• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2005년도 학술발표논문집
• /
• pp.108-112
• /
• 2005

In this research, the physical properties of fresh concrete using lime stone powder as a part of cement were investigated. Fresh concrete using lime stone powder was prepared with various lime stone powder replacement($5{\sim}12$ volume %) for cement and the quantities of sand aggregate ratio in concrete were 47.3%, 48.5% and 49.4% of ratio of sand aggregate. The workability, flowing characteristics, air content and bleeding of concrete using lime stone powder were tested and the results were compared with those of ordinary portland cement concrete. In the experiment, we acquired satisfactory results at the point of fresh concrete characteristics using lime stone powder within the replacement ratio of $8{\sim}12%$ and the optimum quantity of sand aggregate ratio in concrete was found to be $48.5%{\sim}50%$ of ratio of sand aggregate.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.287-292
• /
• 2001

This paper investigates the properties of high fluidity concrete incorporating lime stone powder and fly ash. Lime stone powder(LSP) and fly ash(FA) contents are varied with. According to test results, as LSP and FA contents increase, fluidity, air content and placeability shows a declining tendency. For the temperature history, both LSP and FA have favorable effects on reducing hydration heat, moreover, LSP reduces hydration heat more than FA. LSP shows undesirable strength loss as its content increases. FA also decreases the strength at early age, but it enhances later age strength. Accordingly LSP is expected to improve the quality at fresh concrete and reduce hydration heat, while it causes strength loss.

• 콘크리트학회논문집
• /
• 제26권3호
• /
• pp.277-285
• /
• 2014

이 연구는 현장에서 사용하는 재료의 품질 및 계량오차, 현장조건 등에 따라 병용계 자기충전 콘크리트의 유동특성에 영향을 미치는 변동요인의 범위를 실험적으로 규명하기 위한 것이다. 병용계 자기충전 콘크리트의 재료는 벨라이트 시멘트와 석회석 미분말을 사용한 벨라이트계 및 슬래그 시멘트와 석회석 미분말을 사용한 슬래그계가 선정되었으며, 선행연구에서 제시된 최적배합 조건을 대상으로 하였다. 변동요인으로 (1) 콘크리트의 온도 3종류, (2) 잔골재의 표면수율 5종류, (3) 잔골재의 조립률 5종류, (4) 고성능AE감수제의 사용량 5종류, (5) 석회석 미분말의 분말도 3종류 등을 대상으로 민감도 시험을 실시하였다. 민감도 시험의 항목은 슬럼프 플로우, 500 mm 플로우 도달시간, V-깔대기 유하시간, U-box 충전성 높이를 대상으로 하였다. 실험 결과, (1) 콘크리트 온도는 $10{\sim}20^{\circ}C$ 범위, (2) 잔골재의 표면수율은 ${\pm}0.6%$ 범위, (3) 잔골재의 조립률 $2.6{\pm}0.2$ 범위, (4) 고성능AE감수제의 사용량은 ${\pm}0.2%$ 범위, (5) 석회석 미분말의 분말도는 $6000cm^2/g$ 범위에서 현장품질을 관리해야 한다. 벨라이트계 및 슬래그계에 따른 차이는 크지 않았지만, 석회석 미분말 및 $C_2S$ 함량이 높은 벨라이트계가 안정적인 경향을 나타내었다. 따라서 이러한 결과를 현장 시공현장에서 병용계 자기충전 콘크리트의 관리방안으로 제안하고자 한다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.567-572
• /
• 2002

This research investigates experimentally an effect on the quality performances of the high flowing concrete according to binder types. The purpose of this study is to determine the optimum mix proportion of the high flowing concrete having good flowability, viscosity and no-segregation. For this purpose, two types using belite cement＋lime stone powder(LSP) and furnace slag cement+lime stone powder are selected and tested by design factors including water cement ratio, fine and coarse aggregate volume ratio. As test results of this study, the optimum mix proportion for binder types is as followings. 1) One type based belite cement ; water cement ratio $51^{\circ}C$, fine aggregate volume ratio $43^{\circ}C$ and coarse aggregate volume ratio $53^{\circ}C$, replacement ratio of LSP $42.7^{\circ}C$. 2) Another type based slag cement : water cement ratio $41^{\circ}C$, fine aggregate volume ratio $47^{\circ}C$ and coarse aggregate volume ratio $53^{\circ}C$, replacement ratio of LSP $13.5^{\circ}C$.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.584-587
• /
• 2004

This research investigates the rheological behavior and the confined water ratio of the cement paste and binder condition in order to predict mix design proportion of the high flowing concrete. The purpose of this study is to determine the optimum replacement ratio of binders including fly ash, and lime stone powder by the cement weight. For this purpose, belite cement, blast furnace slag cement and ordinary portland cement are selected. As test results, the confined water ratio shows the following range ; OPC>blast furnace slag cement>belite cement. Therefore, belite cement is proved very excellent cementitious materials in a view point of the flowability. The optimum replacement ratio of lime stone powder is shown over $30\%$ in case of belite cement and about $10\%$ in case of slag cement type. Also, the optimum replacement ratio of fly ash is shown $30\%$ by the cement weight considering the confined water ratio and deformable coefficient of the paste condition.

• KCI Concrete Journal
• /
• 제14권3호
• /
• pp.121-129
• /
• 2002

This study investigates experimentally into the design factors and quality variations having an effect on the properties of the combined high flowing concrete to be poured in the slurry wall of Inchon LNG in-ground receiving terminal. Especially, high belite cement and lime stone powder as cementitious materials and viscosity agent in order to improve self-compaction and hydration heat are used in this study. Water-cement ratio(W/C), fine aggregate volume ratio(Sr) and coarse aggregate volume ratio(Gv) as design factors of the combined high flowing concrete are applied to determine the optimum mix design proportion. Also quality variations for sensitivity test are selected items as followings. (1)Surface moisture(5cases) and (2)Fineness modulus of fine aggregate(5cases), (3)Concrete temperature(3cases), (4)Specific surface(3cases) and particle size of lime stone powder. As experimental results, water-cement ratio, fine and coarse aggregate volume ratio are shown as the optimum range 51%, 43% and 53% separately considering site condition of slurry wall. Also quality factors by sensitivity test should be controlled in the following ranges. (1) Surface moisture :to.67% and (2)Fineness modulus 2.6$\pm$0.2 of fine aggregate, (3)Concrete temperature l0-20t, (4) Specific surface 6,000$\textrm{cm}^2$/g and particle size 9.7$\pm$1.0${\mu}{\textrm}{m}$ of lime stone powder. Based on the results of this study, the optimum mix design proportion of the combined high flowing concrete are selected and poured successfully in the slurry wall of LNG in-ground tank.

• 한국건설순환자원학회논문집
• /
• 제6권3호
• /
• pp.118-125
• /
• 2011

콘크리트 내부의 공극의 크기 및 분포상태는 콘크리트의 내구성을 결정하는 요인 중 하나이며, 구조물의 성능을 판단하는데 중요한 지표로 사용된다. 최근 고유동 콘크리트(High-Fluidity Concrete 이하 HFC로 약함)에 대한 연구는 많은 시공사례와 함께 진행되고 있지만, 콘크리트의 내구성능에 영향을 미치는 공극구조에 대한 연구는 미비한 실정이다. 따라서 본 연구에서는 30 MPa 범위의 일반콘크리트(Conventional Concrete 이하 CC로 약함) 및 석회석 미분말 및 플라이 애시를 사용한 HFC를 제조하여 콘크리트의 공극구조를 비교 분석 하였다. 실험결과 30 MPa 범위의 CC 및 HFC의 평균 공극 직경은 HFC가 CC보다 작게 나타났으며, SEM 분석 결과 HFC가 CC보다 전체적으로 내부구조가 치밀한 것으로 나타났다. 이러한 결과를 통하여 HFC가 CC보다 내구성 측면에서 우수할 것으로 판단된다.

• 콘크리트학회논문집
• /
• 제17권2호
• /
• pp.293-302
• /
• 2005

This study describes data from determination of the optimum mix proportion and site application of the mass concrete placed in bottom slab and side wall having a large depth and section as main structures of LNG in-ground tank. This concrete requires low heat hydration, excellent balance between workability and consistency because concreting work of LNG in-ground tank is usually classified by under-pumping, adaptation of longer vertical and horizontal pumping line than ordinary pumping condition. For this purpose, low heat Portland cement and lime stone powder as cementitious materials are selected and design factors including unit cement and water content, water-binder ratio, fine aggregate ratio and adiabatic temperature rising are tested in the laboratory and batch plant. As experimental results, the optimum unit cement and water content are selected under $270kg/m^3$ and $l55{\~}l60 kg/m^3$ separately to control adiabatic temperature rising below $30^{\circ}C$ and to improve properties of the fresh and hardened concrete. Also, considering test results of the confined water ratio($\beta$p) and deformable coefficient(Ep), $30\%$ of lime stone powder by cement weight is selected as the optimum replacement ratio. After mix proportions of 5cases are tested and compared the adiabatic temperature rising($Q^{\infty}$, r), tensile and compressive strength, modulus of elasticity, teases satisfied with the required performances are chosen as the optimum mix design proportions of the side wall and bottom slab concrete. $Q^{\infty}$ and r are proved smaller than those of another project. Before application in the site, properties of the fresh concrete and actual mixing time by its ampere load are checked in the batch plant. Based on the results of this study, the optimum mix proportions of the massive concrete are applied successfully to the bottom slab and side wall in LNG in-ground tank.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.61-62
• /
• 2012

This study is for analyzing possibility of utilizing as cement from waste concrete. The scrapped fine powder which contains a large amount of hydrate of cement can supercede lime stone, and greenhouse gas reductions are expected. However, Fine Aggregate powder efficient separation technology development is essential for that limestone substitution effect and reduce greenhouse gas emissions in order to facilitate through the recycling of the scrapped fine powders.

• 동력기계공학회지
• /
• 제20권5호
• /
• pp.86-91
• /
• 2016

This paper is concerned chiefly with the method of porous foam manufacture using basalt stone powder sludge. The hydrogen peroxide($H_2O_2$) of bloating agent has lots of problems to manufacture porous lightweight aggregate due to fast reaction rate with cement or calcium hydroxide($Ca(OH)_2$). The $H_2O_2$ injecting method using nozzle for manufacturing porous lightweight aggregate is proposed, in this study. This method is to inject $H_2O_2$ at the pressure of 10 MPa on upper side of slurry mixing materials such as stone powder sludge and quick-lime(CaO) by injector. The specimen was dried in furnace at $100^{\circ}C$ for 1 hour and cured at ambient temperature for 30 days. We analyzed the characteristics including specific gravity and water absorption. The experiments were found that the porous foam has low specific gravity, high water absorption and uniform distribution of porous more than manufactured foam by general bloating methods.