• 해양환경안전학회지
• /
• 제28권2호
• /
• pp.414-421
• /
• 2022

해저 석유와 가스 탐사가 점점 더 깊은 수심으로 진행되고 있으며, 해저 파이프라인은 고압 및 고온 조건에서 작동하는 것이 일반적이다. 온도 및 압력 차이로 인하여 파이프 축 방향 힘이 축적되는 현상이 있다. 이러한 현상은 파이프라인을 구속하는 해저면 효과 때문에 파이프라인은 횡 좌굴이 발생하게 된다. 온도가 증가하는 경우 축 방향의 압축 하중이 가해지며 이 하중이 임계 수준에 도달하면 파이프가 수직방향으로 움직이게 된다. 또는 파이프라인의 구조적 완전성을 위태롭게 할 수 있는 횡 방향 좌굴이 발생하는 상황에서, 작동 중 파이프라인의 구조적 안전함을 보장하기 위해 파이프라인의 상세 구조 강도평가가 수행되어야 한다. 본 연구에서는 해저면의 마찰 효과 및 재료의 열 수축/팽창을 고려한 비선형 구조해석을 상용 유한요소해석 프로그램인 ANSYS를 활용하여 검토하였으며, 외부충격에 의한 횡 방향 좌굴 안전성을 분석하였다. 본 연구의 결과를 통하여 수치 해석적 단순화된 분석 모델을 통하여 해저면의 효과를 고려한 조건에서의 실제 파이프라인의 붕괴 조건을 예측할 수 있다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.193-197
• /
• 2002

The tribological properties and van der Waals attractive forces and the thermal stability of films are very important characteristics of highly hydrophobic fluorocarbon (FC) films for the long-term reliability of nano system. The effect of thermal annealing on films and van der Waals attractive forces and friction coefficient of films have been investigate d in this study. It was coated Al wafer which was treated O2 and Ar that ocatfluorocyclobutane ($C_4_{8}$) and Ar were supplied to the CVD chamber in the ratio of 2:3 for deposition of FC Films. Static contact angle and dynamic contact angle were used to characterize FC films. Thickness of films was measured by variable angle spectroscopy ellipsometer (VASE). Nanotribological data was got by atomic force microscopy (AFM) to measure roughness, lateral force microscopy (LFM) to measure friction force, and force vs. distance (FD) curve to evaluate adhesion force. FC films were cured in N2 and vacuum. The film showed the slight changes in its properties after 3 hr annealing. FTIR ATR studies showed the decrease of C-F peak intensity in the spectra as the annealing time increased. A significant decrease of film thickness has been observed. The friction force of Al surface was at least thirty times higher than ones with FC films. The adhesive force of bare Al was greater than 100 nN. After deposit FC films adhesive force was decreased to 40 nN. The adhesive force of films was decreased down to 10 nN after 24 hr annealing. During 24 hr annealing in $N_2$and vacuum at $100^{\circ}C$ film properties were not changed so much.

• Structural Engineering and Mechanics
• /
• 제70권1호
• /
• pp.13-31
• /
• 2019

A nonlinear finite element model (FEM) using ATENA-3D software to simulate the axially compressive behavior of circular steel tube confined concrete (CSTCC) columns infilled with ultra high performance concrete (UHPC) was presented in this paper. Some modifications to the material type "CC3DNonlinCementitious2User" of UHPC without and with the incorporation of steel fibers (UHPFRC) in compression and tension were adopted in FEM. The predictions of utimate strength and axial load versus axial strain curves obtained from FEM were in a good agreement with the test results of eighteen tested columns. Based on the results of FEM, the load distribution on the steel tube and the concrete core was derived for each modeled column. Furthermore, the effect of bonding between the steel tube and the concrete core was clarified by the change of friction coefficient in the material type "CC3DInterface" in FEM. The numerical results revealed that the increase in the friction coefficient leads to a greater contribution from the steel tube, a decrease in the ultimate load and an increase in the magnitude of the loss of load capacity. By comparing the results of FEM with experimental results, the appropriate friction coefficient between the steel tube and the concrete core was defined as 0.3 to 0.6. In addition to the numerical evaluation, eighteen analytical models for confined concrete in the literature were used to predict the peak confined strength to assess their suitability. To cope with CSTCC stub and intermediate columns, the equations for estimating the lateral confining stress and the equations for considering the slenderness in the selected models were proposed. It was found that all selected models except for EC2 (2004) gave a very good prediction. Among them, the model of Bing et al. (2001) was the best predictor.

• 한국지반신소재학회논문집
• /
• 제15권3호
• /
• pp.27-37
• /
• 2016

국내 GCP공법은 많은 선행연구가 진행되었으나, 설계자의 경험에 의해 의존하여 설계되고 있는 실정이므로 파괴사례가 종종 보고되고 있다. 이에 따라 명확한 파괴 원인규명 및 파괴예방대책 수립이 어려운 실정이다. 따라서 본 연구에서는 GCP공법의 합리적인 설계법의 제안을 위한 기초단계로써, GCP에 사용되는 최적배합비를 대형직접전단시험을 통해 결정하고, 내부마찰각의 변화에 따른 응력분담비의 변화 및 지반의 수직/수평 침하거동을 수치해석을 통하여 분석하였다. 직접전단 실험결과 쇄석과 모래의 최적배합비는 70:30으로 평가되었다. 수치해석결과 내부마찰각이 증가할수록 응력분담비가 증가하나 일정한 값으로 수렴하고 침하량이 감소하며, 최적배합비로 시공할 경우 측방유동 및 히빙현상의 감소를 유도할 것으로 판단된다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1191-1198
• /
• 2011

The railway business was began at England in 1767. Since then, it has been changed for configuration of rail over the years and made in the form of I. The train propulsion has been developed in a engine of steam, diesel, motor, electromagnetic force and a pneumatic engine, continuously. also, the friction has been improved in a steel-wheel, rubber tire, frictionless maglev system and railless system. In consequence, the efficiency and improvement speed for train have been accomplished. In this paper, it is investigated for the structure with lightweight using the change for supporting the form of lateral pressure by centrifugal force in the substructure supporting load for railway vehicles.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2487-2492
• /
• 2011

At high rail temperature above the neutral temperature, high compressive axial stresses will occur in the rails. High thermal axial force and vehicle loads cause the track to shift in a lateral direction and the formation of track geometry imperfections (track irregularity). When the thermal stress level and track irregularity with vehicle load reach a critical value, the track loses stability. In many studies, the stability of CWR tracks is analyzed. However these studies are only considered in temperature load. The main objective of this investigation was to estimate a new, comprehensive, realistic, the stability of CWR tracks considering wheel load. The ballast resistance is changed by wheel load. When the wheel load is applied, rails and ties are moved upward or downward. In this case the friction between ties and ballasts is decreased or increased. In this study the change of the ballast resistance of each tie was applied to the nonlinear analysis of CWR tracks.

• Tribology and Lubricants
• /
• 제28권2호
• /
• pp.62-69
• /
• 2012

Atomic force microscopy (AFM) has been widely utilized as a versatile tool not only for imaging surfaces but also for understanding nano-scale interfacial phenomena. By measuring the responses of the photo detector due to bending and torsion of the cantilever, which are caused by the interactions between the probe and the sample surface, various interfacial phenomena and properties can be explored. One of the challenges faced by AFM researchers originates in the physics of measuring the small forces that act between the probe of a force sensing cantilever and the sample. To understand the interactions between the probe and the sample quantitatively, the force calibration is essential. In this work, the procedures used to calibrate AFM instrumentation for nano-scale force measurement in normal and lateral directions are reviewed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1992년도 가을 학술발표회 논문집
• /
• pp.208-213
• /
• 1992

This research is related to the experimental verification of the shear resistance of horizontal joint in precast concrete large panel structures. a total of 9 spicemens was tested to assess their shear resistance. In the tests lateral forces have been applied to the specimen to cause shear failure while keeping the axial compression consistantly. The shear resistances of the specimens have been evaluated by investigating the deformations and failure modes of the specimens. From the test results, it is observed that the shear resistance of the horizontal joints of P.C panel structures are closely connected with shear friction mechanism.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.155-160
• /
• 2001

The road simulator system can simulate the longitudinal, lateral, and vertical movement changed by road conditions and vehicle dynamic characteristics while driving. This system provides the durability evaluation of vehicle suspensions. The system consists of hydraulic actuators, link mechanism, and servo controller. The hydraulic actuators are specially manufactured using low friction seals to endure high speed movement. The link mechanism is designed in order to minimize the dynamic effect during motion and remove the interference between 3axes actuators. The servo controller is composed of sensors, sensor amplifiers - displacement transducers and load cells, and an industrial PC with DSP board which calculates the control algorithm to control hydraulic actuators. The test results are included to evaluate the performance of this simulator comparing vehicle driving test.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.371-378
• /
• 2001

The working load at pile is sometimes subjected to not only compression load but also lateral load and uplift forces. Pile foundation is essential and uplift load can be applied because of buoyancy, a typhoon, wind or seismic forces. This study was carried out to determine the uplift capacity of concrete pile foundation driven in clay. Pile was driven in clay, between pile and clay adhesion factor was estimated, and it is the mean value between the cast-in-situ-pile and steel pipe pile. When pile foundation is loaded for long time, creep behavior occurs. The behavior of creep is originated from the clay creep contacted with pile. The creep behavior of pile foundation embedded in clay is heavily depended on the thickness of clay around the pile shaft, pore water pressure in clay, and creep behavior of clay.