• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.19 no.3
• /
• pp.213-232
• /
• 2009

This document was prepared to review and summarize the analytical methods for airborne and bulk asbestos. Basic principles, shortcomings and advantages for asbestos analytical instruments using phase contrast microscopy(PCM), polarized light microscopy(PLM), X-ray diffractometer (XRD), transmission electron microscopy(TEM), scanning electron microscopy(SEM) were reviewed. Both PCM and PLM are principal instrument for airborne and bulk asbestos analysis, respectively. If needed, analytical electron microscopy is employed to confirm asbestos identification. PCM is used originally for workplace airborne asbestos fiber and its application has been expanded to measure airborne fiber. Shortcoming of PCM is that it cannot differentiate true asbestos from non asbestos fiber form and its low resolution limit ($0.2{\sim}0.25{\mu}m$). The measurement of airborne asbestos fiber can be performed by EPA's Asbestos Hazard Emergency Response Act (AHERA) method, World Health Organization (WHO) method, International Standard Organization (ISO) 10312 method, Japan's Environmental Asbestos Monitoring method, and Standard method of Indoor Air Quality of Korea. The measurement of airborne asbestos fiber in workplace can be performed by National Institute for Occupational Safety and Health (NIOSH) 7400 method, NIOSH 7402 method, Occupational Safety and Health Administration (OSHA) ID-160 method, UK's Health and Safety Executive(HSE) Methods for the determination of hazardous substances (MDHS) 39/4 method and Korea Occupational Safety and Health Agency (KOSHA) CODE-A-1-2004 method of Korea. To analyze the bulk asbestos, stereo microscope (SM) and PLM is required by EPA -600/R-93/116 method. Most bulk asbestos can be identified by SM and PLM but one limitation of PLM is that it can not see very thin fiber (i.e., < $0.25{\mu}m$). Bulk asbestos analytical methods, including EPA-600/M4-82-020, EPA-600/R-93/116, OSHA ID-191, Laboratory approval program of New York were reviewed. Also, analytical methods for asbestos in soil, dust, water were briefly discussed. Analytical electron microscope, a transmission electron microscope equipped with selected area electron diffraction (SAED) and energy dispersive X-ray analyser(EDXA), has been known to be better to identify asbestiform than scanning electron microscope(SEM). Though there is no standard SEM procedures, SEM is known to be more suitable to analyze long, thin fiber and more cost-effective. Field emission scanning electron microscope (FE-SEM) imaging protocol was developed to identify asbestos fiber. Although many asbestos analytical methods are available, there is no method that can be applied to all type of samples. In order to detect asbestos with confidence, all advantages and disadvantages of each instrument and method for given sample should be considered.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.6 s.336
• /
• pp.31-38
• /
• 2005

In this paper, we proposed an optical security system based on a gray-image exclusive-OR encryption using multi-phase separation and phase-wrapping method. For encryption, a gray image is sliced into binary images, which have the same pixel value, and these images are encrypted by modified XOR rules with binary random images. The XORed images and the binary images respectively combined and converted into full phase images, called an encrypted image and a key image. For decryption, when the encrypted image and key image are used as inputs on optical elements, Practically due to limited controllability of phase range in optical elements, the original gray image cannot be efficiently reconstructed by these optical elements. Therefore, by decreasing the phase ranges of the encrypted image and key image using a phase-wrapping method and separating these images into low-level phase images using multi-phase separation, the gray image can be reconstructed by optical elements which have limited control range. The decrytion process is simply implemented by interfering a multiplication result of encrypted image and key image with reference light. The validity of proposed scheme is verified and the effects, which are caused by phase limitation in decryption process, is analyzed by using computer simulations.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.24 no.5
• /
• pp.417-424
• /
• 2006

Despite of many researches related to create 3D digital maps, it is still time-consuming and costly because a large part of 3D digital mapping is conducted manually. To circumvent this limitation, we proposed methodologies to create 3D digital maps with 3D symbols automatically. For this purpose, firstly, the 3D symbol library to represent 3D objects as 3D symbols was constructed. In this library, we stored the attribute and geometry information of 3D objects which define types and shapes of symbols respectively. These information were used to match 3D objects with 3D symbols and extracted from 2D digital maps and LiDAR(Light Detection and Ranging) data. Then, to locate 3D symbols into a base map automatically, we used predefined parameters such as the size, the height, the rotation angle and the center of gravity of 3D objects which are extracted from LiDAR data. Finally, the 3D digital map in urban area was constructed and the results were tested. Through this research, we can identify that the developed algorithms can be used as effective techniques for 3D digital mapping.

• Land and Housing Review
• /
• v.3 no.4
• /
• pp.343-355
• /
• 2012

The purpose of this paper is to propose reasonable improvements of demand estimation methods of commercial site through the case study. Thus, we investigated the problems and limitation of demand estimation methods and process applied to primary and secondary new towns in Korea. And we suggested the way to reduce error of demand estimation and to raise its objectivity. The result of case analysis is as follows; firstly, it was insufficient to consider location, hierarchy and change of land use like mixed-use development in commercial site. Secondly, improper comparable group or operated relevant index data in the same light were selected the aggregated unit requirement method such as comparative analogy method and planning guidelines. Thirdly, there were many cases that demand estimation value was amended arbitrarily, and it tends to occur a serious reliability problem. Therefore, to improve these problems and to make better use of demand estimation hereafter are required the sublation of arbitrary commercial sphere's settings, the making of comparative group considered development conditions, and putting forward objective revision basis.

• Journal of Plant Biology
• /
• v.2 no.1
• /
• pp.14-21
• /
• 1959

The bamboo, one of staples of South-East Asia, has 1, 250 species in 46 Genus throughout the world South-East Asia, it's main habitat, has 1, 180 species, while South America has about 70 species or so. Major places of it's production in Asia are Korea, southern China, Japan, Malay, Ceylon, Formosa, and Philipine, but of these, Korea, southern China, and Japan are the most famous places for their production of excellant bamboo. In Korea, Kyongsang-Namdo and Cholla-Namdo are known as it's home, occupying 80 per cent of the total area of bamboo production in this country. Kyongsang-Pukdo, Cholla-Pukdo, Chungehong-Namdo, and Kangwon-do are also known as it's minor production. The importance of the bamboo can not be ignored, considering it's role in the industrial development of this country; the bamboo-ware is indispensable for the culture of laver which annually secures a considerable amount of foreign money. But it has long been regreted that the home-made bamboo-ware is far from being able to meet the ever increasing demand in quantity and is forced to be imported annually. In the light of the above mentioned fact, much interested; I undertook the task of investigating the bamboo in this country, Primarily concerned in it's kind and distribution, and could draw the following conclusions as the first phase of my investigation: (1). The amount of the bamboo accumulation in this country, compared with that of pre-worldwar II, is reduced as much as 300, 000 fagots(on fagot amounts to 25 pieces), and now the acreage of the bamboo field is 32, 200$\textrm{km}^2$s. (2). At a mountian peak in Kunoe-myon Wando-kun Cholla-Namdo, I found out a new specis. (Shasamorpha chiisanensis NAKAI Forma wan-Ponia H. P. CHONG) (3). The kinds of the autogenous wild bamboo in this country are as follows; a). 8 kinds in Sinoarundinaria. (5 Spp; 2 For; 1 Var) b). 1 kinds in Pieioplastus. (1 Spp) c). 2 kinds in Pseudosasa. (1 Spp; 1Var.) d) 4 kinds in Sasamorpha. (2 Spp; 1 For.; 1 Var.) e). 4 kinds in Sasa. (4 Spp) In total there are nineteen(19) kinds of autogenous wild bamboo in this country. When adding to this thethirty five (35) species which the japanese has transplanted in Kyongsang-Namdo Forestry Expreimental stations, there are in all fifty four (54) spe ies in this country. (4). As for the distribution of the Northern limitation of the bamboo growing, I found that Sinoarundinaria nigra OHWI var, Henonis HONDA can be cultivated as for as Kosongkun, Kangwon-Do, andSinoarundinaria pubescens HONDA as for as Clung Chong Namdo, and Sinoarundinaria reticulata as far as chung Chong-Pukdo.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.45 no.1
• /
• pp.35-51
• /
• 2017

Street gardens, a series of streetscape improvement projects led by Seoul City Government, are initiated for the purpose of providing aesthetic satisfaction and mental refreshment to pedestrians. In order to investigate whether street gardens indeed promote the psychological health of the users, questionnaire surveys were conducted on three selected street gardens - at Gangnam-daero, Digital-ro, and Teheranro - and their comparison sites located on the same streets, which have a similar physical environment but without a street garden. The survey questionnaires, based on Attention Restoration Theory, were composed of Perceived Restorativeness Scale-11 with the eleven individual questions grouped into four categories: 'Fascination', 'Being away', 'Coherence', and 'Scope'. The survey questionnaires also ask about physical components that promote psychological improvement in the aforementioned categories. The collected data was analyzed with factor analysis, reliability analysis, and independent t-test. The results suggested that street gardens had a relatively positive effect on the psychological restorativeness of the users. In particular, they gave fascination and interest to the users. However, they did not offer a feeling of being away to the users, which revealed the limitation in the psychological improvement effect of street gardens. The physical components of the street garden that have led the psychological restorativeness effect were wooden bench, tree, and flower. This result corresponds to an extant theory that natural factors have a positive effect on the psychological restorativeness within a hardscape. This research will shed light on the planning and design guidelines for the street garden project.

• Clean Technology
• /
• v.14 no.2
• /
• pp.95-102
• /
• 2008

In order to choose alternative environmental-friendly cleaning agents, it is very important in the present point that the systematic selection procedures should be introduced and applied to the industry through the evaluation of their cleaning ability, environmental characteristics, and economical factors, and that the objective and effective evaluation methods of cleanliness should be established for the industry. Thus, a novel cleaning evaluation method utilizing optically stimulated electron emission (OSEE) among various methods of cleaning ability was studied in this study. The contaminants used in this cleaning experiments were flux, solder, grease, cutting oil, and mixed soil of 35% grease and 65% cutting oil. The cleaning agents developed or prepared in our laboratory were employed and their cleaning ability were comparatively evaluated by the OSEE, gravimetry and contact angle methods. The experimental results in this work showed that flux cleaning efficiency measured by the OSEE method was similar to that of the gravimetric method, but that the OSEE method could not be compared with gravimetric method for the case of solder or grease cleaning because the contaminants radiate or absorb ultra-violet light. In case of cutting oil cleaning, the gravimetric method indicated its limitation of cleaning efficiency of cutting oil since it showed cleaning efficiency of 100%, even though residual soil remaining on the substrate surface a little after its cleaning. The comparative experimental results of cleaning ability evaluated by the OSEE- and contact angle measurement methods showed that they were similar in case of cleaning of flux, mixed soil and cutting oil. It was judged that the contact angle measurement method could evaluate the cleaning ability more precisely than the OSEE method for cleaning solder and grease.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.3
• /
• pp.319-324
• /
• 2003

Statement of problem. Adhesives in dentistry playa major role in the success of restorative treatments. In the treatment of all ceramic restoration it is needed to find the adequate bond strength between enamel and dentin. Purpose. The purpose of this study was to evaluate shear bond strength of resin cement bonded to extracted human uncut enamel, cut enamel, and dentin in vitro. Material and methods. Ten freshly extracted anterior teeth without any previous restorative treatments were chosen. The extracted teeth were embedded in PMMA cold acrylic in the shape of a cylinder, 25 mm in diameter by 25 mm in height. The bonding system used was as follow: Uni-Etch (32% phosphoric acid), One-Step adhesive, Duolink resin cement. The specimens were acid etched and rinsed with water. Two layers of One-Step adhesive were coated with a disposable brush on the uncut enamel. VIP curing light at $500mV/cm^2$ was used to cure the adhesive. For cut enamel shear bond test, the specimen used for uncut enamel was further reduced approximately $0.3{\sim}0.5mm$ using a laminate preparation diamond bur (0.3 mm in depth). The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit SiC paper and cleaned with distilled water. The bonding procedure on the cut enamel was same as uncut enamel bonding procedure. For dentin bonding test, the specimen used for cut enamel was further reduced approximately $0.5mm{\sim}1.0mm$ using a laminate preparation diamond bur (0.5 mm in depth of diamond cutting). The amount of reduction was evaluated with the silicone mold. The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit silicon carbon paper and cleaned in distilled water. The bonding procedure on the dentin was same as uncut enamel bonding procedure. All samples were mounted and secured on the Ultradent shear bond test sample holder, and Ultradent restricted shear bond testing device was used with Universal Instron machine until fracture. Analysis of variance (ANOVA) test was performed comparing the result at P<0.05. Multiple comparison (Tukey) was used to compare each groups. Result. The result showed that the mean value in shear bond strength of resin cement bonded to uncut enamel, cut enamel and dentin were 27.04 Mpa, 30.25 Mpa and 26.39 Mpa with respect. Conclusion. Within the limitation of this study, the mean value of the shear bond strength of cut enamel was higher than those of uncut enamel or dentin. However there existed no statistical differences between three different human dentition substrates due to increased adhesive characteristics.

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.6 no.1
• /
• pp.133-160
• /
• 1984

The main purpose of the present study is to survey the major abstracting bulletins of national nature in Korea, to define such problem areas as lacunae, duplicates and limitation in coverage in the abstracting services currently available in Korea, and to make some suggestions for action for improving the abstracting services in the light of general principles and the tradition and situations unique to Korea. The major conclusions reached at this study are summarised as follows: (A) A new abstracting bulletin of general nature covering the whole field needs to be created in each of the following fields where no established abstracting service is available for the outcome of research and development activities in Korea. (1) Language (2) Religion (3) Art (4) Language (5) Literature (6) History (B) A new specialised abstracting bulletin needs to be created in each of the following fields of science where abstracting services limited in coverage are partially available. (a) Statistics (b) Sociology (c) political science (d) Public administration (e) Law (f) Folk lore (g) Military science (2) Pure sciences (a) Mathematics (b) Chemistry (c) Astronomy (d) Geology (e) Mineralogy (f) Life sciences (g) Botany (h) Zoology (3) Applied sciences (a) Agriculture (b) Architectural engineering (c) Mechanical engineering (d) Electrical engineering (e) Chemical engineering (f) Manufacturing industry (g) Domestic science (C) Publication of the abstracting bulletins suggested in (A) and (B) above may be ideally carried on by a qualified learned society established in the respective field. and should be financially supported by the public fund under the provisions of Art. 27 of the Research Promotion Act of 1979. (D) The current practice of adding the author's abstract and keywords to each of the records of the "Doctoral Theses in Humanities and Social Sciences" part of the" Catalogue of Doctoral and Master's Theses Submitted to the Universities in Korea" published by the National Assembly Library should be applied to all the other parts, i. e. to the parts of the "Master's Theses in Humanities and Social Sciences" and of the "Doctoral and Master's Theses in Natural Sciences': which will not only increase the Catalogue's use value but also discourage appearance of various theses abstracts of individual academic institutions such as the" Abstracts of the Doctoral and Master's Theses Submitted to Korea Advanced Institute of Science and Technology" which will in turn reduce inefficiency involved in the abstracting services at national level. (E) A general abstracting bulletin covering most part of the outcome of research and development activities in Korea other than that covered by the existing abstracts needs to be created to be temporarily. used till the abstracting journals suggested in this study will be fully available. A realistic way of having such a bulletin may be to expand the present coverage of "The Abstracts of the Reports of the Government-sponsored Projects" currently published by Korean Research Foundation.

• Journal of Technologic Dentistry
• /
• v.11 no.1
• /
• pp.71-81
• /
• 1989

This study was aimed for bettering productivity and technical level of the dental 1 aboratory, and helping the dental technician's benefits and rights, and then endowing them some belonged atmospher and stability on their post by Improving job- satisfaction and maintaining the transferability of one's post at a proper limitation. Therefore, 320 dental technicians extracted randomly from all the technicians working at 494 dental laboratories were subjected for this study. The approach to the study was a way through some postal questionaires executed from March 29, 1988 until May 4, the same year, in which total 254 technicians answered, showing 79% resp"nserate. responserate. The data-analysis was done by a model of the dental technician's transferability from their post, as considering Mobley's(1978)-model of post-transferability, and results through the study are as follows : 1. Satisfaction at a given post showed that the married is better than the unmarried(<0.05), and the experienced is better than the inexperienced(P<0.01). 2. Age, sex, educational experience, and one's service-duration did not affect significantly to the respondent's satisfaction on their post, statistically. 3. Satisfaction at a given post differed in adccordance with given conditions of one's post, i. e.,it stowed high when the monthly payment was good(P<0.05), and when too much duty on their job was given, it was the worst as shown in an example of the next order, too much