• Journal of the Korea Institute of Building Construction
• /
• v.18 no.4
• /
• pp.337-345
• /
• 2018

In this study, observations of oil leakage samples taken from the actual site were performed to identify the causes of the oil leakage phenomenon. As a result, the separation of the material components was determined as the main cause of the oil leakage phenomenon based on the changes in the surface conditions, and verification of this was conducted. The evaluation results confirmed that the filler component of the asphalt mastic subsided with the lapse of the settling time, and that the difference ratio of the filler contents of the upper and lower specimens was up to 23.8% after day 28. Based on these results, a hypothesis on the oil leakage mechanism of asphalt mastic was established, and then modeling of the entire process of oil leakage was performed.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.05a
• /
• pp.440-445
• /
• 2007

This paper deals with assessment of risk component for electrical safety and investigation on the spot of computer room in elementary middle high school. The investigation was carried out side by side for floor, outlet, panel board, earth leakage circuit breaker at computer room In order to assess electrical safety at computer room, grounding simulator and power quality monitor have been used. Potential rise has been measured and analyzed for ground rod and grounding grid by using the simulator. Phase and neutral-line current have been monitored in real time. As a consequence, it is desirable for us to install conductive tile at floor of computer room Grounding grid had better than ground rod for electrical safety. Neutral-line current was produced by unbalanced phase current.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.917-922
• /
• 2008

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. Based on the nominal model derived from mathematical model, the feedback type two-degree-of-freedom controller is designed and implemented. From simulation results, the disturbances including nonlinear friction torque, leakage flow and load force can be compensated and good positioning accuracy is obtained. It show that the proposed controller is effective.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.5
• /
• pp.1013-1022
• /
• 2014

Correlation Power Analysis (CPA) is a type of Side-Channel Analysis (SCA) that extracts the secret key using the correlation coefficient both side-channel information leakage by cryptography device and intermediate value of algorithms. Attack performance of the CPA is affected by noise and temporal synchronization of power consumption leaked. In the recent years, various researches about the signal processing have been presented to improve the performance of power analysis. Among these signal processing techniques, compression techniques of the signal based on Principal Component Analysis (PCA) has been presented. Selection of the principal components is an important issue in signal compression based on PCA. Because selection of the principal component will affect the performance of the analysis. In this paper, we present a method of selecting the principal component by using the correlation of the principal components and the power consumption is high and a CPA technique based on the principal component that utilizes the feature that the principal component has different. Also, we prove the performance of our method by carrying out the experiment.

• The Journal of Engineering Geology
• /
• v.16 no.4 s.50
• /
• pp.393-402
• /
• 2006

The contamination characteristics of BTEX and TPH components in silty soils with the oil leakage event from point source were studied. The over ratios of three soil pollution standard for TPH component were $1.5{\sim}1.7$ times higher than that of BTEX component. The mean and maximum values of BTEX and TPH components with sample points were B-zone > A-zone > C-zone, and the highest concentrations were measured at $1{\sim}2m$ depth below surface. BTEX and TPH components were increased with linear distance in zone within 120 m and 80 m from point source. For the zone more than 120 m, BTEX and TPH concentrations were under soil pollution standard. The cutoff values of indicator kriging using BTEX and TPH components were defined as confirmative limit, warn- ing limit and counterplan limit. The variograms of indicator-transformed data were selected linear model. The contamination ranges of BTEX and TPH components using confirmative limit and warning limit were estimated similar, but the contamination range of those using counterplan limit was much reduced. The maximum contamination probabilities were estimated by probability maps usinB confirmative limit, warning limit and counterplan limit. The maximum contamination probabilities with three soil pollution standard were estimated 26%, 26% and 13% for BTEX component, and 44%, 38% and 26% for TPH component.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2003

In this paper, a sub-harmonic dual-gate FET mixer is suggested to improve the isolation characteristic between LO and RF ports of an unbalanced mixer. The mixer was designed by using single-gate FET cascode structure and driven by the second harmonic component of LO signal. A dual-gate FET mixer has good isolation characteristic since RF and LO signals are injected into gatel and gate2, respectively. In addition, the isolation characteristic of a sub-harmonic mixer is better than that of a fundamental mixer due to the large frequency separation between the LO and RF frequencies. As RF power was -30 ㏈m and LO power was 0 ㏈m, the designed mixer yielded the -47.17 ㏈m LO-to-RF leakage power level, 10 ㏈ conversion gain, -2.5 ㏈m OIP3, -12.5 ㏈m IIP3 and -1 ㏈m 1 ㏈ gain compression point. Since the LO-to-RF leakage power level of the designed mixer is as good as that of a double-balanced mixer, the sub-harmonic dual-gate FET mixer can be utilized instead.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.12 s.243
• /
• pp.1645-1652
• /
• 2005

Pick-and-place systems using suction cups have been being widely used and continuously developed in production automation. There are, however, some drawbacks in constructing such systems. One of them is that it generates high level noise due to air compressors. And the system must have complex constitutions of mechanical component such as air compressors, air tubes, air valves, etc. Moreover, it needs continuous air supply to maintain vacuum in suction cups. If there is a failure in any suction cup, the total suction system may fail owing to air leakage. To overcome these drawbacks, we propose PMS (Permanent Magnet Suction) mechanism which has permanent magnets for vacuuming suction cups with no air compressor. The basic concept of PMS mechanism is to rotate permanent magnets with fixed angle. Simple rotation of permanent magnets changes the direction of the magnetic force applied at the suction cups. Since each suction cup has no direct connection with any of the others, the air leakage at one suction cup is not critical. The proposed suction mechanism was designed and fabricated. With some experiments, the feasibility and performance of the PMS mechanism was shown. The strong points of the PMS mechanism are in its simple structure, generating low noise, high energy efficiency, and no need of continuous energy supply.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2004.11a
• /
• pp.29-32
• /
• 2004

In this study, we had modelled Siemens type MLC using BEAM Monte Carlo code and tested the feasibility of the modelling. To model the Primus linac MLC, we had measured the actual dimensions of MLC and each leaves, then approximated the leaf shape. VARMLC component module was used for the modelling and leakage, tongue-and-groove effect were also considered. Simulation result showed the good agreement with the film measurement.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.4
• /
• pp.279-285
• /
• 2019

This study proposes an enhanced switching pattern that can improve energy transfer efficiency in an active cell-balancing circuit using a multiwinding transformer. This balancing circuit performs cell balancing by transferring energy stored in a specific cell with high energy to another cell containing low energy through a multiwinding transformer. The circuit operates in flyback and buck-boost modes in accordance with the energy transfer path. In the conventional flyback mode, the leakage inductance of the transformer and the stray inductance component of winding can transfer energy to an undesired path during the balancing operation. This case results in cell imbalance during the cell-balancing process, which reduces the energy transfer efficiency. An enhanced switching pattern that can effectively perform cell balancing by minimizing the amount of energy transferred to the nontarget cells due to the leakage inductance components in the flyback mode is proposed. Energy transfer efficiency and balancing speed can be significantly improved using the proposed switching pattern compared with that using the conventional switching pattern. The performance improvements are verified by experiments using a 1 W prototype cell-balancing circuit.

• Journal of the Korean Society of Safety
• /
• v.37 no.6
• /
• pp.1-8
• /
• 2022

This study analyzed the characteristics of insulation resistance and operating time based on an accelerated degradation test of a low-voltage circuit breaker. The experimental sample used a molded case circuit breaker (MCCB) and an earth leakage circuit breaker (ELCB). After measuring the insulation resistance of the circuit breakers, the leakage current was affected by an external rather than an internal structure. Furthermore, the insulation resistance of the circuit breakers with accelerated degradation was measured using a Megger insulation tester. In the accelerated degradation test, aging times of five, ten, 15, and 20 years were applied according to a temperature derived using the Arrhenius equation. Circuit breakers with an equivalent life of ten, 15, and 20 years had increased insulation resistance compared to those with less degradation time. In particular, the circuit breaker with an equivalent life of ten years had the highest insulation resistance. Component analysis of the circuit breaker manufactured through an accelerated degradation test confirmed that the timing of the increase in insulation resistance and the time of additive loss were the same. Finally, after analyzing the operating time of the circuit breakers with degradation, it was confirmed that the MCCB did not change, but the ELCB breaker failed.