• 비파괴검사학회지
• /
• 제20권1호
• /
• pp.54-61
• /
• 2000

피로손상이 발생하는 초기단계는 결정립계나 석출물, 그리고 잔류응력과 같은 전위(dislocation)의 이동성에 영향을 미치는 변수에 의해 지배되는 것으로 널리 알려져 있으나, 물리적으로 손상의 발생을 탐지할 수 있는 단계는 미소균열의 발생단계라 할 수 있다. 미소균열은 microcrack으로 부르는 것이 일반적이지만 피로손상의 문제에서만은 short(or small) fatigue crack으로 통용되고 있다. 따라서 미소균열 보다는 소균열 또는 피로 단균열이 더 알맞은 용어일지도 모르는데, 그 크기가 수 ${\mu}m$에서 수 mm의 범위에 걸친 균열의 총칭이다. 이러한 크기라면 대략 통상적인 비파괴시험 방법으로 탐지할 수 있는 범위의 한계 부근에 있으므로 피로손상의 탐지와 관련된 비파괴평가의 역할과 관련하여 새삼스럽게 한번 짚고 넘어가는 것도 의미 있는 일이라 생각된다. 피로와 관련하여 보고된 비파괴평가에 관한 연구는 감히 그 숫자를 헤아릴 수 없이 많으나 그 대부분은 피로균열의 성장 및 전파에 관한 것으로, 피로 단균열과 관련한 연구는 상대적으로 적으며 특히 국내에서는 거의 찾아볼 수 없다. 그러나 피로 단균열의 탐지와 관련하여 지금까지 전세계적으로 보고된 연구 결과는 다수 있으므로 여기서는 주로 비파괴평가로 볼 수 있는 연구에 대해서만 살펴보기로 한다.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.209-216
• /
• 2000

The lateral behavior of the moving web is critical to the quality of the web products. The alignment of the rollers carrying the web is found to be one of important factors to the lateral behavior of the moving web. But, the study on the effect of the tilting roller in the direction of the normal to the moving web on the lateral behavior has not been reported in the literature yet. For example, the contact roller often contacts the winding roll in a tilted fashion and causes the lateral motion of the winding web, which induces the offset on the wound roll. The lateral dynamics of the moving web induced by a tilted roller in normal direction of a web is investigated in this paper. The two-dimensional dynamic model developed by Shelton is extended to investigate the effect of a titled roller in a normal direction of the moving web on the lateral motion of the moving web. New boundary conditions are developed to solve the extended model. Computer simulation study proved that the model developed can be used to predict the lateral motion of the moving web ？ to a tilted roller in normal direction of the moving web. The lateral deflection is increased exponentially a the tilting angle is increased. As the length of web span is increased, the amount of lateral deflection was increased almost linearly for the same tilting angle. The lateral dynamics turned out to be almost independent to the operating tension. The model developed can be used to solve the offset problem of the staggered winding and also to design a new web guiding mechanism.

• 한국전기전자재료학회논문지
• /
• 제21권12호
• /
• pp.1063-1070
• /
• 2008

The performance of an acoustic transducer is determined by the effects of many design variables, and mostly the influences of these design variables are not linearly independent of each other. To achieve the optimal performance of an acoustic transducer, we must consider the cross-coupled effects of the design variables. In this study, the variation of the performances of underwater acoustic transducer in relation to its structural variables was analyzed. In addition, the new optimal design scheme of an acoustic transducer that could reflect not only individual but also all the cross-coupled effects of multiple structural variables, and could determine the detailed geometry of the transducer with great efficiency and rapidity was developed. The validation of the new optimal design scheme was verified by applying the optimal structure design of a flextensional transducer which are the most common use for high power underwater acoustic transducer. With the finite element analysis(FEA), we analyzed the variation of the resonance frequency, sound pressure, and working depth of a flextensional transducer in relation to its design variables. Through statistical multiple regression analysis of the results, we derived functional forms of the resonance frequency, sound pressure, and working depth in terms of the design variables. By applying the constrained optimization technique, Sequential Quadratic Programming Method of Phenichny and Danilin(SQP-PD), to the derived function, we designed and verified the optimal structure of the Class IV flextensional transducer that could provide the highest sound pressure level and highest working depth at a given operation frequency of 1 kHz.

• 한국경영과학회:학술대회논문집
• /
• 대한산업공학회/한국경영과학회 2000년도 춘계공동학술대회 논문집
• /
• pp.53-56
• /
• 2000

그로벌최적화문제(Global optimization problem)의 부류인 다목적선형계획법 ( MOLP ) (Multiple objective linear programming)에서 결정된 유효해집합(a set of efficient solutions)위에서 선형함수 최적화문제 ( Ρ )는 해집합이 볼록집합이 아니므로(nonconvex set) 일반적인 선형계획법을 활용하기가 어렵다. 현재까지 ( Ρ )의 최적화를 위해서 유효해집합의 모든 꼭지점(extreme point)를 찾거나 일련의 선형계획문제들을 최적화하여 최적해를 찾는 접근방법들이 있다. 이러한 방법들에는 ( MOLP )의 해집합의 차원(dimension)이 커짐에 따라 문제해결이 실제적으로 가능하지 않는 경우가 많다. 본 연구는 주어진 선형함수와 다목적선형함수들간 관계를 고찰하여 선형목적함수를 구성하고 그 목적함수를 이용하여 주어진 문제 (Ρ) 의 최적해를 찾는 선형계획적 접근방법을 제안한다.

• 한국전기전자재료학회논문지
• /
• 제13권6호
• /
• pp.485-492
• /
• 2000

The sintering characteristics and the effects of density on dielectric properties in 0.2Ba(Mg$_{1}$3(Nb$_{2}$3/)O$_3$-0.8Ba(Mg$_{1}$3//Ta$_{2}$3/)O$_3$ceramics were investigated. The samples were made by the powder mixing techniques with the two step calcining conditions. When the 1st and the 2nd calcining temperatures were 120$0^{\circ}C$ and the sintering temperature was 155$0^{\circ}C$the density of samples showed the highest value (7.45 g/cm$^3$, 98.5% of theoretical density) among them. The dielectric constant of samples was nearly independent of density but the tan $\delta$ and the temperature coefficient of dielectric constant decreased linearly with increasing of the density. The quality factor(Q$\times$f), the temperature coefficient of resonance frequency and the dielectric constant of Ba[Mg$_{1}$3(Nb$_{0.2}$/Ta$_{0.8}$)sub 2/3/]O$_3$ceramic were 79,548 GHz, +1.5 ppm/$^{\circ}C$ and 26 in the microwave range, respectively.ely.

• Tribology and Lubricants
• /
• 제25권6호
• /
• pp.432-437
• /
• 2009

The effect of oxidation in SAE 5W30 engine oils on friction and wear characteristics was investigated using reciprocating bench tester and shell 4-ball tester. Commercial engine oils were collected and oxidized using the KS M 2021 method modifying the oxidation time. Kinematic viscosity, total acid number(TAN), FT-IR spectrum and total base number(TBN) also measured to examine the chemical change of oils with oxidation. The results showed that TAN was slightly changed and Kinematic viscosity was suddenly increased during the oxidation stage. however, TBN results keep a constant slope after TBN linearly decreased with oxidation time. Spectroscopy results showed that spectrums were orderly increased at $1710cm^{-1}$ during the oxidation time. Friction test results showed that oxidation of oils formed unstable friction layers causing higher fluctuating friction. however, the wear resistance was independent of oxidized time due to the different friction characteristics by oxidation. We found several factors in relation to lubrication properties with oxidation time. This factors were Viscosity, TBN, change of FT-IR spectrum, friction coefficient using reciprocating bench tester and wear scar.

• 건축역사연구
• /
• 제18권2호
• /
• pp.7-26
• /
• 2009

The purpose of this paper is the study on the architectural characteristics revived from the roman architecture, focused on the early renaissance architecture building. The results of study are as follow: 1. The composition system of Domus which is formed of urban house in the Roman period is presented by spatial arrangement of palace architecture centering around atrium in the Renaissance period. Thus plan type of Domus is used by atrium from which is composed of peristyle from the palace and villa in the Renaissance period. 2. The circular temple in the Roman period is composed of element such as podium, stair, peristyle centering around the basic circular plan. Bramante planed to revive above elements for the Tempietto to concept from the circular temple in the Roman period. 3. The triumphal arch in the Roman period is strong monument to the independent building in the city, but thus arch is used of church facade as the important example which is composed with building elevation in the Renaissance period. 4. The composition system and element of Roman temple which is planned to rectangular plan is composed of high podium, stair, portico, prostyle and pediment. The facade plan of church is used by the partial elements and total elements perfectly from the temple in the Roman period. 5. The linearly successive and repetitive composition which is composition system and element of aqueduct arches of same dimension shows to the palace facade, arcade for gallery space and side elevation plan of S.Fracesco church. 6. Such as background of Colloseum, Rucellai palace can be called good example which is created by the new architectural form to the creative starting point from the classical architecture from.

• 한국음향학회지
• /
• 제22권4호
• /
• pp.299-307
• /
• 2003

화자독립 음성인식기에서 화자사이의 성도 길이의 영향을 최소화시켜 인식 성능을 개선하는 화자 정규화에 대한 많은 연구가 있어 왔다. 본 연구에서는 벡터양자화기를 이용하여 화자 검증이 가능하다는 사실에 착안하여 벡터 양자화기를 이용한 비교적 간단한 선형 워핑 화자정규화방법을 제안한다. 제안하는 방법에서는 먼저 정규화에 이용될 최적의 코드북을 생성한 다음, 이 코드 북을 이용하여 화자의 선형 워핑계수를 추출하고 추출된 워핑계수는 멜 켑스트럼 추출시에 사용되는 멜스케일 필터뱅크를 워핑하기 위해 이용된다. 본고에서 제안한 워핑계수 추출 및 적용 방법의 성능을 확인하기 위해 이산 HMM을 이용한 13가지의 단음절 한글 숫자음 인식기를 이용하여 인식실험을 수행하였으며, 실험 결과 약 29%의 오인식률 감소를 보여 제안하는 화자 정규화방법이 다른 라인서치 워핑계수추출 방법보다 간단한 동시에 효용가치가 있음을 확인하였다.

• 한국정밀공학회지
• /
• 제19권7호
• /
• pp.106-115
• /
• 2002

Growth characteristics of micro carbon structures fabricated by laser-assisted chemical vapor deposition are studied. Argon ion laser and ethylene were used as the energy source and reaction gas, respectively, to grow micro carbon rod through pyrolytic decomposition of the reaction gas. Experiments were performed at various conditions to investigate the influence of process parameters on growth characteristics such as the diameter or growth rate of the micro carbon rod with respect to reaction gas pressure and incident laser power. Reaction gas pressure in experiments ranges from 200 to 600Torr and the incident laser power from 0.3 to 3.8W. For these conditions, the diameter of the rod increases linearly with respect to the laser power but is almost independent of the reaction gas pressure. Growth rate of the rod changes little with gas pressure when the laser power remains below IW. For a constant reaction gas pressure, the growth rate increase with Increasing laser power, but the rate of increase decreases gradually, implying that the chemical vapor deposition condition changes from a kinetically-limited regime to a mass-transport-limited regime. When the carbon rod was grown at near threshold laser power, a very smooth surface is obtained on the rod. By continuously moving the focusing lens in the direction of growth, a micro carbon rod with a diameter of 287${\mu}{\textrm}{m}$ and aspect ratio of 100 was fabricated..

• 한국지반공학회논문집
• /
• 제29권3호
• /
• pp.61-70
• /
• 2013

모래에 혼합된 점토의 혼합비에 의한 투수계수와 압밀계수의 영향분석을 위해 주문진 표준사와 오타와 모래에 카올린 점토를 다양한 혼합비로 섞은 시료를 제작하여 연성벽체투수시험을 실시하였다. 시험결과 시험이 실시된 10%에서 29%의 카올린 점토 혼합범위에서는 세미 로그 그래프 상에서 점토의 혼합비와 투수계수 및 압밀계수가 "반비례하는 선형적 상관관계를 나타내었다. 또한 투수계수와 압밀계수는 흙의 구조에 의해서 결정되는 것으로 나타났다. 점토비가 낮아 안정구조로 볼 수 있는 혼합토에서는 점토질 토사에서 투수계수 및 압밀계수와 높은 연관성을 가지고 있는 것으로 알려진 간극비와는 상호관계를 나타내지 않은 반면, 부유구조에서는 간극비의 증가에 따라서 투수계수가 감소하는 것으로 나타났다.