• 한국환경과학회지
• /
• 제32권3호
• /
• pp.181-189
• /
• 2023

In this study, sediment cores from unvegetated tidal flats in the Hampyeong Bay (west coastal wetland) and Dongdae Bay (south coastal wetland) were sampled, the blue carbon stock in the sediments was calculated, and the characteristics of the blue carbon stock were analyzed based on particle size of the sediments. The sediments in the Hampyeong Bay tidal flat had large particle size and low mud content, and the Dongdae bay tidal flat had small particle size and high mud content. The organic carbon content and blue carbon stock in the sediments were higher in the Dongdae tidal flat than in the Hampyeong Bay tidal flat. As a result of the regression function, in both the Hampyeong Bay and Dongdae Bay tidal flats, the sediments had the smaller particle size and higher mud contents the higher the organic carbon content and blue carbon stock. The sediments with smaller particle size had the larger specific surface area, so were feasible to adsorb and store more organic matters.

• 한국지형학회지
• /
• 제19권4호
• /
• pp.157-168
• /
• 2012

언양단면은 울산광역시 울주군 삼남면 신화리의 삼동천이 태화강에 유입하는 지점에 위치한다. 언양단면에서 OSL 연대측정, 대자율, Y값 및 입도 분석 등 다양한 물리적 분석을 행하였다. 상부층의 조립 물질은 바람에 의해 주로 근거리에서 운반되었으며, 점이층과 하부층의 조립 물질은 유수에 의해 퇴적되었다. 언양단면은 대자율 변화의 불규칙성, Y값의 높은 편차, 매우 불량한 분급 등 한국의 봉동, 거창, 대천 등 다른 지역 퇴적층과 차이가 크다. 이러한 언양단면의 특성은 기존의 중국 뢰스고원과 인접한 범람원 등 다양한 기원지로부터 운반되었거나 다른 작용의 영향을 전체적으로 받았을 가능성을 시사한다. 언양단면의 퇴적물은 MIS 3 후기부터 MIS 2 시기까지 형성되었다.

• 한국조경학회지
• /
• 제40권6호
• /
• pp.140-147
• /
• 2012

본 연구는 입주 초기 아파트 외부조경의 효과를 높이고, 입주자들에게 조경수목 식재가 주는 효용을 부각시키면서 적정한 식재밀도로 최대 효과를 얻을 수 있는 식재밀도의 적정 기준을 마련하기 위해 수행되었다. 이를 위해 법적 조경기준의 식재밀도 적정성을 검토하고, 장기적인 생육을 고려하기 위해 조림지를 대상으로 산정한 도시림의 입목밀도를 적정 식재밀도로 가정하여 이를 현장조사 결과와 비교하였다. 현장조사는 최근 10년 이내에 준공된 수도권에 위치한 아파트 단지 3개소를 대상으로 각 단지별로 10개소씩 검토대상지를 선정하여 단위면적당 수목 밀도를 산정하였다. 이를 표준규격의 경우와 대경목 식재에 따라 가중치를 인정한 경우로 구분하여 현행 조경기준과 도시림 적정 입목밀도 기준을 비교 검토하였다. 또한 하층식생의 적절한 생육 및 적절한 그늘 제공 등을 검토하기 위해 수관투영면적 비율 산정을 병행하였다. 그 결과 현행 조경기준의 최소식재기준은 매우 합리적으로 설정된 것을 확인할 수 있었다. 그러나 대경목을 식재하여 식재밀도의 가중치를 인정받는 경우에는 조경기준의 식재밀도가 도시림의 적정 입목밀도에 비해 부족하고 수관투영면적 비율 역시 50% 미만으로 부족한 것으로 산정되어 추가 식재가 필요한 것으로 분석되었다. 아파트 단지 3개소에 대한 검토 결과 모두 법적 조경기준을 충족하거나 초과하고 있었다. 조경기준에 따라 상록교목 대경목의 가중치를 인정한 경우 경관을 고려하여 추가식재가 이루어짐에 따라 식재밀도가 과밀해지는 것으로 나타났다. 따라서 앞으로 보다 광범위한 조사를 거쳐 대경목 식재에 따른 가중치 인정 항목의 삭제 또는 인정의 최소화, 식재 당시 수관투영면적 비율을 50% 이상 100% 이하로 설정하는 등과 같은 조경기준 개정작업이 필요한 것으로 분석되었다.

• Wind and Structures
• /
• 제16권1호
• /
• pp.47-60
• /
• 2013

A dominant opening in a windward wall, which generates large internal pressures in a building, is a critical structural design criterion. The internal pressure fluctuations are a function of the dominant opening area size, internal volume size and external pressure at the opening. In addition, many buildings have background leakage, which can attenuate internal pressure fluctuations. This study examines internal pressure in buildings for a range of dominant opening areas, internal volume sizes and background porosities. The effects of background porosity are incorporated into the governing equation. The ratio of the background leakage area $A_L$ to dominant opening area $A_W$ is presented in a non-dimensional format through a parameter, ${\phi}_6-A_L/A_W$. Background porosity was found to attenuate the internal pressure fluctuations when ${\phi}_6$ is larger than 0.2. The dominant opening discharge coefficient, ${\kappa}$ was estimated to lie between 0.05 to 0.40 and the effective background porosity discharge coefficient ${\kappa}^{\prime}_L$, was estimated to be between 0.05 to 0.50.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2005년도 Proceedings of ISRS 2005
• /
• pp.698-701
• /
• 2005

This paper examines that is extracted certain information in forest areas within high resolution imagery based on wavelet transformation. First of all, study areas are selected one more species distributed spots refer to forest type map. Next, study area is cut 256 x 256 pixels size because of image processing problem in large volume data. Prior to wavelet transformation, five texture parameters (contrast, dissimilarity, entropy, homogeneity, Angular Second Moment (ASM≫ calculated by using Gray Level Co-occurrence Matrix (GLCM). Five texture images are set that shifting window size is 3x3, distance .is 1 pixel, and angle is 45 degrees used. Wavelet function is selected Daubechies 4 wavelet basis functions. Result is summarized 3 points; First, Wavelet transformation images derived from contrast, dissimilarity (texture parameters) have on effect on edge elements detection and will have probability used forest road detection. Second, Wavelet fusion images derived from texture parameters and original image can apply to forest area classification because of clustering in Homogeneous forest type structure. Third, for grading evaluation in forest fire damaged area, if data fusion of established classification method, GLCM texture extraction concept and wavelet transformation technique effectively applied forest areas (also other areas), will obtain high accuracy result.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.691-699
• /
• 2008

In the design of a foundation, settlement of the foundation may exceed allowable design criteria even with a competent bearing stratum. In such a case, a piled-raft foundation system may be adopted using piles as settlement reducing component. In this paper, Disconnected Piled Raft Foundation (DPRF) system, which installs disconnected piles underneath the raft and uses the piles as ground reinforcements, is studied as a cost effective design method against the classical piled-raft foundation system. To this end, large size loading tests were carried out on weathered ground changing area replacement ratio and length of piles. The results indicated that the settlement of the reinforced ground was reduced by 34~87% and the allowable bearing pressure increased by 70% on average from those of the unreinforced original ground, respectively. The correlating formula between the area replacement ratio and the load bearing ratio of piles were derived from the test results and numerical analysis. From the correlation, a design method determining the size and the quantity of the disconnected piles to enhance the bearing capacity of original ground to the desired value was proposed based on one inch settlement criteria.

• Imaging Science in Dentistry
• /
• 제49권2호
• /
• pp.131-137
• /
• 2019

Purpose: This study was designed to investigate the effects of voxel size, the oversampling technique, and the direction and area of measurement on modulation transfer function (MTF) values to identify the optimal method of MTF measurement. Materials and Methods: Images of the wire inserts of the SedentexCT IQ phantom were acquired, and MTF values were calculated under different conditions(voxel size of 0.1, 0.2, and 0.3 mm; 5 oversampling techniques; simulated pixel location errors; and different directions and areas of measurement). The differences in the MTF values across various conditions were evaluated. Results: The MTF 10 values showed smaller standard deviations than the MTF 50 values. Stable and accurate MTF values were obtained in the 0.1-mm voxel images. In the 0.3-mm voxel images, oversampling techniques of 11 lines or more did not show significant differences in MTF values depending on the presence of simulated location errors. MTF 10 values showed significant differences according to the direction and area of the measurement. Conclusion: To measure more accurate and stable MTF values, it is better to measure MTF 10 values in small-voxel images. In large-voxel images, the proper oversampling technique is required. MTF values from the radial and tangential directions may be different, and MTF values vary depending on the measured area.

• 한국지반신소재학회논문집
• /
• 제9권1호
• /
• pp.1-11
• /
• 2010

본 연구에서는 대상지역에 대한 지질조건에 따른 토질특성을 조사하였다. 대상지역의 지질은 인곡응회암, 유치역암, 다도응회암 등으로 구분되며, 유치역암은 대상지역의 약 80%를 점유하고 있다. 대상지역에 주로 분포하고 있는 역암, 응회암 및 세일구간에 대하여 비교란 및 교란시료를 채취하고 각종 실내토질시험을 실시하였다. 역암지역의 경우 건조단위중량이 크고 투수계수가 작으며, 응회암 및 셰일 지역의 경우 건조단위중량이 작고 투수계수가 큼을 알 수 있다. 흙의 유효입경과 세립토함유량은 흙의 투수계수에 많은 영향을 미치고 있음을 알 수 있다. 즉, 흙의 유효입경이 증가함에 따라 흙의 투수계수는 증가하고, 흙의 세립토 함유량이 증가함에 따라 투수계수는 감소하게 된다.

• 한국재료학회지
• /
• 제20권5호
• /
• pp.252-256
• /
• 2010

The study was done to change the morphology and pore size of SBA-15 silica, and the characteristics of SBA-15 silica were investigated with TG-DSC, XRD, SEM, TEM and N2 adsorption-desorption under changing aging conditions. SBA-15 silica having a 2D-hexagonal structure was synthesized and confirmed by SEM and TEM. The structure of mesoporus silica SBA-15 showed a pore having regularly formed hexagonal structure and a passage having a cylindrical shape. This result is in good agreement with the pore forming in XRD and cylindrical shape of the structure in $N_2$ adsorption-desorption isotherm. SBA-15 silica showed a large BET surface area of $603-698\;m^2/g$, a pore volume of $0.673-0.926\;cm^3/g$, a large pore diameter of 5.62-7.42 nm, and a thick pore wall of 3.31-4.37 nm. This result shows that as the aging temperature increases, the BET surface area, pore volume, and pore diameter increase but the pore wall thickness decreases. The BET surface areas in SM-2 and SM-3 are as large as $698\;m^2/g$. However, SM-2 has a large surface area and forms a thick pore wall, when the aging temperature is $100^{\circ}C$ and is synthesized into stable mesoporous SBA-15 silica.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.547-552
• /
• 2011

Drying process, corresponding to a final process in the area of food engineering, requires a lot of heat energy. Thus, the energy efficiency is very important for dryers. Since the energy efficiency of heat pump dryers is much higher compared to that of electric dryers or other types of dryers, most of large-capacity dryers are adopting heat pump. In this study, shapes, positions and number of air-circulating fans, guide vanes, air inlet, outlet and top separator were varied for optimization of the flow of a large-capacity heat pump dryer. In addition, fans were modelled with performance curves and porous media were assumed for foods and heat exchangers. The simulation results were applied to the 12-ton dryer and the velocity distributions were experimentally examined. Finally, uniform drying in time was successfully accomplished through frozen pepper experiment.