• 한국정밀공학회지
• /
• 제20권11호
• /
• pp.108-116
• /
• 2003

In this paper, based on the concept of solid particles' sediment problem the working formula determining the bowl length of a Decanter-type centrifuge were derived. Assuming that particles are uniformly distributed along the vertical line of the liquid inlet position, it was possible to derive a constant value k used for determining the bowl length. It was shown from the sample calculations that the bowl length should be increased as the particle size to be removed from the liquid is decreased. The length also should be increased for the same particle size as the bowl diameter is decreased. To help the engineers choose a reasonable bowl diameter, the statistical relationship between the bowl diameter and the capacity of the international products is obtained and presented.

• 한국정밀공학회지
• /
• 제23권3호
• /
• pp.171-178
• /
• 2006

The sonication mettled is widely used with surfactants to suspend individual single-walled carbon nanotubes in solution, and it is well known that sonication-induced tube cutting occurs. Recently, it is found out that ultrasonicated nanotubes yield simultaneous separation by tube length and diameter. Nanotubes that have been cut shortest possess the greatest enrichments of large-diameter species. In this study, single-walled carbon nanotubes are cut using a ball milling method. Similar fracture behavior is observed fur the ball milled nanotubes: i.e., large diameter tubes are cut shorter. The ability to separate carbon nanotubes by diameter and length will contribute to tile development of nanotube-based applications.

• The Journal of Advanced Prosthodontics
• /
• 제15권6호
• /
• pp.302-314
• /
• 2023

PURPOSE. The aim of this study was to classify the shapes of retromolar pads and assess their morphometric differences using a 3D model. MATERIALS AND METHODS. Two hundred fully edentulous or Kennedy Class I partially edentulous patients (400 retromolar pads) were enrolled. Scan data of the definitive mandibular casts produced through functional impressions were obtained using a 3D laser scanner. Seven parameters (transverse diameter, longitudinal diameter, transverse-contour length, longitudinal-contour length, longitudinal/transverse diameter ratio, longitudinal/transverse-contour length ratio, and angle of the retromolar pad line to the residual alveolar ridge line) were measured using image analysis software. Subsequently, the pads were classified according to the shape. Statistical analyses were performed using 95% confidence intervals. RESULTS. Classifying the retromolar pads into three shapes led to high intra-examiner reliability (Cronbach's alpha = 0.933). The pear shape was the most common (56.5%), followed by oval/round (27.7%) and triangular (15.8%) shapes. There were no significant differences between the left and right sides according to the shape and no significant differences in any parameter according to age. The transverse diameter and longitudinal/transverse diameter ratio differed between sexes (P < .05). The triangular shape had a significantly different transverse diameter, transverse-contour length, longitudinal/transverse diameter ratio, and longitudinal/transverse-contour length ratio compared with the pear and oval/round shapes (P < .05). CONCLUSION. From a clinical reliability standpoint, classifying retromolar pads into three shapes (oval/round, pear-shaped, and triangular) is effective. The differences in the sizes among the shapes were attributed to the transverse measurement values.

• Structural Engineering and Mechanics
• /
• 제81권2호
• /
• pp.243-258
• /
• 2022

In this paper, tensile behavior of joint filling has been investigated under experimental test and numerical simulation (particle flow code). Two concrete slabs containing semi cylinder hole were prepared. These slabs were attached to each other by glue and one cubic specimen with dimension of 19 cm×15 cm×6 cm was prepared. This sample placed in the universal testing machine where the direct tensile stress can be applied to this specimen by implementing a special type of load transferring device which converts the applied compressive load to that of the tensile during the test. In the present work, two different joint filling thickness i.e., 3 mm and 6 mm were prepared and tested in the laboratory to measure their direct tensile strengths. Concurrent with experimental test, numerical simulation was performed to investigate the effect of hole diameter, length of edge notch, filling thickness and filling length on the tensile behavior of joint filling. Model dimension was 19 cm×15 cm. hole diameter was change in four different values of 2.5 cm, 5 cm, 7.5 cm and 10 cm. glue lengths were different based on the hole diameter, i.e., 12.5 cm for hole diameter of 2.5 cm, 10 cm for hole diameter of 5 cm, 7.5 cm for hole diameter of 7.5 cm and 5 cm for hole diameter of 10 cm. length of edge notch were changed in three different value i.e., 10%, 30% and 50% of glue length. Filling thickness were changed in three different value of 3 mm, 6 mm and 9 mm. Tensile strengths of glue and concrete were 2.37 MPa and 6.4 MPa, respectively. The load was applied at a constant rate of 1 kg/s. Results shows that hole diameter, length of edge notch, filling thickness and filling length have important effect on the tensile behavior of joint filling. In fixed glue thinks and fixed joint length, the tensile strength was decreased by increasing the hole diameter. Comparing the results showed that the strength, failure mechanism and fracture patterns obtained numerically and experimentally were similar for both cases.

• 터널과지하공간
• /
• 제21권5호
• /
• pp.386-393
• /
• 2011

본 연구에서는 암반 내 원통형 공동면에 나타나는 절리선 길이분포를 이용하여 암반 내에 존재하는 절리의 직경분포를 추정하기 위한 알고리듬을 제안하였다. 암반 내 절리의 직경분포를 추정하기 위해서 송재준(2005)에 의해 제시된 Joint Center Volume(JCV)의 개념이 적용되었다. 평면 조사창에 나타나는 절리선에 대한 JCV 값을 산정하는 송재준(2005)의 알고리듬을 확장하여, 원통형 공동면을 조사창으로 하는 경우의 암반 내 절리 직경분포 추정을 위해 전수조사 기법을 적용한 JCV 계산 알고리듬을 개발하였다. 추정된 절리 직경분포는 Monte-Carlo 시뮬레이션 기법을 이용하여 절리직경 모분포와 비교 검증하였으며 추정된 절리 직경분포가 모분포와 20% 내외의 오차 범위에서 수렴하는 것을 확인하였다.

• 대한치과기공학회지
• /
• 제28권2호
• /
• pp.347-353
• /
• 2006

The Purpose of this study was to compare the distribution of implant fixtures according to length and diameter between screw-retained and cement-retained implant-supported fixed prosthesis and to asses whether prosthesis retained types affected the selection of size of implant fixtures. This study presents a follow-up 2,416 implant-supported fixed type prosthesis that have been screw retained or cemented retained for about 10 years in 14 dental clinics. Included in the study were 458 men and 397 women and implant fixtures used in this study were screw retained type 1,057 and 1,359 of cemented retained type. The statistical results among the diameter types of fixture by prosthesis retained type was no significant difference noted (P= 0.809) and there was significant differences was enough to among the lengths of fixture by prosthesis retained type (P= 0.020). However there were no significant difference among the fixture diameter types and length by prosthesis retained type (P= 0.486). So there was not affected to prostheis fixation mechanism for the size of implant fixtures.

• 대한환경공학회지
• /
• 제33권5호
• /
• pp.359-367
• /
• 2011

압력수 확산공정은 정수공정에서 응집제나 염소용해수를 고압의 압력수로 분사하여 혼합하는 공정이다. 본 연구의 목적은 압력수 확산공정에 대한 전산유체역학적(Computational Fluid Dynamics) 진단을 통해 투입한 약품의 완전 혼합거리 및 혼합 거리를 줄이기 위한 확산판의 크기와 설치거리를 도출하는 것이다. 진단결과 2,200 mm 대형관에 $5kg/cm^2$ 압력수를 50mm, 100 mm 분사관으로 분사할 경우 혼합이 완료되는 혼합거리는 4D였다. 혼합거리를 줄이기 위해 분사관 전방에 확산판을 설치할 경우 분사관이 50 mm일 때 0.1D 직경의 확산판을 분사관 전방 0.2D 거리에 설치하면 혼합거리를 3D로 줄일 수있다. 그러나 분사관이 100 mm인 경우는 확산판의 크기와 설치 거리와는 상관없이 확산판이 없는 4D보다 확산거리를 줄일 수 없는 것으로 진단되었다. 따라서 2,200 mm 관에 압력수를 분사하는 경우는 50 mm 분사관을 설치하는 것이 100 mm보다 훨씬 효율적인 것으로 나타났다.

• 생물환경조절학회지
• /
• 제12권2호
• /
• pp.101-105
• /
• 2003

양파 plug묘 육묘시 일장조절에 의한 우량묘 생산을 위해 자연일장을 대비로 하여 11.5시간, 12.5시간 및 13.5시간의 일장 하에서 월륜과 창녕대고 품종을 200공 plug tray에 육묘한 후에 직경 16cm pot에 이식하여 16시간의 일장 하에서 재배하였다. 엽수, 엽초경, 초장 및 엽초장은 시기가 경과할수록 증가하였으나 13.5시간 일장에서의 초장과 엽초경은 일장처리 20일 후에는 감소하였다. 일장에 따른 생육은 엽수 및 엽초경은 장일조건에서 생육이 좋았으나 초장 및 엽초장은 장일에서 억제되는 경향을 나타내었다. 장일조건에서 육묘한 것일수록 이식 후에 구가 크고 비대도 빨랐다. 이상의 결과로 볼 때 육묘기간 중의 장일처리로서 도장의 억제 및 우량묘 생산의 가능성을 보여주고 있다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.366-376
• /
• 2008

The model tests of short pile with very small pile length/diameter(L/D) were performed in this paper. Varying the pile diameter, length, and the lateral loading point, the lateral resistance and behavior of very short pile were studied in this model tests. The experimental and analytical results are as follows. The lateral ultimate resistance of short pile in sands was the maximum at the point of h/L=0.75, regardless of pile length/diameter(L/D). As the pile diameter is larger, the lateral ultimate resistance of pile with L/D=1 decreases a little and the lateral resistance increases according to the ratio of pile length/diameter. As the lateral loads are acting on the pile, the displacement of pile head is maximum at the pile top of h/L=0, but minimum at the middle point of the pile. And if the loading point is under the middle of pile, the displacement of pile head occurs oposite in the loading direction, but its magnitude is very small.

• 한국산림과학회지
• /
• 제97권5호
• /
• pp.485-491
• /
• 2008

This study was performed in 14 unthinned Mongolian pine (Pinus sylvestris L. var. mongolica Litvin) plantations in northeast China. Data were collected on 70 sample trees of different canopy position with diameter at breast height (DBH) ranging from 6.9 cm to 34.5 cm. Diameter and length of knots per whorl below the living crown were studied by different vertical levels divided by relative knot height (RHK) in this paper. Models taking DBH and height to the crown base (HCB) as independent variables were developed to predict knot diameter (KD) in a sample whorl. According to the vertical distribution tendency and range of sound knot length (KLsound), KLsound was modeled as multiple linear function of DBH, KD and relative knot height (RHK). The loose knot length (KLloose) was described as a function of DBH, KD and height above the ground for knots (HK) in a mixed log-linear model. Results from this study can provide abundant knot information so as to describe the knot size and vertical distribution tendency of Mongolian pine plantation.