• Analytical Science and Technology
• /
• v.34 no.1
• /
• pp.23-35
• /
• 2021

In order to measure the volatile organic compounds (VOCs) of a sample which is too large to use commercially available chamber, a stainless steel vacuum chamber (VC) (with an internal diameter of 205 mm and a height of 50 mm) was manufactured and the temperature of the chamber was controlled using an oven. After concentrating the volatiles of the sample in the chamber by helium gas, it was made possible to remove residual volatile substances present in the chamber under reduced pressure ((2 ± 1) × 10-2 mmHg). The chamber was connected to a purge & trap (P&T) using a 6 port valve to concentrate the VOCs, which were analyzed by gas chromatography-mass spectrometry (GC-MS) after thermal desorption (VC-P&T-GC-MS). Using toluene, the toluene recovery rate of this device was 85 ± 2 %, reproducibility was 5 ± 2 %, and the detection limit was 0.01 ng L-1. The method of removing VOCs remaining in the chamber with helium and the method of removing those with reduced pressure was compared using Korean drinking water regulation (KDWR) VOC Mix A (5 μL of 100 ㎍ mL-1) and butylated hydroxytoluene (BHT, 2 μL of 500 ㎍ mL-1). In case of using helium, which requires a large amount of gas and time, reduced pressure ((2 ± 1) × 10-2 mmHg) only during the GC-MS running time, could remove VOCs and BHT to less than 0.1 % of the original injection concentration. As a result of analyzing volatile substances using VC-P&T-GC-MS of six types of cell phone case, BHT was detected in four types and quantitatively analyzed. Maintaining the chamber at reduced pressure during the GC-MS analysis time eliminated memory effect and did not affect the next sample analysis. The volatile substances in a cell phone case were also analyzed by dynamic headspace (HT3) and GC-MS, and the results of the analysis were compared with those of VC-P&T-GC-MS. Considering the chamber volume and sample weight, the VC-P&T configuration was able to collect volatile substances more efficiently than the HT3. The VC-P&T-GC-MS system is believed to be useful for VOCs measurement of inhomogeneous large sample or devices used inside clean rooms.

• Korean Journal of Food Science and Technology
• /
• v.32 no.4
• /
• pp.881-888
• /
• 2000

Lactic acid bacteria(LAB) fermented food was prepared with milk or egg white powder(EWP) and added with freeze drying protectant(FDP). 0.2% of Tween 80 or 1% of ascorbate was added to milk sample and 3% of raffinose or 1% of ascorbate was added to EWP sample. Effects of FDP on sensory property, volatile aroma compounds and physical property of LAB fermented food were investigated. In case of non-freeze dried samples, sensory properties of milk sample with ascorbate were slightly better than those of reference sample(milk), while sensory properties of EWP sample or EWP sample with FDP were slightly inferior to reference sample. Sensory properties of all of the freeze dried/reconstituted samples were not different. Sensory properties of milk sample with ascorbate were reduced by freeze drying/reconstitution, while those of sample with ascorbate were not changed. Although all of the volatile aroma compounds were reduced by freeze drying, the residual ratio was slightly different between milk samples and EWP samples. Difference in volatile aroma compounds between milk samples and EWP samples before freeze drying was relatively large, while difference between two sample groups after freeze drying/reconstitution was relatively small. Rheological properties of milk samples were markedly changed by freeze drying/reconstitution, while those of EWP samples were changed slightly.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.2
• /
• pp.244-258
• /
• 2018

We performed this study to investigate the spatial, seasonal, and daily variations of the concentrations of volatile organic compounds (VOCs) in Pohang, where large steel industrial complexes are located. Ambient air sampling was undertaken at 4 sites during 4 seasons. Each sample was taken for 4 hours continuously for 8 consecutive days per season at each site. Three sites were located within the Pohang city, but one as a control site in Gyeongju. A total of 72 individual VOCs were determined by thermal desorption coupled with GC/MS, including aliphatics, aromatics, carbonyls and halides. The most abundant VOC was toluene, being followed by ethylbenzene and xylenes. Benzene concentrations(c.a. 0.7 ppb) were found to be much lower than the national ambient standard of 1.5 ppb. Overall, the VOCs levels in Pohang appeared to be lower than other national industrial complexes in Korea such as Shiwha-Banwol, Yeosu-Gwangyang, Gumi, and Ulsan. This implies that steel industry may not give significant impacts on the atmospheric levels of VOCs as much as petrochemical, electronic, and/or textile industries, where large amounts of organic solvents are used.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.37 no.1
• /
• pp.113-123
• /
• 2013

Clothes that retain and emanate body odor feel uncomfortable and unclean; subsequently, the adsorption, desorption and removal amounts of malodorous compounds from fabrics with different polarities were examined. 1-Octen-3-one, octanal and isovaleric acid, which are important malodor compounds from the body, were used as volatile organic compounds (VOC). Samples were prepared with unfinished and ${\beta}$-CD finished cotton, nylon and PET fabrics. The amounts of VOCs retained on the fabrics were measured using headspace GC-MS; in addition, the odor intensity of the samples were evaluated by 10 trained panelists. The amounts adsorbed were estimated by weight gain; however, moisture was found to have a larger effect on the increase in weight than VOCs. The polarity of the VOCs decreased in the order of isovaleric acid, octanal and 1-octen-3-one. Despite the exceptionally large amounts of octanal adsorbed on the nylon sample, the amounts of malodorous compounds adsorbed on fabrics increased with the decreasing VOC molecular weight. The unfinished PET sample adsorbed more VOCs than the unfinished-fabric samples. The odor intensity was mostly weaker in the ${\beta}$-CD finished fabrics than in the unfinished fabrics. The odor intensity of the ${\beta}$-CD finished fabrics was lower than unfinished fabrics. The amount of VOCs that remained on the soiled fabric samples after storing in air for 24 hrs decreased with the increasing VOC vapor pressure. Most VOCs were removed by washing; however, more VOCs were left on the ${\beta}$-CD finished fabrics than unfinished fabrics. The intensity of the odor from the unfinished PET and ${\beta}$-CD finished fabrics was stronger and weaker, respectively, than that of other fabrics, even when the same amounts of VOCs remained.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.9
• /
• pp.11-18
• /
• 2016

In this paper, we propose a gas classification method using combined features for an electronic nose system that performs well even when some loss occurs in measuring data samples. We first divide the entire measurement for a data sample into three local sections, which are the stabilization, exposure, and purge; local features are then extracted from each section. Based on the discrimination analysis, measurements of the discriminative information amounts are taken. Subsequently, the local features that have a large amount of discriminative information are chosen to compose the combined features together with the global features that extracted from the entire measurement section of the data sample. The experimental results show that the combined features by the proposed method gives better classification performance for a variety of volatile organic compound data than the other feature types, especially when there is data loss.

• Journal of Korean Society of Water and Wastewater
• /
• v.10 no.2
• /
• pp.104-116
• /
• 1996

Anaerobic digestion is generally used for the treatment of volatile organic solids such as manure and sludge from waste water treatment plants. However, the reaction rate of anaerobic process is slow, and thus it requires a large reactor volume. To minimize such a disadvantage, physical and chemical pre-treatment is generally considered. Another method to reduce the reactor size is to adopt different reactor system other than CSTR. In this paper, the effects of heat pre-treatment and reactor configurations on the anaerobic treatability of volatile solids was studied. Carrot, kale, primary sludge, and waste activated sludge was chosen as the test materials, and the BMP method was used to evaluate the maximum methane production and first order rate constants from each sample. After the heat treatment at $130^{\circ}C$ for 30min., the measured increase in SCOD per gram VS was up to 394 mg/L for the waste activated sludge. However, the methane production potential per gram VS was increased for only primary and waste activated sludge by 17-23%, remaining the same for carrot and kale. The overall methane production process for the tested solids can be described by first order reactions. The increased in reaction constant after heat pre-treatment was also more significant for the primary and waste activated sludge than that for carrot and kale. therefore, the heat pre-treatment appeared to be effective for the solids with high protein contents rather than for the solids with high carbohydrate contents. Among the four reactor systems studied, CSTR, PFR, CSTR followed by PFR, and PFR with recycle, CSTR followed by PFR appeared to be the best choice considering methane conversion rate and the operational stability.

• The Korean Journal of Financial Management
• /
• v.22 no.2
• /
• pp.165-187
• /
• 2005

This paper tries to investigate the relationships among stock return volatility, time-varying risk premium and Korea Discount. Using Korean Composite Stock Price Index (KOSPI) return from January 4, 1980 to August 31, 2005, this study finds possible links between time-varying risk premium and Korea Discount. First of all, this study classifies Korean stock returns during the sample period by three regime-switching volatility period that is to say, low-volatile period medium-volatile period and highly-volatile period by estimating Markov-Switching ARCH model. During the highly volatile period of Korean stock return (09/01/1997-05/31/2001), the estimated time-varying unit risk premium from the jump-diffusion GARCH model was 0.3625, where as during the low volatile period (01/04/1980-l1/30/1985), the time-varying unit risk premium was estimated 0.0284 from the jump diffusion GARCH model, which was about thirteen times less than that. This study seems to find the evidence that highly volatile Korean stock market may induce large time-varying risk premium from the investors and this may lead to Korea discount.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.254.2-254.2
• /
• 2014

The Transmission Fourier Transform Infrared spectroscopy (FTIR) of SiOx charge storage layer with the richest silicon content showed an assignment at peaks around 2000~2300 cm-1. It indicated that the existence of many silicon phases and defect sources in the matrix of the SiOx films. The total hysteresis width is the sum of the flat band voltage shift (${\Delta}VFB$) due to electron and hole charging. At the range voltage sweep of ${\pm}15V$, the ${\Delta}VFB$ values increase of 0.57 V, 1.71 V, and 13.56 V with 1/2, 2/1, and 6/1 samples, respectively. When we increase the gas ratio of SiH4/N2O, a lot of defects appeared in charge storage layer, more electrons and holes are charged and the memory window also increases. The best retention are obtained at sample with the ratio SiH4/N2O=6/1 with 82.31% (3.49V) after 103s and 70.75% after 10 years. The high charge storage in 6/1 device could arise from the large amount of silicon phases and defect sources in the storage material with SiOx material. Therefore, in the programming/erasing (P/E) process, the Si-rich SiOx charge-trapping layer with SiH4/N2O gas flow ratio=6/1 easily grasps electrons and holds them, and hence, increases the P/E speed and the memory window. This is very useful for a trapping layer, especially in the low-voltage operation of non-volatile memory devices.

• Analytical Science and Technology
• /
• v.14 no.3
• /
• pp.274-285
• /
• 2001

In this study, the thermal desorption-cryofocusing-gas chromatographic(TD-C-GC) method was developed for determination of volatile organic compounds(VOCs) in ambient air and was applied at the municipal solid waste landfill sites. On-column cryofocusing was possible only with a 100 ml dewars bottle in TD-C-GC method with a stainless steel column. However, high operating pressure was needed for purging VOCs from the absorbent trap, which was able to solve by pressure programming with a electric pressure controller. By using both pressure and temperature programming brought increasing of resolution power in on-column cryofocusing method, but the high pressure caused a leakage of sample tube with repeated use. A loop cryofocusing devise was also developed and compared with the direct on-column method. In loop cryofocusing method, VOCs were concentrated on a 0.8mm i.d. loop which is located between the injector and separation column by using liquid nitrogen. In order to purge VOCs from the absorbent trap, only 0.4 psi of pressure was need in the loop cryofocusing method. Dual detection system was applied for the analysis of VOCs; a FID was used for hydrocarbons and a FPD was used for sulfur-containing compounds. Qualitative analysis was done by on-column cryofocusing GC-MS system. Among the large number of VOCs, toluene was the most abundant. Hydrogen sulfide, dimethyl sulfide, carbon disulfide, dimethyl disulfide and methyl propyl disulfide were detected at landfill site by FPD.

• Journal of the Korean Society of Tobacco Science
• /
• v.14 no.2
• /
• pp.159-167
• /
• 1992

It would be clear that the constituents of the leaf surface lipid is ye비 important as an evaluation index of tobacco leaf quality since the quality of tobacco specific aroma with leaf species depends on the contents of the lipid and the strength of the aroma is determined by the amounts of the lipid secreted. For the reason, a rapid and peproducible method to quantify DVT, which is a kind of lipid, has been studied. The biosynthesis procedure of DVT in leaf growing processes, and the volatile or decompositional characters of DVT in leaf drying processes were also discussed. In consequence, it might be possible to get the data available to the cultivation of better tobacco leaf and the manufacture of cigarettes with better aroma and taste. The results obtained from this study are as follows. 1. Chloroform/dichloromethane solvent was better than chloroform alone for DVT extraction. The extraction yields of the leaf surface lipid were about 5% 2. The extractives with dichloromethane were treated by silylation with BSTPa and the quantitative analysis of DVT was carried out using SE -54 fused silica capillary column. It was found that rapid and reproducible data could be obtained from these methods. 3. In flue - cured tobacco species, DVT contents were $30.3\mu\textrm{g}/cm^2$ in the beginning stage of leaf drying processes and $12.1\mu\textrm{g}/cm^2$ corresponded to 30% levels of the beginning stage, in the end stage. 4. DVT contents in Burley mere 2 times as large as those in fluecured tobacco. DVT in the upper stalk position of leaf was 3 times larger than that in the lower stalk position. 5. DVT of tobacco leaves was decomposed by $SO_2$ gas or the sun light. The decomposition rate was largest in the sample used methanol as a extraction solvent.