 5/18, l/3, l/2, 2/3) on the buckling characteristics of single-layer latticed domes with rectangular network under the external pressure are the theoretically studied on the basis of geometically nonlinear FEM and shell analogy method. The loading conditions are 4 types, that is, 1) the uniform pressure loading 2)the uniform snow loading 3) the half - sided asymmetric pressure loading 4) the half - sided asymmetric snow loading.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.348-353
• /
• 1996

This study addresses the evaluation of the durability of reinforced concrete marine structures subjected to fatigue loading. The laboratory investigation was carried out on full and half size reinforced concrete specimens with three different water cement ratios (0.3, 0.4, and 0.56), static and fatigue loading conditions, and epoxy-coated and regular black steel reinforcements. The marine tidal zone was simulated by alternate filling and draining of the tank (wet and dry cycled), and a galvanostatic corrosion technique to accelerate corrosion of reinforcement was used. Half-cell potentials and changes of crack width were measured periodically during the exposure and followed by ultimate strength testing. The significant findings include adverse effect of fatigue loading, existence of an explicit size effect, poor performance of epoxy coated steel, and negative effect of increasing water/cement ratio.

• Steel and Composite Structures
• /
• v.1 no.2
• /
• pp.201-212
• /
• 2001

In order to investigate the effect of the loading rate on the mechanical behavior of SRC shearwalls, we conducted the lateral loading tests on the 1/3 scale model shearwalls whose edge columns were reinforced by H-shaped steel. The specimens were subjected to the reversed cyclic lateral load under a variable axial load. The two types of loading rate, 0.01 cm/sec for the static loading and 1 cm/sec for the dynamic loading were adopted. The failure mode in all specimens was the sliding shear of the in-filled wall panel. The edge columns did not fail in shear. The initial lateral stiffness and lateral load carrying capacity of the shearwalls subjected to the dynamic loading were about 10% larger than those subjected to the static loading. The effects of the arrangement of the H-shaped steel on the lateral load carrying capacity and the lateral load-displacement hysteresis response were not significant.

• Structural Engineering and Mechanics
• /
• v.85 no.5
• /
• pp.665-677
• /
• 2023

In the present study, the limit point buckling and postbuckling behaviors of sinusoidal, shallow arches with pinned supports subjected to localized sinusoidal loading, based on the Euler-Bernoulli beam theory, are numerically analyzed. There are some studies on the buckling of sinusoidal shallow arches under the effect of sinusoidal loading. However, in these studies, the sinusoidal loading acts along the horizontal projection of the entire shallow arch. No study has been found in the relevant literature pertaining to the stability of the shallow arches subjected to various lengths of sinusoidal loading. Therefore, the purpose of this paper is to contribute to the literature by examining the effect of the length of the localized sinusoidal loading and the initial rise of the shallow arch on the limit point buckling and postbuckling behaviors. Equilibrium paths corresponding to certain values of the length of the localized sinusoidal loading and various values of the initial rise parameter are presented. It has been observed that the length of the sinusoidal loading and the initial rise parameter affects the transition from no buckling to limit point instability remarkably. The deformed configurations of the sinusoidal shallow arch under localized loading regarding buckling and postbuckling states are illustrated, as well. The effects of the length of the localized sinusoidal loading on the internal forces of the shallow arch are investigated during various stages of the loading.

• Earthquakes and Structures
• /
• v.5 no.2
• /
• pp.239-259
• /
• 2013

Typically, beams that form part of structural systems are subjected to vertical distributed loading along their length. Distributed loading affects moment and shear distribution, and consequently spread of inelasticity, along the beam length. However, the finite element models developed so far for seismic analysis of frame structures either ignore the effect of vertical distributed loading on spread of inelasticity or consider it in an approximate manner. In this paper, a beam-type finite element is developed, which is capable of considering accurately the effect of uniform distributed loading on spreading of inelastic deformations along the beam length. The proposed model consists of two gradual spread inelasticity sub-elements accounting explicitly for inelastic flexural and shear response. Following this approach, the effect of distributed loading on spreading of inelastic flexural and shear deformations is properly taken into account. The finite element is implemented in the seismic analysis of plane frame structures with beam members controlled either by flexure or shear. It is shown that to obtain accurate results the influence of distributed beam loading on spreading of inelastic deformations should be taken into account in the inelastic seismic analysis of frame structures.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.62-68
• /
• 2012

This study was carried out to evaluate the effect of PCC loading at thick stock on the physical properties of paper. The effect of starch addition(2, 4 and 6%) and mixing time(5, 10 and 20 min.) on the filler retention and paper properties were investigated. Optimum dosage of cationic starch as a fixing agent was 4%, and mixing time did not showed any significant effect on the filler retention. PCC loading at thick stock was more effective to improve bulk and opacity than PCC loading at thin stock, although their improvement was not so significant. It was also found that the strength properties could be improved by the loading at thick stock. PCC loading method at thick stock could be considered as one of potential approaches for further improving of paper properties, although further research works are required in order to apply the PCC loading at thick stock in the paper mill.