• 한국공간정보시스템학회:학술대회논문집
• /
• 한국공간정보시스템학회 2004년도 춘계 학술발표회 논문집 제1권1호(통권1호)
• /
• pp.83-88
• /
• 2004

First author proposed a proportioning method for member sections of a single layer reticulated dome subjected to uniform and non-uniform load without any geometrical initial imperfection, and discussed the validity and effectiveness of the method which was based on linear buckling stress and a knock down factor. However, buckling of a single layer reticulated dome is strongly affected by initial imperfection. It is well known that geometrical initial imperfections reduce the nonlinear buckling capacity of a single layer raticulated dome. Thus, structural engineers may be recommended to reflect the effects of geometrical initial imperfections in proportioning member sections. In this paper, firstly, the presented proportioning method by first author is applied to dome without consideration of any imperfections and the thickness and diameter of each member are determined. Secondly, the load bearing capacities of the proportioned domes are checked with the imperfection, by the inelastic buckling analysis.

• 설비공학논문집
• /
• 제15권1호
• /
• pp.9-18
• /
• 2003

An experimental study was performed to investigate the turbulence intermittency measuring methods across the boundary layer in the transition region. A single type hot-wire probe was used to measure instantaneous streamwise velocities in laminar, transitional and turbulent boundary layer To estimate wall shear stresses on the flat plate, near wall mean velocities are applied to the principle of CPM. Distribution of intermittency factor is obtained by dual-slope method and compared to the results of four methods,$\'{u},\;\{U}$, TERA and M-TERA method. In these methods, M-TERA shows a good agreement in the near wall region. However, the result of M-TERA method shows that intermittency factor is underestimated in the outer part and outside of the boundary layer and the dimensional constant of M-TERA method should be changed appropriately depending on measuring point.

• Computers and Concrete
• /
• 제20권3호
• /
• pp.361-368
• /
• 2017

Seismic response of the concrete column covered by nanofiber reinforced polymer (NFRP) layer is investigated. The concrete column is studied in this paper. The column is modeled using sinusoidal shear deformation beam theory (SSDT). Mori-Tanaka model is used for obtaining the effective material properties of the NFRP layer considering agglomeration effects. Using the nonlinear strain-displacement relations, stress-strain relations and Hamilton's principle, the motion equations are derived. Harmonic differential quadrature method (HDQM) along with Newmark method is utilized to obtain the dynamic response of the structure. The effects of different parameters such as NFRP layer, geometrical parameters of column, volume fraction and agglomeration of nanofibers and boundary conditions on the dynamic response of the structure are shown. The results indicated that applied NFRP layer decreases the maximum dynamic displacement of the structure. In addition, using nanofibersas reinforcement leads a reduction in the maximum dynamic displacement of the structure.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.240-250
• /
• 1995

A CPM (computational preston tube method) was developed to measure wall shear stress in a transitional boundary layer on a flat plate using Preston tubes. Correlation for the displacement factor of Preston tubes was improved for a CPM to be used in the transitional boundary layer. The distribution of skin-friction coefficient was reasonably predicted in the uniform free stream of 3.1% turbulence intensity. Reasonable and accurate estimation of displacement factor of Preston tubes was found to be of crucial importance for the CPM, especially in the laminar boundary layer. The mean velocity profiles of the boundary layer on the plate were also measured and presented.

• 한국전기전자재료학회논문지
• /
• 제17권7호
• /
• pp.793-796
• /
• 2004

In order to improve c-axis crystalline orientation and high perpendicular coercivity of deposited ${Co}_77{Cr}_20{Ta}_3$perpendicualr recording layer, Two step method was investigated using a Facing Targets Sputtering System(FTS). The ${\Delta\theta}_50$ of ${Co}_77{Cr}_20{Ta}_3$recording layer deposited on seedlayer prepared at Room Temperature was as low as $5^\circ$, while that of the recording layer without seedlayer was about 11$^{\circ}$. The Two-Step method using ${Co}_77{Cr}_20{Ta}_3$seedlayer prepared at Room Temperature was shown to be very effective in controling the c-axis orientation of ${Co}_77{Cr}_20{Ta}_3$ recording layer with thin thickness.

• 한국컴퓨터정보학회논문지
• /
• 제24권3호
• /
• pp.19-27
• /
• 2019

This paper proposes a new method using multi-layer overlapped windows to improve the performance of YOLO network which is vulnerable to detect small dense objects. In particular, the proposed method uses the YOLO Network based on the multi-layer overlapped windows to track small dense vehicles that approach from long distances. The method improves the detection performance for location and size of small vehicles. It allows crossing area of two multi-layer overlapped windows to track moving vehicles from a long distance to a short distance. And the YOLO network is optimized so that GPU computation time due to multi-layer overlapped windows should be reduced. The superiority of the proposed algorithm has been proved through various experiments using captured images from road surveillance cameras.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2008년도 공동학술대회
• /
• pp.57-62
• /
• 2008

탄성파 수치 모형 계산에 있어서 널리 사용되는 엇갈린 격자 방법이 아니라 회전된 엇갈린 격자 방법을 사용하여 탄성파 수치 모사를 수행하였다. 표준 엇갈린 격자 방법에서는 자유 경계조건을 적용하여야 하는 단점이 있지만 회전된 격자 방법에서는 자유 경계조건을 적용할 필요 없이 물성을 부여함으로써 해결될 수 있다. 파동전파에 있어서 유한 경계 조건에서 발생하는 인공 반사파를 제거하기 위하여 최근에 뛰어난 성능을 보이는 PML(Perfectly Matched Layer)법이 많이 적용되고 있다. 이 연구에서는 PML보다 성능이 뛰어나기도 하지만 차분에 있어 파동식을 분리할 필요가 없는 CPML(Convolutional Perfectly Matched Layer)법을 회전된 엇갈린 격자법(RSG : Rotatged Staggered Grid)에 적용하고자 하였다. Cerjan법의 감쇠법과 비교한 결과 매우 효과적으로 인공 반사파를 제거할 수 있음을 알 수 있었다.

• 방송공학회논문지
• /
• 제24권6호
• /
• pp.1072-1075
• /
• 2019

본 레터는 ATSC3.0 Layered-Division-Multiplexing Multiple-Inputs-Multiple-Outputs 방송 시스템에서 Core-Layer (CL) 전송 신호에 대한 새로운 연판정 복조 기법을 제안하고자 한다. 제안된 기법은 기존의 Guassian-Approximation (GA) 기법과 달리 동시에 전송되는 Enhanced-Layer 신호를 QPSK 신호로 모델링하여 CL 전송 신호를 복호하게 되며, 실험 결과 CL injection-level이 작을수록 기존의 GA 기법에 비하여 월등한 성능 향상을 보인다.

• Journal of the Korean Wood Science and Technology
• /
• 제51권4호
• /
• pp.239-252
• /
• 2023

In this study, bending and compression strength tests were performed to investigate effect of composition of layer layout of Larix cross-laminated timber (CLT) on mechanical properties. The Larix CLT consists of five laminae, and specimens were classified into four types according to grade and composition of layer. The layer's layout were composited as follows 1) cross-laminating layers in major and minor direction (Type A), and 2) cross-laminating external layer in major direction and internal layer applied grade of layer in minor direction (Type B). E12 and E16 were used as grades of lamina for major direction layer of Type A and external layer of Type B according to KS F 3020. In results of the bending test of CLT using same grade layer according to layer composition, the modulus of elasticity (MOE) of Type B was higher than Type A. In case of prediction of bending MOE of Larix CLT, the experimental MOE was higher than 1.00 to 1.09 times for Shear analogy method and 1.14 to 1.25 times for Gamma method. Therefore, it is recommended to predict the bending MOE for Larix CLT by shear analogy method. Compression strength of CLT in accordance with layer composition was measured to be 2% and 9% higher for Type A using E12 and E16 layers than Type B, respectively. In failure mode of Type A, progress direction of failure generated under compression load was confirmed to transfer from major layer to minor layer by rolling shear or bonding line failure due to the middle lamina in major direction.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.187-188
• /
• 2000

The conventional firing process method for the transparent dielectric layer in PDP Technology has disadvantages of low through put, high power consumption and large process area. We propose the rapid thermal scinterring (RTS) method as new process method to overcome these disadvantage characteristics. As the experimental result of this method, the optic transmittance(wavelength : 600nm) rate of transparent dielectric layer was more improved than conventional furnaces under the optimized gas supplying. Further, it was certified this method had the best conditions on the firing process of the PDP transparent dielectric layer.