• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.303-306
• /
• 2008

This study proposes an essential process of type certificate, which is load comparison for proving the calculated design load. The load measurement was carried out according to IEC 61400-13 standard and the load calculation was performed with same condition using FLEX 5 code. For more accurate load simulation, the controller parameter of original model at the design stage was modified to site optimized value and some node points are added to coincidence with measurement. The load comparison was performed with various wind parameter, turbulence intensity and wind shear. As a result, simulated loads ware good agreed with the measured load. Therefore, the calculated design loads according to IEC 61400-1 standard were proved to valid.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.137-139
• /
• 1991

This paper proposes a minimum power factor control for maximum efficiency operation of an induction motor, under low load condition. Minimum input or maximum efficiency operation is achived by properly adjusting the amplitude of the stator voltage, with the three phase AC voltage controller. Through the simulation, the relationships between the delay angle and input power under various load conditions are examined. Experimental results are also given, which show good coincidence with the simulation results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 A
• /
• pp.115-117
• /
• 2002

In general, it is supposed that load characteristics of high and low voltage distribution line are always coincidence. But in practical distribution system, voltage variation characteristics of high and low voltage distribution line are not same. Then in this paper, we proposes a voltage regulation method considering load variation characteristics of high and low voltage distribution line in distribution system.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.3-32
• /
• 2008

The potential deep geothermal resources span a wide range of heat sources from the earth, including not only the more easily developed, currently economic hydrothermal resources; but also the earth's deeper, stored thermal energy, which is present anywhere. At shallow depths of 3,000~10,000m, the coincidence of substantial amounts heat in hot rock, fluids that heat up while flowing through the rock and permeability of connected fractures can result in natural hot water reservoirs. Although conventional hydrothermal resources which contain sufficient fluids at high temperatures and geo-pressures are used effectively for both electric and nonelectric applications in the world, they are somewhat limited in their location and ultimate potential for supplying electricity. A large portion of the world's geothermal resource base consists of hot dry rock(HDR) with limited permeability and porosity, an inadquate recharge of fluids and/or insufficient water for heat transport. An alternative known as engineered or enhanced geothermal systems(EGS), to dependence on naturally occurring hydrothermal reservoirs involves human intervention to engineer hydrothermal reservoirs in hot rocks for commercial use. Therefore EGS resources are with enormous potential for primary energy recovery using an engineered heat mining technology, which is designed to extract and utilize the earth's stored inexthermal energy. Because EGS resources have a large potential for the long term, United States focused his effort to provide 100GW of 24-hour-a-day base load electric-generating capacity by 2050.

• 한국분말재료학회지
• /
• 제8권2호
• /
• pp.124-130
• /
• 2001

A centrifugally atomized 2024A1/SiC/sub p/ composites were extruded to study effect of clusters on mechanical properties, and a model was proposed that the strength of MMCs would be estimated from the load transfer model approach that taken into consideration of the clusters. This model has been successfully utilized to predict the strength and fracture toughness of MMCs. The experimental and calculated results show coincidence and that the fracture toughness decreases with increasing the volume fraction of particles. On the basis of experimental observations, we suggest that the strength and fracture toughness of particle reinforced MMCs may be calculated from; σ/sub y/=σ/sub m/V/sub m/+σ/sub r/(V/sub r/-V/sub c)-σ/sub r/V/sub c/, K/sub IQ/=σ/sub Y/((3πt)((r/sub r//V/sub r/)(r/sub c//V/sub c/))/sup 1/2/)/sup 1/2/, respectively.

• 전산구조공학
• /
• 제1권2호
• /
• pp.101-109
• /
• 1988

구조물이 대형화되고 복잡해짐에 따라 구조물의 체계신뢰도 평가는 매우 어려워지며 많은 계산량을 요구한다. 특히 작용하중들이 시간적 변화특성을 가지거나 구조물의 파괴모드가 여러가지인 경우는 더욱 복잡하다. 구조물에 작용하는 대부분의 하중들은 그 발생강도 뿐만 아니라 발생시기, 발생빈도 등이 무작위특성을 가지므로, 이러한 시간적 변화특성을 합리적으로 반영하기 위해서는 종래의 확률변수 모형보다는 확률과정을 이용한 모형화가 바람직하다. 구조물 체계신뢰도의 근사해법으로 3계구간식 상한치를 이용한 점추정식 근사해가 제안되어졌다. 이 3계 점추정식 근사해는 현재 많이 사용되는 다른 근사해들과 비교할 때 적은 계산량의 증가에도 불구하고 정확도가 상당히 높으며 체계파괴확률 함수의 연속성이 보장된다. 상시하중과 함께 여러 일시하중이 작용할 때, 하중 조합효과를 보다 효과적으로 반영하기 위해 기존의 하중합치법을 보완하여 넓은 한계수준에서 정확도를 높였다.

• 수산해양기술연구
• /
• 제21권2호
• /
• pp.142-150
• /
• 1985

1. 반구형 각의 분포 및 집중하중에 의한 좌굴응력 해석은 변형된 각의 형상에 따라 타원체 각의 응력으로 해석함이 타당하다. 2. 일정 한계이상의 형상계수를 갖는 반 구형각에 대하여서는 재료상수를 형상계수의 승수로 고려한 수정된 임계좌굴 하중으로 탄소성 좌굴을 판정함이 더 양호한 결을 준다. 3. 탄소성 좌굴에 있어서 소모된 소성변형 에너지를 계산하기 위하여 항성변형 에너지를 계산하기 위하여 항상선를 따르는 에너지법을 이용하면 양호한 결과를 얻을 수 있다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.558-560
• /
• 2004

Studies on the controlled switching method have been done to prevent the power system surges which cause the insulation deterioration and electro magnetic compatibility (EMC) problems during closing and opening of a circuit breaker. The controlled switching method controls the closing and tripping time in coincidence with the voltage or current to suppress switching surge. It is used to switch condenser bank, no load transformer, and shunt reactor. In this study, basic concept of the controlled switching is introduced, and also the test is performed to find parameters of the controlled switching in a 24kV vacuum circuit. And then, the control device hardware using TMS320C31 DSP has been designed and manufactured. It has been found that the application of IT technology to a circuit breaker is very effective to depress the switching surge.

• 한국안전학회지
• /
• 제20권2호
• /
• pp.127-132
• /
• 2005

The purpose of this study is to compare representative posture classification schemes of OWAS, RULA and REBA in terms of correctness for postural load. The comparison was based on the evaluation results by the three methods for 224 working postures sampled from steel, electronics, automotive, and chemical industries. The results showed that OWAS and REBA generally underestimated postural stress than RULA irrespective of industry type, work performed and whether or not leg posture is balanced. While about $71\%\;and\;73\%$ of the 224 posture were evaluated with the action category/level 1 or 2 by OWAS and REBA respectively, about $60\%$ of the postures were classified into the action level of 3 or 4 by RULA. The coincidence rate of postural stress category between OWAS and RULA was just $33.5\%$, while the rate between RULA and REBA was $46.0\%$. It is concluded from the findings of this study and the previous research that compared to OWAS and REBA, RULA more precisely evaluates postural stress.

• Earthquakes and Structures
• /
• 제13권1호
• /
• pp.1-8
• /
• 2017

This article is all about using the MR damper with an external lever system for mitigation torsional and transitional lateral displacements by using of PID control algorithm. The torsional modes are so destructive and can be varied during an earthquake therefore, using a semi-active control system mostly recommended for them. In this paper the corner lateral displacement of each floor obtains and then it equivalents in a solid member and it connects to an MR damper, which relies to a rigid structure to reduce the response. An MR damper is a semi-active control system, which can absorb a lot of energy by injecting current to it. This amount of current is very low and needs low power supply, but it increases the amount of damper force, rather than inactive systems like viscous dampers. This paper will show the appropriate algorithm for current injection into MR damper when the eccentricity of the load is changed by using of Bouc-Wen and Bingham's methods and illustrates the coincidence of them.