• International journal of advanced smart convergence
• /
• v.9 no.4
• /
• pp.26-33
• /
• 2020

This study measured the downward stepping movement relative to weight change (no load, and 10%, 20%, 30% of body weight respectively of adult male (n=10) from standardized stair (rise of 0.3 m, tread of 0.29 m, width of 1 m). The 3-dimensional cinematography and ground reaction force were also utilized for analysis of leg stiffness: Peak vertical force, change in stance phase leg length, Torque of whole body, kinematic variables. The strategy heightened the leg stiffness and standardized vertical ground reaction force relative to the added weights (p<.01). Torque showed rather larger rotational force in case of no load, but less in 10% of body weight (p<.05). Similarly angle of hip joint showed most extended in no-load, but most flexed in 10% of body weight (p<.05). Inclined angle of body trunk showed largest range in posterior direction in no-load, but in vertical line nearly relative to added weights (p<.001). Thus the result of the study proved that downward stepping strategy altered from height of 30 cm, regardless of added weight, did not affect velocity and length of lower leg. But added weight contributed to more vertical impulse force and increase of rigidity of whole body than forward rotational torque under condition of altered stepping strategy. In future study, the experimental on effect of weight change and alteration of downward stepping strategy using ankle joint may provide helpful information for development of enhanced program of prevention and rehabilitation on motor performance and injury.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.12
• /
• pp.1659-1665
• /
• 2019

In this paper, a novel design of a compact printed monopole antenna for wireless local area network (WLAN) applications is investigated. The radiator with a patch of different line width and step-shaped ground planes is used to reduce the antenna size. The size of the antenna is 16 × 17 × 1 ㎣ and is fabricated with a photolithography technique. The simulated and measured results agree well. The resonant frequency of the investigated antenna is about 5.2 GHz and can cover an impedance bandwidth of 1 GHz for the measurement result. In addition, we presented the measured radiation pattern, presented the gain and efficiency measured in the required WLAN 5 GHz frequency band (5.15-5.825 GHz), and confirmed that it can be used as a 5 GHz band WLAN antenna. The investigated antenna has a small size, light weight, low cost, omni-directional radiation pattern, high gain, and high efficiency.

• Journal of the Korean Physical Society
• /
• v.73 no.11
• /
• pp.1764-1773
• /
• 2018

A-PET is a quad-head PET scanner developed for use in small-animal imaging. The dimensions of its volumetric field of view (FOV) are $46.1{\times}46.1{\times}46.1mm^3$ and the gap between the detector modules has been minimized in order to provide a highly sensitive system. However, such a small FOV together with the quad-head geometry causes image quality degradation. The main factor related to image degradation for the quad-head PET is the mispositioning of events caused by the penetration effect in the detector. In this paper, we propose a precise method for modelling the system at the high spatial resolution of the A-PET using a LOR (line of response) based ML-EM (maximum likelihood expectation maximization) that allows for penetration effects. The proposed system model provides the detection probability of every possible ray-path via crystal sampling methods. For the ray-path sampling, the sub-LORs are defined by connecting the sampling points of the crystal pair. We incorporate the detection probability of each sub-LOR into the model by calculating the penetration effect. For comparison, we used a standard LOR-based model and a Monte Carlo-based modeling approach, and evaluated the reconstructed images using both the National Electrical Manufacturers Association NU 4-2008 standards and the Geant4 Application for Tomographic Emission simulation toolkit (GATE). An average full width at half maximum (FWHM) at different locations of 1.77 mm and 1.79 mm are obtained using the proposed system model and standard LOR system model, which does not include penetration effects, respectively. The standard deviation of the uniform region in the NEMA image quality phantom is 2.14% for the proposed method and 14.3% for the LOR system model, indicating that the proposed model out-performs the standard LOR-based model.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.2
• /
• pp.154-168
• /
• 2021

Various types of wooden relics are being unearthed following the full-scale excavation in Wolseong palace site, Gyeongju in Korea. In particular, a large number of relics were found in the moat surrounding the Wolseong Fortress. This study attempted to secure basic data on the shields of the Silla era through species identification, radiocarbon dating, and shape analysis of the two wooden shields excavated from the Wolseong moat. As a result of the radiocarbon dating, it was confirmed that the shields were made of wood procured in the period between the mid-4th century and the early 5th century. The species identification confirmed that the body of the relic was made with Pinus soft pine group and the handle with Zelkova serrata. It was also confirmed that the excavated wooden shield was made by first marking a thin line on a flat grain board, then marking double concentric circles and perforating small holes. The distance between the division lines is constant at about 6cm, and spaces between them are colored in red and black. The shape analysis estimated that two artifacts were more than 50cm and 36cm in width, respectively.

• Design & Manufacturing
• /
• v.15 no.4
• /
• pp.65-71
• /
• 2021

In the early days of laser invention, it was simply used as a measuring tool, but as lasers became more common, they became an indispensable processing tool in the industry. Short-wavelength lasers are used to make patterns on wafers used in semiconductors depending on the wavelength, such as CO2 laser, YAG laser, green laser, and UV laser. At first, the hole of the PCB board mainly used for electronic parts was not thin and the hole size was large, so a mechanical drill was used. However, in order to realize product miniaturization and high integration, small hole processing lasers have become essential, and pattern exposure for small hole sizes has become essential. This paper intends to analyze the characteristics through patterns by exposing the PCB substrate through DMD and polygon scanner, which are different optical systems. Since the optical systems are different, the size of the patterns was made the same, and exposure was performed under the optimal conditions for each system. Pattern characteristics were analyzed through a 3D profiler. As a result of the analysis, there was no significant difference in line width between the two systems. However, it was confirmed that dmd had better pattern precision and polygon scanner had better productivity.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.23 no.4
• /
• pp.57-71
• /
• 2021

The purpose of the study is to derive an appropriate knitting method that can increase the appearance, wearability, and functionality through empirical research on the sleeve height knitting ratio of seamless knit wear. The study was conducted by producing seven types of experiment clothes according to knitting ratio to examine the characteristics according to the body armhole and sleeve height ratio. Specifically, after fit evaluatins, variance analysis (ANOVA) was performed to analyze the results of the evaluation, and the evaluated contents were converted into data. Among them, the items with significant results were intensively studied using the Duncan-test. The result showed that the height and the width of the sleeves vary depending on the knitting ratio. Test sweater A was the highest at 16cm, followed by test sweater B, test sweater C, test sweater D, test sweater E, test sweater F, and test sweater G at 4cm. The 1:1 ratio of test sweater A, was the highest, which is knitted in the same course as the body. The larger the difference in the ratio of body and sleeve, the lower the height of the sleeves. As a result of the appearance sensory evaluation, a significant difference was confirmed in the result values (p<0.001) from all items on the front, side, and rear. Specifically, the appearance of the test sweater B(2:4:2) on the front and test sweater C(2:4:3) on the side and rear side was the best. When the sleeves height is properly set, the ratio of the arm line to fit the design with a natural curve is analyzed as a very important factor. The results of this study are expected to be of practical use in product development and production that can increase the feeling when wearing and design satisfaction.

• Geomechanics and Engineering
• /
• v.25 no.3
• /
• pp.179-194
• /
• 2021

In this paper, to study the stability of surrounding rock during roadway excavation in different rock mass structures, the physical model test for roadway excavation process in three types of intact rock mass, layered rock mass and massive rock mass were carried out by using the self-developed two-dimensional simulation testing system of complex underground engineering. Firstly, based on the engineering background of a deep mine in eastern China, the similar materials of the most appropriate ratio in line with the similarity theory were tested, compared and determined. Then, the physical models of four different schemes with 1000 mm (height) × 1000 mm (length) × 250 mm (width) were constructed. Finally, the roadway excavation was carried out after applying boundary conditions to the physical model by the simulation testing system. The results indicate that the supporting effect of rockbolts has a great influence on the shallow surrounding rock, and the rock mass structure can affect the overall stability of the surrounding rock. Furthermore, the failure mechanism and bearing capacity of surrounding rock were further discussed from the comparison of stress evolution characteristics, distribution of stress arch, and failure modes in different schemes.

• Particle and aerosol research
• /
• v.18 no.4
• /
• pp.129-136
• /
• 2022

The line width of circuits in semiconductor devices continues to decrease down to a few nanometers. Since nanoparticles attached to the patterned wafer surface may cause malfunction of the devices, it is crucial to remove the contaminant nanoparticles. Physical cleaning that utilizes momentum of liquid for detaching solid nanoparticles has recently been tested in place of the conventional chemical method. Dropwise impaction has been employed to increase the removal efficiency with expectation of more efficient momentum exchange. To date, most of relevant studies have been focused on drop spreading behavior on a horizontal surface in terms of maximum spreading diameters and average spreading velocity of drop. More important is the local liquid velocity at the position of nanoparticle, very near the surface, rather than the vertical average value. In addition, there are very scarce existing studies dealing with microdroplet impaction that may be desirable for minimizing pattern demage of the wafer. In this study, we investigated the local velocity distribution in spreading liquid film under various impaction conditions through the CFD simulation. Combining the numerical results with the particle removal model, we estimated an effective cleaning diameter (ECD), which is a measure of the particle removal capacity of a single drop, and presented the predicted ECD data as a function of droplet's velocity and diameter particularly when the droplets are microns in diameter.

• The Korea Journal of Herbology
• /
• v.34 no.1
• /
• pp.33-42
• /
• 2019

Objectives : This study aimed to be used as basic data for obtaining excellent quality of Salvia miltiorrhiza (SM) root. Methods : SM cultivated in Anhui Bozou, Henan, Shandong, Henan Wenxian, Zhejiang, Hebei, Liaoning, Shanxi, Shaanxi Shangluo, Sichuan Zhongjiang, Sichuan Minyang and Jiangsu in China were gathered and its internal morphology and physicochemical patterns were analyzed. Results : Cross-section of sang plants according to cultivated regions in China showed that cork layers consisted of cells with four to six layers, cortex width was wide, and phloem was semilunar-shaped. Although there are forms layers, yet boundary was vague. It was observed that eight to ten vascular bundles were arranged in wooden parts in all directions and as a single line of vascular was distributed nearby form layers as it nears to the center. Tanshinon IIA identified a spot in the same location with standard product near by Rf 0.9 in the test identifying TLC of SM according to cultivated areas in China. The largest amount was 0.535% identified in Shandong and the lowest amount of 0.05% in Hebei. Salvianolic acid B identified a spot in the same location with standard product near by Rf 0.7 in the test identifying TLC of SM according to cultivated areas in China. The largest amount was 2.72% identified in Liaoning and the lowest amount of 0.825% in Jiangsu. Conclusions : The results are assumed to be used as basic data for obtaining excellent quality of SM oriental medical hers and distinguishing authentic or fake herbs.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.35-40
• /
• 2022

This paper proposes an antenna that is located outside the PCB substrate of an electronic product to enable wireless communication in the ISM band. The PCB designed the T-shaped OPEN-STUB power supply line to be miniaturized so that it does not interfere with parts or interfere with design. The characteristics of the antenna were confirmed in the 2.4GHz and 5.8GHz bands using a T-shaped stub feeder and a spiral structure. The size of the antenna is 5mm in width × 6.5mm in length, and the thickness of the PCB is 1.2T. As a result of measurement of the manufactured antenna, it was possible to obtain a return loss of -10dB or more at 2.4GHz and 5.8GHz. In the E-plane, the gain was -4.45 dBi, and in the H-plane, the gain was -1.05 dBi. Therefore, the proposed small antenna for wireless communication showed excellent performance.