• Journal of Biosystems Engineering
• /
• 제28권6호
• /
• pp.485-490
• /
• 2003

Flexural rigidity(EI) and deflection characteristics of rice stalks were studied to investigate the mechanical interaction between a rice stalk and a combine reel in harvesting. Deflection of a rice stalk caused by reel operation is so large that conventional equation of small deflection fer elastic beam cannot be applied to the study of deflection characteristics. Therefore, an equation of large deflection for elastic beam was introduced in this study. Feasibility of this equation was examined by comparing theoretical calculation with the measured results for piano wire, and by the relationship between deflection and load acting on a rice stalk which was presumed by this equation. Results showed that the large deflection equation could predict the measurement data quite well. From this research, the following results were obtained. 1. Flexural rigidity(EI) calculated from the equation of large deflection was 4.0${\times}$l0$^4$N$.$$\textrm{mm}^2$(diameter 1.4mm, deflection 300mm) while the actual EI value of a piano wire(diameter 1.4mm) was 3.9${\times}$10$^4$N$.$$\textrm{mm}^2$. 2. The relationship between deflection and load acting on a rice stalk could be presumed by the large deflection equation. Flexural rigidity values of tested rice stalks calculated from the equation of large deflection were 1.6∼2.4${\times}$ l0$^4$N$.$$\textrm{mm}^2$(Hwa sung), 2.7∼3.5${\times}$ l0$^4$N$.$$\textrm{mm}^2$(Il pum) and 1.7∼2.4${\times}$ l0$^4$N$.$$\textrm{mm}^2$(Damakum)

• 대한조선학회지
• /
• 제25권1호
• /
• pp.33-46
• /
• 1988

This paper describes a simplified method for estimation of the ultimate compressive strength of actual ship panels with initial deflection of complex shape. The proposed method consists of the elastic analysis using the large deflection theory and the rigid-plastic analysis based on the collapse mechanism which also includes the large deformation effect. In order to reduce the computing time for the elastic large deflection theory and the rigid-plastic analysis based on the collapse mechanism which also includes the large deformation effect. In order to reduce the computing time for the elastic large deflection analysis, only one term of Fourier series for the plate deflection is considered. The results of the proposed method are in good agreement with those calculated by the elasto-plastic large deflection analysis using F.E.M. and the computing time of the proposed method is extremely short compared with that of F.E.M.

• Structural Engineering and Mechanics
• /
• 제8권2호
• /
• pp.151-164
• /
• 1999

The large deflection theory of the Mindlin plate and Galerkin's method are employed to examine the static responses of a plate produced by the weight of the plate, and the dynamic responses of the plate caused by the coupling effect of these static responses with a set of moving forces. Results obtained by the large deflection theory are compared with those by the small deflection theory. The results indicate that the effect of weight of the plate increases the modal frequencies of the structure. The deviations of dynamic transverse deflection and of dynamic bending moment produced by a moving concentrated force between the two theories are significant for a thin plate with a large area. Both dynamic transverse deflection and dynamic bending moment obtained by the Mindlin plate theory are greater than those by the classical plate.

• Structural Engineering and Mechanics
• /
• 제44권3호
• /
• pp.405-416
• /
• 2012

In this study the investigation of large deflections subject in compliant mechanisms is presented using homotopy perturbation method (HPM). The main purpose is to propose a convenient method of solution for the large deflection problem in compliant mechanisms in order to overcome the difficulty and complexity of conventional methods, as well as for the purpose of mathematical modeling and optimization. For simplicity, a cantilever beam of linear elastic material under horizontal, vertical and bending moment end point load is considered. The results show that the applied method is very accurate and capable for cantilever beams and can be used for a large category of practical problems for the aim of optimization. Also the consequence of effective parameters on the large deflection is analyzed and presented.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.97-103
• /
• 2002

Vibration isolation technology using an air spring and laminated rubber bearing is widely used because it has excellent vibration isolation characteristics. In the part of that, we usually make use of the self-damped air suing. It is occupied two chambers, restrictor, diaphragm and load plate. Two chambers contain compressed air and the volume of chambers and the area of load plate give a definition of stiffness and load. The restrictor and the volume ratio of two chambers give a definition of damping ratio. The conventional model of restrictor is made of one orifice and it causes turbulent flow in the orifice at the region of large deflection. The stillness of air suing is larger and the damping is lower in the region of large deflection. In the multi-orifice case, the stiffness is similar to air spring with one orifice but damping ratio is larger than conventional air spring. And damping ratio is smaller than conventional air suing in small deflection region. Deflection is small in the region of high frequency so small damping is better than large damping. As a result, we can reduce the storage stiffness of air suing in the wide region of deflection and increase the damping ratio in the region of large deflection. After this, we will try to and the relation of Reynolds Number and Flow Resistance then we are going to make another restrictor for air spring to improve damping ratio and stiffness.

• 한국정밀공학회지
• /
• 제17권2호
• /
• pp.201-210
• /
• 2000

The large deflection of plate is analyzed by co-rotational formulations using small local displacements and rotating unit vectors on the nodal points. The rotational degrees of the freedom are represent ed by the unit vectors1 In the nodal points, and the equilibrium equations are formulated by using small deflection theories of the plates by assuming that the directions of the unit vectors of the nodal points are known apriori. The translational degrees of freedom are independently solved from the rotational degrees of freedom in the equilibrium equations, and the correct directions of the unit vectors are computed by the iterative scheme by imposing the moment equilibrium constraint. The equilibrium equations and the associated solution procedure are explained, and the verification problems are solved.

• Structural Engineering and Mechanics
• /
• 제3권2호
• /
• pp.163-172
• /
• 1995

A simple numerical method is applied to calculate the large deflection of a cantilever beam under an elastic-plastic deformation by dividing the deformed axis into a number of small segments. Assuming that each segment can be approximated as a circular arc, the method allows large deflections and plastic deformation to be analyzed. The main interests are the load-deflection relationship, curvature distribution along the beam and the length of the plastic region. The method is proved to be easy and particularly versatile. Comparisons with other studies are given.

• Steel and Composite Structures
• /
• 제14권6호
• /
• pp.605-620
• /
• 2013

This paper provides an innovative iteration technique for the large deflection problem of annular plate. After some manipulation, the problem is reduced to a couple of ODEs (ordinary differential equation). Among them, one is derived from the plane stress problem for plate, and other is derived from the bending of plate. Since the large deflection for plate is assumed in the problem, the relevant non-linear terms appear in the resulting ODEs. The pseudo-linearization procedure is suggested to solve the problem and the nonlinear ODEs can be solved in the way for the solution of linear ODE. To obtain the final solution, it is necessary to use the iteration. Several numerical examples are provided. In the study, the assumed value for non-dimensional loading is larger than those in the available references.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.387-395
• /
• 1991

Large deflection behavior of cylindrically orthotropic thin circular plates is investigated by the numerical technique of differential quadrature. Governing equations are derived in terms of transverse deflection and stress function and a Newton-Raphson technique is used to solve the nonlinear systems of equations. For small values of degree of differential quadrature (N.leq.13), as the degree of differential quadrature increases, the center deflection converges. However, as N increases further, the center deflection diverges by ill-conditioning in the weighting coefficients. As the orthotropic parameter increases, the center deflection decreases and behaves linear for the loads. At center, the stress is affected mainly by orthotropic parameter, while the stress is affected mainly by boundary condition at edge.

• Structural Engineering and Mechanics
• /
• 제51권2호
• /
• pp.333-347
• /
• 2014

Nonlinear bending of super-elliptical plates of uniform thickness under uniform transverse pressure was investigated by the Ritz method. The material was assumed to be homogeneous and isotropic. The contribution of the boundary conditions at the point supports was introduced by the Lagrange multipliers. The solution was obtained by the Newton-Raphson method. The influence of the location of the point supports on the central deflection was highlighted by sensitivity analysis. An approximate relationship between the central deflection and the super-elliptical power was obtained using the method of least squares. The critical points where the maximum deflection may develop, and the influence of nonlinearity were highlighted. The nonlinearity was found to be sensitive to the aspect ratio. The accuracy of the algorithm was validated by comparing the central deflection with the solutions of elliptical and rectangular plates.