• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.207-207
• /
• 2010

Both ZnO and GaN have excellent physical properties in optoelectronic devices such as blue light emitting diode (LED), blue laser diode (LD), and ultra-violet (UV) detector. The ZnO/GaN heterostructure, which has a potential to achieve the cost efficient LED technology, has been fabricated by using radio frequency (RF) sputtering, pyrolysis, metal organic chemical vapor deposition (MOCVD), direct current (DC) arc plasmatron, and pulsed laser deposition (PLD) methods. Among them, the PLD system has a benefit to control the composition ratio of the grown film from the mixture target. A 500-nm-thick ZnO film was grown by PLD technique on c-plane GaN/sapphire substrates. The post annealing process was executed at some varied temperature between from $300^{\circ}C$ to $900^{\circ}C$. The morphology and crystal structural properties obtained by using atomic force microscope (AFM) and x-ray diffraction (XRD) showed that the crystal quality of ZnO thin films can be improved as increasing the annealing temperature. We will discuss the post-treatment effect on film quality (uniformity and reliability) of ZnO/GaN heterostructures.

• Carbon letters
• /
• 제19권
• /
• pp.72-78
• /
• 2016

Spinnable pitches and carbon fibers were successfully prepared from petroleum or coal pyrolysis residues. After pyrolysis fuel oil (PFO), slurry oil, and coal tar were simply filtered to eliminate the solid impurities, the characteristics of the raw materials were evaluated by elemental analysis, ¹³C nuclear magnetic resonance spectrometer, matrix-assisted laser desorption/ionization time-of-flight mass spectrometer (MALDI-TOF-MS), and so on. Spinnable pitches were prepared for melt-spinning carbon fiber through a simple distillation under strong nitrogen flow, and further vacuum distillation to obtain a high softening point. Carbon fibers were produced from the above pitches by single-hole melt spinning and additional heat treatment, for oxidization and carbonization. Even though spinnable pitches and carbon fibers were processed under the same conditions, the melt-spinning and properties of the carbon fiber were different depending on the raw materials. A fine carbon fiber could not be prepared from slurry oil, and the different diameter carbon fibers were produced from the PFO and coal tar pitch. These results seem to be closely correlated with the initial characteristics of the raw materials, under this simple processing condition.

• Advances in nano research
• /
• 제3권3호
• /
• pp.123-131
• /
• 2015

The unintentionally doped and bismuth (Bi) doped zinc oxide (ZnO) films were prepared by spray pyrolysis at $450^{\circ}C$ with zinc acetate and bismuth nitrate precursor. The n-type conduction with concentration $6.13{\times}10^{16}cm^{-3}$ can be observed for the unintentionally doped ZnO. With the increasing of bismuth nitrate concentration in precursor, the p-type conduction can be observed. The p-type concentration $4.44{\times}10^{17}cm^{-3}$ can be achieved for the film with the Bi/Zn atomic ratio 5% in the precursor. The photoluminescence spectroscopy with HeCd laser light source was studied for films with different Bi doping. The photocatalytic activity for the unintentionally doped and Bi-doped ZnO films was studied through the photodegradation of Congo red under UV light illumination. The effects of different Bi contents on photocatalytic activity are studied and discussed. Results show that appropriate Bi doping in ZnO can increase photocatalytic activity.

• 한국입자에어로졸학회지
• /
• 제12권3호
• /
• pp.65-72
• /
• 2016

Nanoporous $SiO_2$ particles containing different pore volume and size were prepared from silicic acid by a spray pyrolysis. The pore size, pore volume and particle size could be controlled with varying the precursor concentration, reaction temperature, and amount of organic templates such as Urea and poly ethylene glycol (PEG). The pore size distribution, pore volume and specific surface area of as-prepared particles were analyzed by BET and BJH methods, and the average particle sizes were measured by a laser diffraction method. The nanoporous $SiO_2$ particles ranged $0.6-0.9{\mu}m$ in diameter were successfully synthesized and the average particle size increased as the silicic acid concentration increased. The morphology of nanoporous $SiO_2$ particles was spherical and pores ranged 1 - 40 nm in diameter were measured in the particles. In case of Urea added into silicic acid, it showed no much difference in the morphology, pore size and pore volume at different Urea concentration. On the other hand, when PEG was added, it was clearly observed that pore diameter and pore volume of the particles surface increased with respect to PEG concentration.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.171-177
• /
• 2005

In order to investigate the effect of dimethyl ether (DME) on PAH and soot formation, the fuel has been mixed to the counter-flow diffusion flames of ethylene. Laser-induced incandescence and laser-induced fluorescence techniques were employed to measure relative concentrations of soot volume fraction and polycyclic aromatic hydrocarbon (PAH) concentration, respectively. Results showed that even though pure DME flame produces the minimal amount of PAH and soot, the mixture fuel of DME and ethylene could increase PAH and soot formation, as compared to those of pure ethylene flame. This implies that even though DME has been known to be a clean fuel for soot formation, the mixture fuel of DME and the hydrocarbon fuel could produce enhanced production of soot. Numerical simulation demonstrated that methyl (CH$_{3}$) radical generated by the initial pyrolysis of DME can be contributed to the enhancement of PAH and soot formation, through the formation of propargyl (C$_{3}$H$_{3}$) radical.

• 한국자기학회지
• /
• 제3권2호
• /
• pp.143-148
• /
• 1993

열 분해법으로 $Bi_{x}Dy_{3-x}Al_{1}Fe_{4}O_{12}$(x=1, 1.2, 1.5) 자기 가넷 박막을 유리기판 위에 제조하였다. Bi 치환량을 증가시켰을 때 $M_{s}$ 값은 5 emu/cc에서 12 emu/cc로 증가하였고, 제조된 모든 박막이 수직 자기 이방성을 나타내었다. Bi 양의 증가에 따라 파장 780 nm의 광원을 사용했을 때 패러디 회전각이 $0.11^{\circ}/\mu\textrm{m}$에서 $0.20^{\circ}/\mu\textrm{m}$로 증가 하였으며 가넷 결정화 온도는 $660^{\circ}C$에서 $630^{\circ}C$로 감소하였다. 또한 보자력은 1200 Oe에서 600 Oe로 감소하였으며 결정립의 크기가 증가하였다. 박막의 두께를 $2000\;{\AA}$에서 $4000\;{\AA}$으로 증가시킴에 따라 $H_{c}$가 1750 Oe에서 1200 Oe로 감소했으며 ${\theta}_F$는 반사광의 간섭 효과에 의해 증가하였다.

• 공업화학
• /
• 제34권4호
• /
• pp.383-387
• /
• 2023

범용적으로 고진공 성막 장비에서 사용되는 quartz crystal microbalance (QCM)는 두꺼운 필름이 quartz 위에 성막되는 경우, 크리스탈 고유의 진동에 영향을 주어 사용이 어려워진다. 본 논문에서는 실시간 필름 증착 공정 중에 센서의 손상이 없는 광학적 계측 방식을 통해 필름의 성막 속도를 측정하는 방법을 연구하였다. 기체 이동 경로로 지나가는 페럴린 가스 중 다이머에 의한 레이저의 산란 정도를 측정하여, 페럴린 공정의 분해부 온도가 감소할수록 페럴린 가스 중 다이머의 비율이 증가하는 것을 성공적으로 확인하였다. 또한, 성막된 필름의 특성을 확인한 결과, 분해부 온도가 감소할수록 필름의 두께와 haze가 증가한 것을 확인할 수 있었다. 우리는 연구 결과를 통해 개발한 안정적인 실시간 성막 속도 계측 시스템을 이용함으로써, 진공 공정을 통해 성막하는 페럴린 필름의 정밀한 성막 속도 제어에 활용하고자 한다.

• 공업화학
• /
• 제33권5호
• /
• pp.496-501
• /
• 2022

본 연구에서는 석유 정제 부산물인 석유계 잔사유를 이용하여 리튬이차전지용 음극재를 제조하였다. 석유계 잔사유 중 열분해 연료유(pyrolysis fuel oil, PFO), 유동접촉분해 데칸트 오일(fluidized catalyst cracking-decant oil, FCC-DO), 감압잔사유(vacuum residue, VR)를 탄소 전구체로 사용하였다. MALDI-TOF, 원소분석(EA)을 통하여 석유계 잔사유의 물리화학적 특징을 확인하였고, 잔사유로부터 제조된 음극재는 XRD, Raman 등의 분석을 통해 그 구조적 특징을 평가하였다. VR은 PFO 및 FCC-DO에 비하여 광범위한 분자량 분포와 많은 양의 불순물을 함유하는 것을 확인할 수 있었고, PFO와 FCC-DO는 거의 유사한 물리화학적 특징을 나타내었다. XRD 분석결과로부터 탄화된 PFO와 FCC-DO는 유사한 d₀₀₂값을 나타내었다. 그러나 Lc 및 La값에서는 FCC-DO가 PFO보다 더 발달된 층상구조를 갖는 것으로 확인되었다. 또한, 전기화학적 특성 평가에서는 FCC-DO가 가장 우수한 사이클 특성을 나타내었다. 이러한 석유계 잔사유의 물리화학적, 전기화학적 결과로 미루어 보아 FCC-DO가 PFO와 VR보다 더 우수한 리튬이차전지용 탄소 전구체인 것으로 사료된다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 하계종합학술대회 논문집
• /
• pp.275-278
• /
• 1999

We have grown vertically aligned carbon nanotubes in a large area of Co-Ni codeposited Si substrates by the thermal CVD using $C_2$H$_2$gas. Since the discovery of carbon nanotubes, Synthesis of carbon nanotubes for mass production has been achieved by several methods such as laser vaporization, arc discharge, and pyrolysis. In particular, growth of vertically aligned nanotubes is of technological importance for applications to FED. Recently, vertically aligned carbon nanotubes have been grown on glass by PECVD. Aligned carbon nanotubes can be also grown on mesoporous silica and Fe patterned porous silicon using CVD. Despite such breakthroughs in the growth, the growth mechanism of the alignment are still far from being clearly understood. Furthermore, FED has not been clearly demonstrated yet at a practical level. Here, we demonstrate that carbon nanotubes can be vertically aligned on catalyzed Si substrate when the domain density reaches a certain value. We suggest that steric hindrance between nanotubes at an initial stage of the growth forces nanotubes to align vertically and then nanotubes are further grown by the cap growth mechanism.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제25회 KOSCI SYMPOSIUM 논문집
• /
• pp.123-128
• /
• 2002

이중동축류 버너를 사용하여 에틸렌/프로판 및 에틸렌/메탄 혼합 연료의 매연생성 상승효과와 관련된 매연생성 메커니즘을 이해하기 위한 실험을 수행하였다. 매연체적분율, 광산란신호 및 PAH 형광신호를 측정한 결과 다음을 알 수 있었다. 에틸렌/프로판 혼합연료에서 연료공급 위치의 변화에 따른 매연생성특성의 변화는 대부분 synergistic 효과와 관련되는 것임을 알 수 있었다. 그러나 에틸렌/메탄 혼합연료의 경우 연료공급의 위치변화가 매연생성에 크게 영향을 주지 않았다. PAH 분포는 synergistic 효과에 의한 매연 생성 특성의 변화와 일관성이 없는 것이 관찰되었다. 따라서 synergistic 효과에 대한 PAH의 역할에 대한 이해가 필요함을 알 수 있었다.