• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.517-524
• /
• 2001

In this study, the effect of relative density and fine contents(Finer then # 0.08mm sieve) on liquefaction phenomenon in reclaimed land by hydraulic hammer compaction is analyzed. For more site-specific studies, reclaimed land in Inchon International Airport is selected and the cyclic triaxial tests are performed on disturbed samples. In cyclic triaxial tests, the characteristics of reclaimed land in Inchon International Airport are considered sufficiently. The liquefaction resistance stress ratio ($\tau$$\ell$/$\sigma$v') can be defined by relative density 40, 50, 60, and 70% and also by fine contents : 0, 10, 20, 30, and 40% under relative density (D$\_$r/) 50% used disturbed samples. From tile result of comparing tile cyclic triaxial tests, it is shown that the liquefaction strength of soil increases with increases of relative density and fine contents. Fspecially fine contents is the main factor affecting the liquefaction potential. In addition, the liquefaction resistance stress ratio is reduced by the increase of fine content and tile ratio of change is steep until fine contents 20% and that is flexible during the range of fine contents 20% to 40%. Through this study, it is proved that the soil characteristics (fine contents 5∼20%) of the reclaimed land in Inchon International Airport flays an important role in the reduction of liquefaction potential.

• 한국농공학회논문집
• /
• 제48권4호
• /
• pp.67-74
• /
• 2006

This study was carried out to investigate the liquefaction behaviour of saturated silty sand under monotonic loading conditions. The undrained soil tests were conducted using a modified triaxial cell and specimens were prepared using the moisture tamping method. Undrained triaxial compression tests were performed at different confining pressures, void ratios and overconsolidation ratios and the samples were sheared to axial strains of about 20% to obtain monotonic loading conditions. It is shown that increasing confining pressures, void ratios and overconsoildation ratios increases the deviator stress, but it has no effect on increasing the dilatant tendencies. It is shown that complete static liquefaction was observed regardless of increases in the confining pressure, void ratio and overconsolidation ratio. Therefore, the confining pressure, void ratio and overconsoildation ratio does not provide significant effects on the liquefaction resistance of the silty sand. The presence of fines in the soil was shown to greatly increase the potential for static liquefaction and creates a particle structure with high compressibility for all cases.

• 한국지반공학회논문집
• /
• 제17권6호
• /
• pp.235-244
• /
• 2001

액상화는 비배수조건에서 흙 강도의 갑작스러운 감소에 기인한다. 이러한 흙 강도의 손실은 과잉간극수압의 발현과 관련된다. 본 연구에서는 최대 및 최소간극비에 영향을 미치는 세립분 함유량이 조사되었다. 또한 포화된 실트질 모래에 대한 정적 및 동적 삼축시험의 결과를 제시하였다. 이들 시험은 액상화강도와 정적 및 동적 거동 특성을 평가하기 위해 수행되었다. 시료는 새만금 유역에서 채취되었으며 공기건조되었다. 결과를 요약하면 다음과 같다. 1) 최대 및 최소간극비선은 유사한 경향으로 나타났다. 2) 최대 및 최소간극비는 20~30%의 세립분 함유량에서 얻어졌다. 3) 구속압력과 과압밀비가 증가할수록 액상화에 대한 저항은 증가하였다. 4) 불안정마찰각은 초기상대밀도의 증가와 함께 커졌다. 5) 유효응력비가 증가함에 따라 액상화에 대한 저항은 감소하였다.

• 한국지반환경공학회 논문집
• /
• 제23권5호
• /
• pp.5-13
• /
• 2022

본 연구에서는 국내 지진모의시험 수행 시 모래지반의 모사를 위해 국내에서 널리 이용되는 지반재료인 인공규사를 대상으로 상대밀도 차이에 따른 진동삼축시험을 수행하여 인공규사의 동적특성 및 액상화 저항특성을 실험적으로 분석하였다. 상대밀도 조건을 40%, 60%, 80%로 달리한 시험결과를 통해 상대밀도에 따른 액상화 저항특성을 확인하였으며, 액상화 진동저항응력비(Cyclic resistance stress ratio, CRR) 산정 곡선을 도시하였다. 또한, 액상화 진동저항응력비(CRR) 산정곡선의 타당성을 검토하기 위해 실내진동삼축시험에 사용된 규사로 이루어진 인공지반을 조성한 후, 간편예측법과 상세예측법을 통한 액상화 평가를 수행하여 각각의 안전율을 비교·검토하였다. 최종적으로, 상대밀도를 달리한 실험을 통해 인공규사의 동적물성을 파악하여 결과를 도출하였으며, 이 결과를 물성치로 적용한 상대밀도 40% 간편예측법은 안전율이 1로 안전한 지반으로 도출된 반면 상세예측법은 0.05작은 값으로 결과가 도출되었다.

• 한국지반신소재학회논문집
• /
• 제13권2호
• /
• pp.49-57
• /
• 2014

본 연구에서는 남극 장보고기지 부근에서 채취한 시료를 활용하여 동하중에 대한 액상화 저항특성을 파악하기 위하여 반복삼축시험을 실시하였다. 또한 기존문헌과의 비교를 통하여 남극에서 퇴적된 지반의 동적거동을 규명하였다. 시험결과 동일한 압밀응력비에 대한 반복회수와 축변형률 5%를 발생시키는데 필요한 반복응력비와의 관계는 모든 시료에서 초기액상화를 발생시킬 수 있는 반복응력비가 증가할수록 반복회수가 감소하였다. 세립분 함유량이 10%로 증가할수록 액상화 저항강도가 감소하다가 다시 증가하는 경향을 나타내었다. 점착력과 액상화 저항강도와의 관계는 세립분 함유량과 액상화 저항강도와의 관계와 같이 점착력이 증가할수록 액상화 저항강도도 감소하지만 어느 시점 이후에는 반복응력비가 증가하는 경향을 보였다. 또한, 마찰각과 평균입경이 증가할수록 반복응력비가 증가하는 경향을 나타내었다.

• Geomechanics and Engineering
• /
• 제3권2호
• /
• pp.83-108
• /
• 2011

The effect of non-plastic fines (silt) on liquefaction and pore pressure generation characteristics of saturated sands was studied through undrained stress controlled cyclic triaxial tests using cylindrical specimens of size 50 mm diameter and height 100 mm at different cyclic stress ratios and at a frequency of 0.1 Hz. The tests were carried out in the laboratory adopting various measures of sample density through various approaches namely gross void ratio approach, relative density approach, sand skeleton void ratio approach, and interfine void ratio approach. The limiting silt content and the relative density of a specimen were found to influence the undrained cyclic response of sand-silt mixtures to a great extent. Undrained cyclic response was observed to be independent of silt content at very high relative densities. However, the presence of fines significantly influenced this response of loose to medium dense specimens. Combined analyses of cyclic resistance have been done using the entire data collected from all the approaches.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.315-322
• /
• 2003

Cyclic simple shear tests were performed to find out the effect of preshear on dynamic strength of the sandy soil. Tests were performed for the specimens with 40% and 60% of relative density, under three different effective vertical stress of 50, 100 and 200kPa. For 50 and 100kPa, preshear ratios 0.00, 0.08, 0.12 and 0.16 were given, respectively, For low and high relative densities, two different results are shown in dynamic tests. Under the dense conditions, the maximum shear stress ratio($\tau$$\_$cyc//$\sigma$$\_$vo/) and the cyclic shear stress ratio($\tau$$\_$cyc//$\sigma$$\_$vo/) causing a certain shear strain increase with augmenting preshear ratio(${\alpha}$). However, the maximum shear stress ratio and the cyclic shear stress ratio increase or decrease with increasing preshear ratio under the loose conditions. Correction factor(K$\_$${\alpha}$/) for preshear increases at an early stage and then decreases with increasing preshear ratio at loose condition and increase with increasing preshear ratio at dense condition. Correction factor (K$\_$${\alpha}$,Max/) for preshear increases with the increasing preshear ratio irrespective of relative density, and the value of has same behavior as K$\_$${\alpha}$/.

• 대한토목학회논문집
• /
• 제28권2C호
• /
• pp.83-94
• /
• 2008

본 연구에서는 흙의 미소변형에서 대변형까지 고려할 수 있는 유효응력해석을 이용하여 매립지반에 대한 액상화 및 진동으로 발생하는 침하량을 예측하였다. 유효응력모델은 진동 중에 발생하는 과잉간극수압을 계산하여 이에 따른 흙의 강성저하와 수반되는 지반의 변위를 모델링하였다. 진동으로 인한 지반의 변형률 수준이 작은 경우에 적합한 등가선형해석을 이용한 액상화 평가를 실시하여 유효응력모델을 이용한 예측법과 비교하였다. 등가선형해석에서 계산된 전단응력비에 해당하는 표준관입시험치를 국내에서 발생 가능한 지진규모와 실트질 함유량에 따라 콘관입저항치로 환산한 값과 현장에서 계측된 콘관입저항치를 서로 비교하여 액상화 가능성을 예측하였다. 두 곳의 인천지역 매립지에 대한 액상화 해석을 위하여 매립지에서 계측된 콘관입저항치와 전단파 속도를 이용하여 입력 물성값을 결정하였다. 인천 매립지에 대한 두 액상화 해석 방법의 결과는 액상화 발생 여부에서 유사하였으며 깊이에 따른 연속적인 액상화 판정과 얇은 층의 액상화 예측이 가능하여 액상화 예측의 정밀도를 높였다. 유효응력모델을 이용한 액상화 해석 결과는 지표면 아래 20m 이내에서 초기 유효수직응력의 40%~70% 정도의 과잉간극수압이 발생하였으며 이로 인하여 지표면에서 10cm 미만의 침하가 발생하였다.

• 한국지진공학회논문집
• /
• 제24권5호
• /
• pp.197-209
• /
• 2020

Evidence of liquefaction during the 2017 Pohang earthquake has highlighted the urgent need to evaluate the current seismic design standard for liquefaction in Korea, particularly the liquefaction triggering standard. With the simplified method, which is the most popular method for evaluating liquefaction triggering, the factor of safety for liquefaction triggering is calculated via the cyclic stress ratio (CSR) and the cyclic resistance ratio (CRR). The parameters in the CSR and CRR have undergone changes over time based on new research findings and lessons learned from liquefaction case-histories. Hence, the current design standard for liquefaction triggering evaluation in Korea should also reflect these changes to achieve seismic safety during future earthquakes. In this study, liquefaction susceptibility criteria were discussed initially and this was followed by a review of the current liquefaction triggering codes/guidelines in other countries and Korea. Next, the parameters associated with the CSR such as the maximum ground acceleration, stress reduction factor, magnitude scaling factor, and overburden correction factor were discussed in detail. Then, the evaluation of the CRR using the SPT N-value and CPT qc-value was elaborated along with overburden and clean-sand correction factors. Based on this review of liquefaction triggering evaluation standards, recommendations are made for improving the current seismic design standard related to liquefaction triggering in Korea.

• Geomechanics and Engineering
• /
• 제10권1호
• /
• pp.77-94
• /
• 2016

Cyclic triaxial and resonant column tests were conducted to understand the beneficial effects of various grouted sands on liquefaction resistance and dynamic properties. The test procedures were performed on a variety of grouted sands, such as silicate-grouted sand, silicate-cement grouted sand and cement-grouted sand. For each type of grout, sand specimen was mixed with a 3.5% and 5% grout by volume. The specimens were tested at a curing age of 3, 7, 28 and 91 days, and the results of the cyclic stress ratio, the maximum shear modulus and the damping ratio were obtained during the testing program. The influence of important parameters, including the type of grout, grout content, shear strain, confining pressure, and curing age, were investigated. Results indicated that sodium silicate grout does not improve the liquefaction resistance and shear modulus; however, silicate-cement and cement grout remarkably increased the liquefaction resistance and shear modulus. Shear modulus decreased and damping ratio increased with an increase in the amplitude of shear strain. The effect of confining pressure on clean sand and sodium silicate grouted sand was found to be insignificant. Furthermore, a nonlinear regression analysis was used to prove the agreement of the shear modulus-shear strain relation presented by the hyperbolic law for different grouted sands, and the coefficients of determination, $R^2$, were nearly greater than 0.984.