• Corrosion Science and Technology
• /
• v.20 no.5
• /
• pp.249-255
• /
• 2021

In this work, we proposed a facile method to fabricate the three-dimensional porous copper current collector (3D Cu CC) for a Si-dominant anode in a Li-ion battery (LiB). The 3D Cu CC was prepared by combining chemical etching and thermal reduction from a planar copper foil. It had a porous layer employing micro-sized Cu balls with a large surface area. In particular, it had strengthened attachment of Si-dominant active material on the CC compared to a planar 2D copper foil. Moreover, the increased contact area between a Si-dominant active material and the 3D Cu could minimize contact loss of active materials from a CC. As a result of a battery test, Si-dominant active materials on 3D Cu showed higher cyclic performance and rate-capability than those on a conventional planar copper foil. Specifically, the Si electrode employing 3D Cu exhibited an areal capacity of 0.9 mAh cm^-2 at the 300^th cycles (@ 1.0 mA cm^-2), which was 5.6 times higher than that on the 2D copper foil (0.16 mAh cm^-2).

• Bulletin of the Korean Chemical Society
• /
• v.23 no.8
• /
• pp.1144-1148
• /
• 2002

We prepared the polyaniline (Pani) film and powder by chemical polymerization and doping with different dopants and also investigated the capability of Li//polyaniline cells after assembling. The oxidation/reduction potentials and electrochemical reaction of Li//polyaniline cells were tested by cyclic voltammetry technique. The Li//Pani-HCl cells with 10% and 20% conductors show a little larger specific discharge capacities than that without conductor. The highest discharge capacity of almost 50 mAh/g at 100th cycle is also achieved. However, Li//Pani-LiPF6 with 20% conductor shows a remarkable performance of ~90 mAh/g at 100th cycle. This is feasible value for using as the positive electrode material of lithium ion secondary batteries. It is also proved that the powder type electrode of Pani is better to use than the film type one to improve the specific discharge capacity and its stability with cycle.

• Korean Journal of Materials Research
• /
• v.7 no.6
• /
• pp.529-535
• /
• 1997

Li ion전지용 LiMn$_{2}$O$_{4}$분말을 졸-겔법과 고상반응법으로 제조하여 분말의 특성과 전지의 특성을 비교하였다. 졸-겔법에 의해 제조된 LiMn$_{2}$O$_{4}$분말은 고상반응법에 의해 제조된 분말보다 낮은 온도에서 합성이 가능하고, 균질하고 작은 입자들로 구성되었으며, Li stoichiometry가 우수하여 전지의 방전용량이 크나 양이온 혼합도가 높아 전지의 내부저항이 크게 나타났다. 졸-겔법은 높은 Li stoichiometry와 균질한 입자 크기를 갖는 LiMn$_{2}$O$_{4}$분말 제조에 적당한 것으로 생각되며, 전지의 내부저항 문제는 분말의 하소온도와 냉각속도의 조절에 의해 가능할 것으로 판단된다.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.4
• /
• pp.173-177
• /
• 2002

Electrochemical characteristics of a graphite/lithium and a $LiCoO_2/lithium$ half cell and a $graphite/LiCoO_2$ full cell were analyzed using a GCSOC (gradual control test of the state of charge) technique. The IIE (initial intercalation coulombic efficiency), which represents lithium intercalation property of the electrode material, and the $lIC_s$ (initial irreversible capacity by the surface), which represents irreversible reaction between the electrode surface and the electrolyte were obtained from the GCSOC analysis. Linear-fittable capacity ranges of IIE of graphite and $LiCoO_2$ electrodes were 370 and 150 mAh/g, respectively, based on material weight. The value of lIE for graphite and $LiCoO_2$ electrodes were $93-94\%$ and $94-95\%$, respectively. The value of IICs for graphite and $LiCoO_2$ electrodes were 15-17 mAh/g and 0.3-1.7 mAh/g, respectively. The value of IIE for $graphite/LiCoO_2$ full cell, used GX25 and DJG311 as a graphite, was $89-90\%$ that lower than that for the half cells. Parameters of IIE and IICs can also be used to represent not only half cell but also full cell.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.60-67
• /
• 2014

The battery cells in lithium-ion battery pack assembled with high-capacity and high-power pouch cells, are commonly cooled with thin aluminum cooling plates in contact with the cells. For HEV/EV lithium-ion battery systems assembled with high-capacity, high-power pouch cells, the cells are commonly cooled with thin aluminum cooling plates in contact with the cells. Thin aluminum cooling plates are cooled by cold plate with coolant flow paths. In this study, the effect of the battery cooling system design including aluminum cooling plate thickness and various position of cold plate on the cooling performance are investigated by using finite element methods (FEM). Optimal cooling plate and cold plate design are proposed for improving the uniformity in temperature distributions as well as lowering average temperature for the cells with large capacities based on the simulation results.

• Journal of Electrochemical Science and Technology
• /
• v.4 no.1
• /
• pp.27-33
• /
• 2013

The consequences of electrode density and thickness for electrochemical performance of lithium-ion cells are investigated using 2032-type coin half cells. While the cathode composition is maintained by 90:5:5 (wt.%) with $LiCoO_2$ active material, Super-P electric conductor and polyvinylidene fluoride polymeric binder, its density and thickness are independently controlled to 20, 35, 50 um and 1.5, 2.0, 2.5, 3.0, 3.5 g $cm^{-3}$, respectively, which are based on commercial lithium-ion battery cathode system. As the cathode thickness is increased in all densities, the rate capability and cycle life of lithium-ion cells become significantly worse. On the other hand, even though the cathode density shows similar behavior, its effect is not as high as the thickness in our experimental range. This trend is also investigated by cross-sectional morphology, porosity and electric conductivity of cathodes with different densities and thicknesses. This work suggests that the electrode density and thickness should be chosen properly and mentioned in detail in any kinds of research works.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.8
• /
• pp.2571-2576
• /
• 2011

Surface film formation on $Li(Ni_{1/3}Co_{1/3}Mn_{1/3})O_2$ cathodes upon oxidation of electrolyte during electrochemical cycling was investigated. Information on the important factors for film formation on the cathode can facilitate the design of additives that improve the properties of the cathode. Pyrazole is added to the electrolyte because it is readily oxidized to form a surface film on the cathode. The results of differential scanning calorimetry and Fourier transform infrared spectroscopy (FTIR) showed that the active material played a dominant role in the interfacial film formation with the electrolyte. Carbon black played a negligible role in the surface film formation.

• Corrosion Science and Technology
• /
• v.21 no.4
• /
• pp.250-257
• /
• 2022

Transition metal sulfide materials have emerged as a new anode material for Li secondary batteries owing to their high capacity and rate capability facilitated by fast Li-ion transport through the layered structure. Among these materials, niobium disulfide (NbS₂) has attracted much attention with its high electrical conductivity and high theoretical capacity (683 mAh g^-1). In this study, we propose a facile synthesis of Fe_xNbS₂/C composite via simple ball milling and heat treatment. The starting materials of FeS and Nb were reacted in the first milling step and transformed into an Fe-Nb-S composite. In the second milling step, activated carbon was incorporated and the sulfide was crystallized into Fe_xNbS₂ by heat treatment. The prepared materials were characterized by X-ray diffraction, electron spectroscopies, and X-ray photoelectron spectroscopy. The electrochemical test results reveal that the synthesized Fe_xNbS₂/C composite electrode demonstrates a high reversible capacity of more than 600 mAh g^-1, stable cycling stability, and excellent rate performance for Li-ion battery anodes.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.2
• /
• pp.127-132
• /
• 2024

Recently, secondary batteries, commonly known as rechargeable batteries, find widespread applications across various industries. Particularly valued for their compact and lightweight characteristics, they play a crucial role in diverse portable electronic devices such as smartphones, laptops, and tablets, offering high energy density and efficient charge-discharge capabilities. Moreover, they serve as vital components in electric vehicles and contribute significantly to the field of renewable energy as part of Energy Storage Systems(ESS). However, despite advancements in this technology, issues such as reduced lifespan, cracking, damage, and even the risk of fire can arise due to excessive charging and discharging of secondary batteries. To address these challenges, Battery Management System(BMS) are employed to protect against overcharging and improve overall performance. Nevertheless, understanding the protective range settings of BMS using lithium-ion batteries, the most commonly used secondary batteries, and lead-acid batteries can be challenging. Therefore, this paper aims to utilize a battery charge-discharge tester and simulator to investigate the charging and discharging characteristics of lithium-ion batteries and lead-acid batteries, addressing the associated challenges of reduced lifespan, cracking, damage, and fire hazards in secondary batteries.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.240-244
• /
• 2001

Recycling process involving mechanical, thermal, hydrometallurgical, and sol-gel step has been applied to recover cobalt and lithium from spent lithium ion batteries and to synthesize LiCoO$_2$from leach liquor as cathodic active materials. Electrode materials containing lithium and cobalt could be concentrated with 2-step thermal and mechanical treatment. Leaching behaviors of the lithium and cobalt in nitric acid media was investigated in terms of reaction variables. Hydrogen peroxide in 1 M HNO$_3$solution turned out to be an effective reducing agent by enhancing the leaching efficiency. O f many possible processes to produce LiCoO$_2$, the amorphous citrate precursor process (ACP) has been applied to synthesize powders with a large specific surface area and an exact stoichiometry. After leaching used LiCoO$_2$with nitric acid, the molar ratio of Li/Co in the leach liquor was adjusted at 1.1 by adding a fresh LiNO$_3$solution. Then, 1 M citric acid solution at a 100% stoichiometry was also added to prepare a gelatinous precursor. When the precursor was calcined at 95$0^{\circ}C$ for 24 hr, purely crystalline LiCoO$_2$was successfully obtained. The particle size and specific surface area of the resulting crystalline powders were 20 пm and 30 $\textrm{cm}^2$/g, respectively The LiCoO$_2$powder was proved to have good characteristics as cathode active materials in charge/discharge capacity and cyclic performance.