• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.6
• /
• pp.97-107
• /
• 2013

On the Staggered Crosswalks, pedestrians cross the crosswalks two times. This method can reduce the cycle, the vehicle delay and the walking distance by increasing the major direction of green time. The safety of pedestrians is also effective. This study suggests the warrant of the facilities of island width and length etc. by considering the road structure and pedestrians. Also this study suggests the standard of the safety through the accident analysis of Staggered crosswalks and General Crosswalks. In the results, accident rate of the Staggered Crosswalks 18.3(100 million vehicle-km) was lower than the accident rate of the General Crosswalks 28.3(100million vehicle-km). By understanding the start point of crossing of the Staggered Crosswalks, the analysis of the location and types of accident suggests the safety zone(spare space). The setting warrants of Staggered Crosswalks are 4 lane over the road and the 2 meter over sidewalk width of island. The minimum length of the Pedestrian island was doubled compared to the crosswalks width. And the maximum length was set by considering the wait time of the pedestrians.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.45-54
• /
• 2009

Despite vehicle instability problems caused by gusts of wind on freeways located in mountain or seaside areas, current national highway design standards overlook their detrimental effects, and if higher design speed freeways being proposed now by the government are in operation, the strong effect of the gust of wind becomes a highway alignment design issue. This paper presents the vehicle movements and their resulting safety effects by checking vehicle sliding and overturn based on vehicle dynamic analysis for the case when a gust of wind blows to vehicles negotiating curves on higher speed freeways. In this analysis, vehicle types, curve radii, motorist responsive time to vehicle driving path changes, and vehicle speeds are systematically arranged to get vehicle sliding and overturn values in each different conditions. The results showed that there were little overturn possibilities when wind speed would stay in 50m/sec with higher than 600 meter curve radii. Interestingly it was also found in sliding checks that, although being safe at less than 15.0m/sec wind speed levels, there appeared the need of vehicle travel prohibitions when the wind speed could exceed 25.0m/sec level. The findings in this research is of information in future higher speed freeway designs, and particularly useful when designing freeways passing frequent gust wind areas.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.37 no.4
• /
• pp.429-437
• /
• 2010

The aim of this study was to evaluate the fluoride release and microhardness of Beautifil II as giomer(Group I), F2000 Compomer as compomer(Group II), GC Fuji II LC Capsule as resin-modified glass ionomer(Group III) and $Filtek^{TM}$ Z350 as composite resin(Group IV) according to time. Forty discs(5 mm diameter and 2 mm height) were prepared for each material. Each disc was immersed in 3 ml of de-ionized water within polyethylene tube and stored at $37^{\circ}C$. Evaluations were performed by pH/ISE meter for analysis of fluoride release and hardness testing machine for analysis of microhardness over 31 days. The results can be summarized as follows : 1. For all groups except group IV, the greatest fluoride release was observed after the first day of the study period and then dramatically diminished over time. On the 7th day of the study period, fluoride release level was stabilized. 2. Group III showed the highest fluoride release among test groups and then group II, group I were followed. Significant difference in cumulative fluoride release over 31 days was found between each groups. Group IV showed no fluoride release during study period. 3. Group IV showed the highest microhardness among test groups and then group I, group II, group III were followed. Significant difference in microhardness was found between each group, except between group I and group II. 4. After 31 days, microhardness was slightly diminished in every group. However, no significant difference was found.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.242-254
• /
• 2016

This paper is the forth investigation on the evaluation methods of flow characteristics in a steady flow bench. In the previous works, it was concluded that the assumption of the solid rotation might cause serious problems and both of the eccentricity and the velocity profile distort the flow characteristics when using the ISM at 1.75B plane. Also particle image velocimetry (PIV) measurement at this position showed that the real velocity profile was far from the assumption of ISM evaluation. In this paper, the planar velocity profiles were measure from 1.75B to 6.00B position by PIV and the characteristics were examined according to the valve angles and lifts for further investigations about the effect of the position on the velocity profile. The results show that $26^{\circ}$ valve angle is always an unique exceptional case in all aspects. If the valve angle is $21^{\circ}$ and below, the planar velocity profiles according to the lift and the position are similar to each other, however, the tangential velocity curves along with the radial direction have common tendencies up to $16^{\circ}$ angle. Also the well arranged swirl behaviors are generally observed at the position above 3.00B and the velocity contour lines come closer to the concentric circle as the valve lift increases. In addition, the gradient of tangential velocity along with the radial direction from the swirl center becomes stable and constant as the position goes downstream. Concurrently the velocity gradient is larger to the eccentric direction of the center. In the meantime the tangential velocity curves along with the radial direction are irregular and various at 1.75B, however, they become regular and reach higher level as the evaluation position goes downstream. At this time the curves of 4.50B are the best fitted to the ideal one. On the other hand in an exceptional case, $26^{\circ}$, the velocity contours are very complicated over 6mm valve lift regardless the position and the gradient increases to the opposite direction of the eccentric center. Also, 6.00B is a best fitting position in the geometrical cylinder center base. With respect to the swirl center, the distribution range of centers for 1.75B is different to that for the other positions and the eccentricities of this plane are larger regardless the valve angle. After 1.75B, there is no certain tendency in the center position change according to the valve angle and lift. Additionally, the eccentricities are not sufficiently small to neglecting the effect on ISM measurement.

• Journal of Animal Environmental Science
• /
• v.12 no.1
• /
• pp.21-28
• /
• 2006

This study was carried out to measure and analyze the characteristics of noise and vibration, and to analyze their effects on the productivity of layers, mechanical troubles, and abnormal wear-out failure of facilities and equipment of the layer house. The measurements of noise and vibration were taken at 13 layer farms nationwide for the operations of feed supplier system, feed distribution system, automatic egg collection system, ventilation system, blot conveyer for layer feces, and fur the case of with and without their operation by a sound level meter and a vibration measuring system in the layer house equipped with upright multi-tier cages. Measurement results showed that normal times were noise(N) 82 dB and vibration(V) 0.2072 cm/s, feed supplier system were 90 dB(N) and 2.8560 cm/s(V), feed distribution system were 90 dB(N) and 2.0222 cm/s(V), automatic egg collection system were 87 dB(N) and 0.1865 cm/s(V), ventilation system 88 dB(N) and 2.5364 cm/s(V), belt conveyer fur layer feces were 88 dB(N) and 0.2387 cm/s(V), and then maximum values of noise and vibration were 90 dB and 2.8560 cm/s, respectively, when feeding systems(feed supplying system and feed distribution system) were operated. Based on these results, an experiment is being conducted to find out the effect of noise and vibration on the productivity of layers in the layer house equipped with upright multi-tier cages.

• Korean Journal of Remote Sensing
• /
• v.31 no.3
• /
• pp.227-244
• /
• 2015

Synthetic Aperture Radar is able to provide images of wide coverage in day, night, and all-weather conditions. Recently, as the SAR image resolution improves up to the sub-meter level, their applications are rapidly expanding accordingly. Especially there is a growing interest in the use of geographic information of high resolution SAR images and the change detection will be one of the most important technique for their applications. In this paper, an automatic threshold tracking and change detection algorithm is proposed applicable to high-resolution SAR images. To detect changes within SAR image, a reference image is generated using log-ratio operator and its amplitude distribution is estimated through K-S test. Assuming SAR image has a non-gaussian amplitude distribution, a generalized thresholding technique is applied using Kittler and Illingworth minimum-error estimation. Also, MoLC parametric estimation method is adopted to improve the algorithm performance on rough ground target. The implemented algorithm is tested and verified on the simulated SAR raw data. Then, it is applied to the spaceborne high-resolution SAR images taken by Cosmo-Skymed and KOMPSAT-5 and the performances are analyzed and compared.

• Journal of Oral Medicine and Pain
• /
• v.15 no.1
• /
• pp.27-35
• /
• 1991

In order to evaluate muscular activity patterns of masticatory muscles and asymmetry patterns of muscular activity according to the levels of occlusal force, twenty-one individuals of age ranged from 23 to 27 years were examined. They were selected according to the following criteria : 1) no symptoms of temporomandibular disorder, 2) complete dentition except third molars, 3) normal or Angle's class I molar relationship and 4) no experience of dental treatment. The electromyographic amplitudes was measured for evaluation of muscular activity and asymmetric patterns of masseter and anterior temporal muscle during unilateral clenching at the levels of 10%, 20%, 40% and 50% of the maximum occlusal force by use of electromyogram and bite force meter. The obtained results were as follows : 1. The muscle activity indices of masticatory muscles of clenching side at the clenching levels of 10%, 20% and 30% of the maximum occlusal force were -19.12, -9.87, -0.49%, so that activity of anterior temporal muscle was dominant than that of masseter muscle. At the levels of 40%, 50% of the maximum occlusal force, muscle activity indices were 4.68%, 6.70%, so that activity of masseter was dominant at all level and as the levels of occlusal force was increased, muscular activity index was tend to decrease. 2. In masseter, asymmetry indices of muscular activity at the levels of 10%, 20% of maximum occlusal force were -10.34 and -1.24%, so that muscular activity of non-clenching side were dominant and at the levels of 30%, 40% and 50% each of maximum occlusal force, muscular activity was dominant on clenching side as 4.68, 7.18 and 10.9%. In anterior temporal muscle, asymmetry indices were 33.38%, 25.46, 2095, 10.23 and 15.45% at the levels of 10%, 20%, 30%, 40% and 50% each of maximum occlusal force, so that activity of clenching 15.45% at the levels of 10%, 20%, 30%, 40% and 50% each of maximum occlusal force, so that activity of clenching side was dominant than that of non-clenching side at all levels, but as the levels of occlusal force was increased, asymmetry indices of muscular activity was tend to decrease. 3. Between both sides, average electromyographic amplitudes of masseter and anterior temporal muscle were correlated, so that as the levels of occlusal force was increased, average electromyographic amplitudes of both side in same muscle were increased proportionally. But asymmetry indices between muscular activities of masseter and anterior temporal muscle were not correlated.

• Journal of the Korean Society of Food Culture
• /
• v.20 no.4
• /
• pp.433-437
• /
• 2005

The characteristic properties of rice breads produced from several conditions were investigated. The rice bread made in control condition (wheat flour), RF 3 (rice and wheat flour mixing) condition and RF 1 (rice, gluten and modified starch mixing) showed relatively higher volumethan others. The crust and crumb color were measured by Humter colory meter. The rice breads making on RF 5 and RF 6 condition showed higher crust L-value and the crumb L-value of the bread from RF 1 condition was higher than that from other condition. On the texture measuring by texture analyzer, hardness of the bread made from RF 1 and RF 2 conditions and cohesiveness of that from RF 3 condition were lower than control. However the significant higher level of the springiness and chewiness were showed in the bread from RF 1, RF 2 and RF 3 condition. The bread containing 85% of rice, 5% of rice, 5% of gluten and 10% of modified starch which was made in RF 1 condition obtained significant high overall acceptance score by sensory evaluation.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.8 no.3
• /
• pp.158-163
• /
• 2005

The purpose of this study was to observe the effect on the marine environment by the use of Nano-S. Nano-S was made to apply to improve the red tide bloom. The experiment was performed at round tank with volume of 180 L. Each tank was filled with an aggravated sediment about $14{\pm}1cm$ hight and sea water. The water flow-rate of tank was established on the rate of 6.25 L/hr. Sea water level was fitted to 40 cm, therefore the filled water was about 150 L. The sediment was stabilized during one week. Then the Nano-S and the red mud were added into each tank 0 kg(control), 1 kg(tank A), 2 kg(tank B), 5 kg(tank C) and 10 kg(tank D) each other. The quantity was fulfilled with 0 kg(control), 2.75 kg(tank A), 5.51 kg(tank B), 13.77 kg(tank C) and 27.55 kg(tank D) per square meter of sediment. The experiment was performed during 30 days. Water and sediment samples were collected from each tanks on the before 1hour and after 1, 3, 6, 12 hour and 1st, 3th, 5th, 7th, 10th, 15th, 30th day of the experiment period. The change of water and sediment quality was analyzed before and after applying the Nano-S and the red mud.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.89-101
• /
• 2001

The conventional pattern-methods for discrimination of acupoint, meridian line which is the basic object of diagnosis and medical treatment in oriental medicine is discriminated the conduction point by the stimulation in body skin with DC. But, it is not sufficient to truth in discrimination ratio, coincident ratio, body effect, reproductivity. Therefore, this paper is extracting the optimal parameter of frequency and waveform in order to improve the conventional pattern, and proposing the SPAC(Single Power Alternative Current) stimulus pattern applying that. Also, this algorithm proposes to be able to discriminate with low pressure of the electrode by displaying in the level meter both the absolution and relation value of the skin current. It is able to decrease pain and body effect by electrode pressure and discriminate acupoint regardless of skin current in difficult discrimination spot. It is compared the performance of system applying the extracted optimal parameter and algorithm, and it is confirmed that there is difference in discrimination parameter of acupoint reacted to the individual and the meridian. It is compared that discrimination, coincident ratio of the traditional acupoints as the acupoint stimulation pattern. It is confirmed truth of optimal parameter and discrimination algorithm. Keyword: Meridian, Discrimination, Coincident, Body effect, Reproductivity, SPAC, Optimal parameter.