• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.489-492
• /
• 2005

We report new polymer stabilized ferroelectric liquid crystal (PSFLC) cells with mechanical stability which is achievable by introducing photospacers in the cells. It was found that the mechanical st ability of the PSFLC cell was effected by introduction of photo spacers. We analyzed the dependence of mechanical stability and memory property on the density of photospacers in the PSFLC cell. The stability and memory properties of PSFLC Cells depending on photospacer density are discussed. 1. Introduction Recently, flexible displays have attracted much attention because they have remarkable advantages: thinner, lighter, non-breakable and conformable features. Flexible displays have various potential applications such as e-book and e-paper displays utilizing the distinct features. E-book and E-paper displays demand very low power consumption, so that bistable memory liquid crystal modes are required in case of flexible plastic LCDs for those application. Three kinds of memory LC modes have been developed; bistable nematic, bistable cholesteric and bistable FLC. Among them SSFLC as one of bistable FLC has big advantages such as low driving voltage, wide view angle and fast response time, SSFLC cells are, however, very weak against mechanical shock. Polymer stabilized FLC (PSFLC) has been developed to overcome the poor mechanical stability of SSFLC. PSFLC was known to have network structure that FLCs are oriented with smectic layer ordering in polymer network. The polymer network stabilizes the FLC orientation, which leads to improvement of mechanical stability of PSFLCD. A lot of studies have been done for the application of PSFLC to flexible $LCDs.^{[1{\sim}12]}$ However, it should be noted that PSFLC does not have sufficient mechanical stability for the particular applications such as smart card LCD, where LCD is highly bendable.Bead spacer was mainly used to maintain cell gap of conventional PSFLCDs. But the spacer density of it is not locally uniform in the cell, so that it is generally difficult that the PSFLCDs with bead spacers show sufficient mechanical stability. In order to more improve the mechanical stability of PSFLCDs, we introduced photospacers into PSFLCDs. In this paper, we describe the improvement of mechanical stability by introducing photospacers into PSFLCDs.

• Clean Technology
• /
• v.18 no.1
• /
• pp.69-75
• /
• 2012

In this study, we executed an environmental impact assessment about recycling of ITO (Indium Tin Oxide), used for touch panel. ITO is mainly used to make transparent conductive coatings for touch and flat screen LCD (Liquid Crystal Display), ELD (Emitting Light Device), PDP (Plasma Display Panel). This demand is increasing little by little. but form current status, ITO is discarded than recycling. It is important to recycling ITO for national strategies about resource conservation, and reduce environmental burden. Also Landfill or incineration of ITO cloud be harmful to the human health in the long-term. Material Life Cycle Assessment method (MLCA) was conducted for comparison landfill and recycling of ITO. MLCA would provide more information for environmental issues and potential environmental impacts of ITO. The study includes two scenarios, the basic scenario is recycling of ITO (10, 20, 30%) and the other scenario is landfill of ITO. In addition, amount of carbon dioxide and energy were calculated.

• Resources Recycling
• /
• v.24 no.1
• /
• pp.58-65
• /
• 2015

Although Korea is a top market sharing and world leading producer and developer of flat panel display devices, relevant recycling technology is not up to her prestigious status. Besides, most of the waste glass arising from flat panel displays is currently land-filled. The present paper mainly reviews on development of recycling systems for waste TFT-LCD glass from end-of-life LCD TVs and monitors and TFT-LCD process waste of crushed glass particles with target end uses of raw material for high strength concrete pile and glass fibers, respectively. Waste LCD glass was recycled to fabricate ingredients for high strength concrete piles with enhanced physical properties and spherical foam products. The waste LCD glass recycling technology is already developed to fabricate long and short fibers at commercial level. In view of these, future R & D on waste LCD glass materials is to be directed toward implementation of commercial materials recycling system therefrom.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.239-242
• /
• 2006

LCD-BLU (Liquid Crystal Display - Back Light Unit) is one of kernel parts of LCD unit and it consists of several optical sheets(such as prism, diffuser and protector sheets), LGP (Light Guiding Plate), light source (CCFL or LED) and mold frame. The LGP of LCD-BLU is usually manufactured by forming numerous dots with $50{\sim}200$ um in diameter on it by etching process. But the surface of the etched dots of LGP is very rough due to the characteristics of the etching process during the mold fabrication, so that its light loss is high along with the dispersion of light into the surface. Accordingly, there is a limit in raising the luminance of LCD-BLU. In order to overcome the limit of current etched dot patterned LGP, optical pattern design with 50um micro-lens was applied in the present study. The micro-lens pattern fabricated by modified LiGA with thermal reflow process was applied to the optical design of LGP. The attention was paid to the effects of different aspect ratio (i.e. $0.2{\sim}0.5$) of optical pattern conditions to the brightness distribution of BLU with micro-lens patterned LGP. Finally, high aspect ratio micro-lens patterned LGP showed superior results to the one made by low aspect ratio in average luminance.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.233-236
• /
• 2000

The structural, electrical and chemical characteristics of Al alloy thin film with low impurity concentrations AlW deposited by using dc magnetron sputtering deposition are investigated for the applications as data bus line in the TFT-LCD panel. The deposited thin films show the decrease of resistivity and the increase of grain size after the RTA at $300^{\circ}C$ for 20 min.. Moreover, the resistivity of AlW does not show appreciable grain size dependence after RTA. It is concluded that the decrease of resistivity after RTA is due to the increase of grain size. The annealed AlW is found to be hillock free. And for investigating chemical attack in TFT-LCD etching processing the electric potential of AlW alloy for Ag/AgCl were investigated by cyclic voltammetry. When W wt.% of AlW alloy was higher than about 3%, the electric potential of AlW was more positive than ITO's. Therefore AlW alloy thin film can be propose to use for data bus line.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.43-43
• /
• 2008

Recently, it is widely studied to liquid crystal (LC) alignment using ion-beam exposure. Because conventional rubbing method has some problems such as defects from dust and electrostatic charges and rubbing scratch during rubbing process. Moreover rubbing method needs cleaning process to remove these defects. Therefore rubbing-free techniques like ion-beam method are strongly required. We studied LC alignment by controlling ion-beam irradiation angles and electro-optical (EO) characteristics of twisted nematic LC on the polyimide surface. In this experiment, a good uniform alignment of the nematic liquid crystal (NLC) with the ion-beam exposure on the polyimide (PI) surface was observed. We also achieved low pretilt angle as function of ion-beam irradiation angles. X-ray photoelectron spectroscopic (XPS) analysis provided chemical evidence for LC alignment by controlling ion-beam irradiation angles. In addition, it can be achieved the good EO properties of the ion-beam-aligned twisted nematic liquid crystal display (TN-LCD) on PI surface. Some other experiments results and discussion will be included in the presentation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.535-538
• /
• 2003

Liquid crystal molecules with a new fluoro-isothiocyanate moiety were synthesized. They showed remarkably high $T_{NI}$ (>190 $^{\circ}C$), wide mesophase range of 170 $^{\circ}C$, high dielectric anisotropy (>14) and high optical anisotropy (>0.28). New LC Mixtures of the high $T_{NI}$ (>$85^{\circ}C$) was blended with the novel fluoro-isothiocyanate containing LC molecules, phenylcyclohexanes, bicyclohexanes and ester compounds. The LC mixtures show a fast speed (<10ms) of the below one frame rate in 17" WXGA panel.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.3
• /
• pp.245-249
• /
• 2007

The liquid crystal display (LCD) applications treated on the organic overcoat thin film surfaces by ion beam irradiation was successfully studied. The good LC aligning capabilities treated on the organic overcoat thin film surfaces with ion beam exposure of $60^{\circ}$ for 2 min above ion beam energy of 1200 eV can be achieved. But, the alignment of defect of NLC on the organic overcoat surface at low energy of 600 eV was measured. The pretilt angle of NLC on the organic overcoat thin film surface with ion beam exposure of $60^{\circ}$ for 2 min at energy of 1800 eV was measured about 1 degree. Finally, the good thermal stability of LC alignment on the organic overcoat thin film surface with ion beam exposure of $60^{\circ}$ for 2 min until annealing temperature of $200^{\circ}C$ can be measured.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.73-74
• /
• 2000

In recent years, attempts have been made to greatly improve the display quality of active-matrix liquid crystal display devices, and many techniques have been proposed to solve such problems as gate signal delay, feed-through voltage and image sticking[1-3]. To improve these problems which are caused by the feed-through voltage, we have evaluated new driving methods to reduce the feed-through voltage. Two level gate-pulse was used for the gate driving of the cst-on-common structure pixels. These gate driving methods offer better feed-through characteristics than conventional simple gate pulse. Optimized step signal will compensate by step pulse time and voltage. The evaluation of the suggested driving methods were performed by using a TFT-LCD array simulator PDAST which can simulate the gate, data and pixel voltages of a certain pixel at any time and at any location on a TFT array. The effect of the new driving method was effectively analyzed.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1411-1413
• /
• 1997

The thin film that is electrically conductive and optically transparent is called conductive transparent thin film. ITO(Indium-Tin Oxide) which is a kind of conductive transparent thin film has been widely used in solar cell, transparent electrical heater, selective optical filter, FDP(Flat Display Panel) such as LCD (Liquid Crystal Display), PDP(Plasma Display Panel) and so on. Especially in PDP, ITO films is used as a transparent electrode in order to maintain discharge and decrease consumption power through the improvement of cell structure. In this study, we prepared ITO by reactive r.f. sputtering with indium-tin(Sn wt 10%) alloy target instead of indium-tin oxide target. The ITO films deposited at low temperature $150^{\circ}C$ and 8% $O_2$ partial pressure showed about $3.6{\Omega}/{\square}$. At the end of firing, the resistance of ITO was decreased, the optical transparence was improved above 90%.