• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.424-429
• /
• 2018

In this study, an expansion joint that is susceptible to waterhammer was tested for its vibration durability. The operation data for the hydraulic actuator was the expansion length of the expansion joint when the waterhammer occurred. In the case of the vibration durability test, the internal temperature status of the expansion joint was assumed to be a stress factor and a lifespan prediction model was assumed to follow the Arrhenius model. A test was carried out by increasing the internal temperature status at $30^{\circ}C$, $50^{\circ}C$, and $65^{\circ}C$. By a linear transformation of the lifespan data for each temperature, a constant value and activation energy coefficient was induced for the Arrhenius equation and verified by comparing the value of a lifetime prediction model with the experimental value at $85^{\circ}C$. The failure modes of the ongoing or finished test were leakage, bellows separation, and internal deformation. In the future, a composite lifespan prediction model, including two more stress factors, will be developed.

• Nuclear Engineering and Technology
• /
• v.53 no.2
• /
• pp.603-610
• /
• 2021

The major drawback of zirconia-based materials, in view of their applications as targets for minor actinide transmutation, is their poor thermal conductivity. The addition of MgO, which has high thermal conductivity, to zirconia-based materials is expected to improve their thermal conductivity. On these grounds, the present study aims at phase characterization and thermophysical property evaluation of neodymium-substituted zirconia (Zr_0.8Nd_0.2O_1.9; using Nd₂O₃ as a surrogate for Am₂O₃) and its composites with MgO. The composite was prepared by a solid-state reaction of Zr_0.8Nd_0.2O_1.9 (synthesized by gel combustion) and commercial MgO powders at 1773 K. Phase characterization was carried out by X-ray diffraction and the microstructural investigation was performed using a scanning electron microscope equipped with energy dispersive spectroscopy. The linear thermal expansion coefficient of Zr_0.8Nd_0.2O_1.9 increases upon composite formation with MgO, which is attributed to a higher thermal expansivity of MgO. Similarly, specific heat also increases with the addition of MgO to Zr_0.8Nd_0.2O_1.9. Thermal conductivity was calculated from measured thermal diffusivity, temperature-dependent density and specific heat values. Thermal conductivity of Zr_0.8Nd_0.2O_1.9-MgO (50 wt%) composite is more than that of typical UO₂ fuel, supporting the potential of Zr_0.8Nd_0.2O_1.9-MgO composites as target materials for minor actinides transmutation.

• Steel and Composite Structures
• /
• v.15 no.5
• /
• pp.481-505
• /
• 2013

This paper focuses on thermal post-buckling analysis of functionally graded beams with temperature dependent physical properties by using the total Lagrangian Timoshenko beam element approximation. Material properties of the beam change in the thickness direction according to a power-law function. The beam is clamped at both ends. In the case of beams with immovable ends, temperature rise causes compressible forces and therefore buckling and post-buckling phenomena occurs. It is known that post-buckling problems are geometrically nonlinear problems. Also, the material properties (Young's modulus, coefficient of thermal expansion, yield stress) are temperature dependent: That is the coefficients of the governing equations are not constant in this study. This situation suggests the physical nonlinearity of the problem. Hence, the considered problem is both geometrically and physically nonlinear. The considered highly non-linear problem is solved considering full geometric non-linearity by using incremental displacement-based finite element method in conjunction with Newton-Raphson iteration method. In this study, the differences between temperature dependent and independent physical properties are investigated for functionally graded beams in detail in post-buckling case. With the effects of material gradient property and thermal load, the relationships between deflections, critical buckling temperature and maximum stresses of the beams are illustrated in detail in post-buckling case.

• Journal of the Korean Ceramic Society
• /
• v.43 no.1 s.284
• /
• pp.48-54
• /
• 2006

Hydroxyapatite $(HAp,\;Ca_{10}(PO_4)_6(OH)_2)$/alumina composites were fabricated with the addition of fluorides, such as $MgF_2$ and $CaF_2$. In this study, the effect of fluorides on the inhibition of phase decomposition and the mechanical properties of HAp was investigated. Due to the higher solubility of F ion in HAp structure, $MgF_2$ additive was more effective compared to $CaF_2$ additive in the lowering decomposition temperature of HAp. Therefore, the dissociation tendency of HAp was fully inhibited below $1400^{\circ}C$. The mechanical properties of HAp composites with $MgF_2$ additive showed higher value (flexural strength: $\~170MPa$, Vickers hardness: $\~7\;GPa$, fracture toughness: $\~1.5\;MPam^{1/2}$) compared to $MgF_2-free$ composites. The linear thermal expansion coefficient of HAp composites with $MgF_2$ showed the value of $16.4\times10^{-6}/^{\circ}C\;at\;20\~400^{\circ}C $.

• Journal of the Korean Ceramic Society
• /
• v.27 no.7
• /
• pp.899-906
• /
• 1990

The cordierite powders were prepared from Mg(NO3)2.6H2O, Al(NO3)3.9H2O and colloidal silica by the coprecippitation method, and the sintering behavior of the powders were investigated. Two different methods were applied for producing the precursor powders. The one was to added the aqueous solution of Mg(NO3)2.6H2O and Al(NO3)3.9H2O to NH4OH to adjust pH at 10 where the colloidal silica of pH 10 was added. The other wa to add the aqueous solution of Mg(NO3)2.6H2O and Al(NO3)3.9H2O to the colloidal silica with NH4OH to control the final mixture to be at pH 10. It was confirmed that more homogeneous powders were obtained from the latter method. The firing linear shrinkage of the powder compacts fabricated from the calcined powder between 90$0^{\circ}C$ and 110$0^{\circ}C$ was found to be larger as the calcination temperature was low. But all of them stopped shrinking around 120$0^{\circ}C$. The powder compacts, fabricated using the calcined powders at 90$0^{\circ}C$ and 95$0^{\circ}C$ for 2hours and sintered at 142$0^{\circ}C$ for 2hours, showed relative density of 93-96%, 3-point bending strength of 81-83MPa, KIC of 1.9-2.4 MPam1/2 and thermal expansion coefficient of 0.213-0.732$\times$10-6$^{\circ}C$.

• Structural Engineering and Mechanics
• /
• v.44 no.1
• /
• pp.109-125
• /
• 2012

Post-buckling behavior of Timoshenko beams subjected to uniform temperature rising with temperature dependent physical properties are studied in this paper by using the total Lagrangian Timoshenko beam element approximation. The beam is clamped at both ends. In the case of beams with immovable ends, temperature rise causes compressible forces end therefore buckling and post-buckling phenomena occurs. It is known that post-buckling problems are geometrically nonlinear problems. Also, the material properties (Young's modulus, coefficient of thermal expansion, yield stress) are temperature dependent: That is the coefficients of the governing equations are not constant in this study. This situation suggests the physical nonlinearity of the problem. Hence, the considered problem is both geometrically and physically nonlinear. The considered highly non-linear problem is solved considering full geometric non-linearity by using incremental displacement-based finite element method in conjunction with Newton-Raphson iteration method. The beams considered in numerical examples are made of Austenitic Stainless Steel (316). The convergence studies are made. In this study, the difference between temperature dependent and independent physical properties are investigated in detail in post-buckling case. The relationships between deflections, thermal post-buckling configuration, critical buckling temperature, maximum stresses of the beams and temperature rising are illustrated in detail in post-buckling case.

• Steel and Composite Structures
• /
• v.33 no.6
• /
• pp.805-822
• /
• 2019

In this work, a simple four-variable integral plate theory is employed for examining the thermal buckling properties of functionally graded material (FGM) sandwich plates. The proposed kinematics considers integral terms which include the effect of transverse shear deformations. Material characteristics and thermal expansion coefficient of the ceramic-metal FGM sandwich plate faces are supposed to be graded in the thickness direction according to a "simple power-law" variation in terms of the "volume fractions" of the constituents. The central layer is always homogeneous and consists of an isotropic material. The thermal loads are supposed as uniform, linear, and nonlinear temperature rises within the thickness direction. The influences of geometric ratios, gradient index, loading type, and type sandwich plate on the buckling properties are examined and discussed in detail.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.5
• /
• pp.7-14
• /
• 2004

The interaction of incident manochromatic waves with an array of N surface-piercing porous dual cylindrical structures is investigated in the frame of three-dimensional linear potential theory. The dual cylindrical structure is camposed of concentric two cylinders. The exterior cylinder is porous and the interior cylinder is impermeable. The fluid domain is divided into N+1 regions i.e. a single exterior region and N interior regions. The diffraction potentials in each region representing the scattering of incident waves by an array of porous cylindrical structures are expressed by the Fourier Bessel series. The unknown coefficients in each region are determined by applying the porous boundary condition and continuity of mass flux at the matching boundary. It is found that an array of porous cylindrical structures reduces both the wave forces and the wave run-up, and shows the excellent performance of wave blocking. The results show that various types of breakwater exchanging seawater are prospective by controlling the porosity and the configuration of cylindrical structures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.141-146
• /
• 2013

This research investigates the stability analysis for the rotating and the stationary grooved journal bearing. The dynamic coefficients of the journal bearing are calculated by using FEM and the perturbation method. When journal bearing is in whirling motion, the dynamic coefficients have time-varying components as a sine wave due to the reaction force of oil film toward the center of journal even in the steady state. The solutions for the equations of motion can be assumed as the Fourier series expansion. The equations of motion can be rewritten as the linear algebraic equations with respect to the Fourier coefficients. Then, stability of the grooved journal bearing can be calculated by Hill's infinite determinant. The periodic function of dynamic coefficients is derived using Fourier Fast Transform(FFT).The stability of journal bearing is determined as rotating speed increases and the stability of rotating grooved journal bearing is compared and discussed with the stability of stationary grooved journal bearing.

• Journal of the Korean Ceramic Society
• /
• v.20 no.1
• /
• pp.25-30
• /
• 1983

This experiment was studied in the system of (1-x) CaO MgO $2SiO-Al_2O_3$ to investigate forming of solid solution. The technique empolyed was the well known water-quenching method. Differential thermal analysis of the each glass water quenched indicated that under 30 mole% $Al_2O_3$ was lowered with increasing of the amount of $Al_2O_3$ It was supposed by X-ray diffraction patterns of each specimen sintered at various temperature that only solid solution was formed under the 30mole % $Al_2O_3$ compositions solid solution and anorthite were formed at the 20mole% $Al_2O_3$ composition anorthite solid solution and spinel$(MgAl_2O_4)$ were formed over the 40mole% $Al_2O_3$ compositions. The maximum density and thermal expanison coefficient was 2.89g/cm 7.74x106./C$^{\circ}$ respectively in the composi-tion of 10 mole% $Al_2O_3$ . All the specimens showed linear thermal expansion behavior. Microhardness was as high as 850kg/nm2 in the composition of 5, 10, 20 mole % $Al_2O_3$ and dielectric constant was 7.3-6.9.