• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.844-847
• /
• 2012

By using LHTL(Left-Handed Transmission Line) which is a form of a metamaterial and conventional RHTL (Right-Handed Transmission Line), we designed, fabricated and tested a broadband $90^{\circ}$ coupler which is a basic circuit for I-Q vector signal generation. Synthetic LHTL and RHTL were implemented with capacitors and inductors only, that the size is minimized. Also, by implementing a Wilkinson power divider which is required for the suggested circuit using a synthetic RHTL, the size of whole circuit is only $11mm{\times}12mm$. For the frequency range 0.8~1.25 GHz, the phase difference at the outputs maintained $90^{\circ}{\pm}5^{\circ}$ and thus, a broadband $90^{\circ}$ coupler could be made in a compact form. for the same frequency range, the insertion loss is less than 1.6 dB and return loss is more than 10.1 dB. To the best of our knowledge, this is the smallest and broadband $90^{\circ}$ coupler for the frequency range and if the circuit is made with MMIC(Monolithic Microwave Integrated Circuit) technology, the size will be reduced much further.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.583-590
• /
• 2010

In this paper, a novel CRLH-TL unit cell with controllable transmission zeros was proposed. Proposed composite right/left handed transmission line(CRLH-TL) unit cell is implemented in the form of the metal-insulator-metal(MIM) capacitors, the microstrip stub inductors, and the co-planar waveguide(CPW) inductor. And this proposed CRLH-TL generates two transmission zeros in lower/upper passband by the effort of electromagnetic couplings between each MIM capacitors and microstrip stub inductors. Using this proposed CRLH-TL, broad bandpass filter for UWB system was designed and fabricated. The measured results reveal that the two transmission zeros are observed in lower/upper passband and the overall size of the filter, excluding the feed line is about 8 mm$\times$8 mm, less then $\lambda_g$/4 on electric size.

• Journal of Korean Neurosurgical Society
• /
• v.61 no.5
• /
• pp.568-573
• /
• 2018

Objective : Thoracic pedicles have special and specific properties. In particular, upper thoracic pedicles are positioned in craniocaudal plane. Therefore, manipulation of thoracic pedicle screws on the left side is difficult for right-handed surgeons. We recommend a new position to insert thoracic pedicle screw that will be much comfortable for spine surgeons. Methods : We retrospectively reviewed 33 patients who underwent upper thoracic pedicle screw instrumentation. In 15 patients, a total of 110 thoracic pedicle screws were inserted to the upper thoracic spine (T1-6) with classical position (anesthesiologist and monitor were placed near to patient's head. Surgeons were standing classically near to patient's body while patients were lying in prone position). In 18 patients, a total of 88 thoracic pedicle screws were inserted to the upper thoracic spine with the new standing position-surgeons stand by the head of the patient and the anesthesia monitor laterally and under patient's belt level. All the operations performed by the same senior spine surgeons with the help of C-arm. Postoperative computed tomography scans were obtained to assess the screw placement. The screw malposition and pedicle wall violations were divided and evaluated separately. Cortical penetration were measured and graded at either : 1-2 mm penetration, 2-4 mm penetration and >4 mm penetration. Results : Total 198 screws were inserted with two different standing positions. Of 198 screws 110 were in the classical positioning group and 88 were in the new positioning group. Incorrect screw placement was found in 33 screws (16.6%). The difference between total screw malposition by both standing positions were found to be statistically significant (p=0.011). The difference between total pedicle wall violations by both standing positions were found to be statistically significant (p=0.003). Conclusion : Right-handedness is a problem during the upper thoracic pedicle screw placement on the left side. Changing the surgeon's position standing near to patient's head could provide a much comfortable position to orient the craniocaudal plane of the thoracic pedicles.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.1
• /
• pp.92-96
• /
• 2011

In this paper, we present a bandpass filter (BPF) based on composite right-/left-handed (CRLH) structure for improving the linearity of the power amplifier. The proposed BPF consist of the inter-digit signal line on the top plane and the complementary split ring resonator (CSRR) on the bottom plane, respectively. The insertion loss is minimized at operation frequency and the 2nd harmonic is suppressed by the bandpass filter using the CRLH structure, respectively. The output power of 33 dBm, the 2nd harmonic of -53.527 dBc, 3rd inter-modulation distortion of -36.16 dBc was obtained at 2.14 GHz, respectively. Compared with the reference power amplifier, the 2nd harmonic of 16 dB and 3rd inter-modulation distortion of 12 dB have been improved at 2.14 GHz, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.223-230
• /
• 2008

A CRLH-TL based compact metamaterial antenna on a magneto-dielectric material is proposed. The proposed antenna is composed of two patches and vias, which is loaded by a magneto-dielectric material constructed by SRRs. The characteristic of SRRs is studied, and the size reduction of the antenna by using the magneto-dielectric material is confirmed. The simulated resonant frequency of the antenna has showed a decrease of 7.13 % at - 1st-order resonant mode, and 23.9 % at zeroth-order resonant mode. A zeroth-order resonant antenna is fabricated and measured, which has a resonant frequency of 1.888 GHz, a bandwidth of 0.48 %, a gain of 0.534 dBi, and an efficiency of 51.7 %.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.9
• /
• pp.54-58
• /
• 2011

In this paper a dual-band Class-E power amplifier using Composite Right-/Left-Handed transmission lines and PIN diode is proposed. Dual-band operation is achieved by the frequency offset and nonlinear phase slope of CRLH TL for the matching network of power amplifiers. The proposed power amplifier has been realized by using in the input and the output matching network for high power added efficiency. PIN diode has been used to obtain the dual-band of power amplifier. The measured results show that output powers of 42.17 dBm and 41.43 dBm were obtained at 800 MHz and 1900 MHz, respectively. At this frequency, we have obtained the power-added efficiency(PAE) of 67.84 % and 65.31 % in two operation frequencies, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.1
• /
• pp.68-72
• /
• 2012

In this paper, highly linear power amplifier using bandpass filter based on metamaterial and Composite Right- / Left-Handed (CRLH) structure is proposed. The proposed bandpass filter consist of the series capacitor, series microstrip line and the parallel inductor, parallel microstrip line. The insertion loss is minimized at operation frequency and the $2^{nd}$ harmonic is suppressed by the bandpass filter using the CRLH structure. And we improved the Adjacent Channel Leakage Ratio (ACLR) using the characteristic of the proposed bandpass filter. At 2.14 GHz, we have obtained the output power of 38.83 dBm, the $2^{nd}$ harmonic of .61.33 dBc, the $3^{rd}$ IMD of .54.67 dBc, and ACLR of .51.33 dBc at 5 MHz offset, -56.50 dBc at 10 MHz offset, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.12-20
• /
• 2013

In this paper, a co-planar waveguide(CPW) fed zeroth-order resonant(ZOR) antenna with frequency reconfigurable radiating structures is fabricated and measured. The unit cell of proposed antenna consists of a series metal-insulator-metal(MIM) capacitor and two shunt line inductors which are shorted through the via. The proposed antenna is designed based on a composite right/left-handed(CRLH) transmission line with two unit cells and it has open ended structure in order to radiate electromagnetic energy mainly on the shunt arm. In order to reduce the antenna size and to exhibit a frequency reconfigurable ability using diode switches four straight strips bent by 90 degrees are used as shunt inductors. The total size of fabricated antenna is $0.22{\lambda}_0{\times}0.16{\lambda}_0$ at zeroth-order resonant(ZOR) frequency. The measured maximum gain and bandwidth (VSWR ${\leq}2$) are 3.1 dBi and 56MHz at ZOR frequency of 2.97 GHz, respectively. This type of antenna can be applied to a frequency reconfigurable antenna system with triple bands.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.7 s.361
• /
• pp.1-6
• /
• 2007

In this paper, the spiral zeroth-order resonance (ZOR) antenna using composite right- and left-handed (CRLH) transmission line is proposed. The zeroth-order resonant characteristics of the antenna are described by dispersion relation of a periodic structure. The size of the $2{\times}2$ spiral ZOR antenna is $0.155{\lambda}_{0}{\times}0.155{\lambda}_{0}$. By increasing shunt inductance of CRLH transmission line, the size of this antenna is reduced by 65% compared with that of a mushroom ZOR antenna. The radiation pattern of this antenna have omnidirectional pattern which is similar to that of mushroom ZOR antenna.

• Journal of Drive and Control
• /
• v.15 no.3
• /
• pp.29-35
• /
• 2018

This paper presents the design of attachments for dual arms of disaster responding heavy machine. The heavy machine handles a variety of tasks such as cutting, shredding, picking and moving in unstructured environment. Despite the need for rapid response, the heavy machine has difficulty in repeatedly replacing the attachment depending on the task. Thus, we propose a method to solve this physical and functional contradiction relation by using TRIZ separation principles. Above all, the existing equipment and the required working scenarios were surveyed and summarized in order to separate the attachments functionally for right-handed, left-handed and two-handed operation. Then, we proposed the design directions and conceptual design as following: multi function type attachment A, for precise operation and various operations; grab type attachment B, for grasping irregular objects and auxiliary device for both arms to handle bulky objects.