• Journal of the Korean Wood Science and Technology
• /
• v.33 no.6 s.134
• /
• pp.25-30
• /
• 2005

This experiment was carried out for the improvement of drying schedules for 50 mm-thick Japanese red pine (Pinus densiflora Sieb. et Zucc.) lumber. Drying rates were analyzed comparatively after drying to 15% of final moisture content through the applications of conventional kiln drying schedule, time schedule, continuously rising temperature schedule, and drying rate schedule. As results drying rate of 50 mm-thick red pine lumber was 0.53%/hr with conventional kiln drying schedule, 0.9%/hr with time schedule, 2.29%/hr with continuously rising temperature schedule, and 1.52%/hr with drying rate schedule, respectively.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.61-68
• /
• 2009

This paper presents the numerical analysis of process of sludge drying to know the characteristics of design parameters and develop the new process plant. Finite volume method and $k-{\varepsilon}$ turbulence model were used to analogy the sludge drying furnace. It has been attempted to perform the disposal of sewage sludge such as simple reclaiming and dumping in sea and incineration. Currently, these methods are restricted by national or international government regulations. The drying process is adopted as an effective method for sewage sludge treatment. However sewage sludge makes it difficult to treat with a large volume at the real drying process plant because of its own complicated physical, chemical, and thermal properties. The final design value of moisture content with 10% of the dried sludge can be obtained through the simulated outputs in this study.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.33-46
• /
• 2006

This study was carried out to investigate a radio-frequency/vacuum (RF/V) drying ability and physical properties of the green boards and the pre-kiln dried boards with 40 mm thickness, and the 70 mm-thick green board of Iroko (Milicia excelsa). The major results were summarized as follows; The drying time from initial moisture content (MC) of 110% to approximate 6% MC for a 40mm-thick green board was 192 hours, and about 200 hours for the 70 mm-thick green board, respectively and so the RF/V drying times were dramatically shortened compared to conventional kiln drying time. The case hardenings at the RF/V drying completion stage test were very negligible, thus represented almost no existence of the residual stress. The checks were very slightly formed on all of the boards during the RF/V drying test, but crook appeared quite severely. During the accelerating test, the water-resistant treated specimens had not experienced any signs of checking occurred, whereas the control boards had encountered very frequent occurrences of end checking and slight surface checking. There were no observations of warping and discoloring regardless of the treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.1
• /
• pp.31-37
• /
• 1984

For the modification of kiln drying schedule, relations between resistance to drying Rd and the moisture content or drying times were found for 4/4, 6/4 and 8/4 green Douglas fir heartwood by the mild drying schedule and the severe drying schedule until the average moisture content was about 10 percent. The results of this study were as follows. 1. Resistance to drying of thicker lumber was higher than that of thinner lumber and resistance to drying of three different thicknesses were negligible between the mild-and the severe drying schedule. The relationships between resistance to drying and two schedules or three thicknesses of lumber were $Rd_1=1.830{\times}10^5\;M^{-2.24}$ for 4/4 lumber by the mild drying schedule, $Rd_2=1.822{\times}10^5\;M^{-2.25}$ for 4/4 lumber by the severe drying schedule, $Rd_3=2.352{\times}10^5\;M^{-2.14}$ for 6/4 lumber by the mild drying schedule, $Rd_4=3.457{\times}10^5\;M^{-2.27}$ for 6/4 lumber by the severe drying schedule, $Rd_5=1.317{\times}10^6\;M^{-2.56}$ for 8/4 lumber by the mild drying schedule, $Rd_6=8.267{\times}10^5\;M^{-2.40}$ for 8/4 lumber by the severe drying schedule. 2. Thinner lumber exhibited lower level of moisture content and shorter drying time required at intersection point between the moisture content and resistance to drying as a function of drying time than those of thicker lumber. Drying time of mild drying was longer than that of severe drying and similar to the level of moisture content at intersection point.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.5
• /
• pp.459-464
• /
• 2009

This study was conducted to find the relationship between the moisture content and basic density of green lumber and the final moisture content of kiln dried lumber. The possibility of using a ultrasonic nondestructive testing technology was investigated. Four matched 2-foot long boards were kiln-dried for 12, 24, 36 and 48 hours. Twenty three slices were cut to examine the distribution of moisture content along the length. It was revealed that the green weight was a better estimator of the final moisture content of the kiln-dried board than the green moisture content. The standard deviations of the moisture contents of the slices were not correlated with the final moisture contents of the kiln-dried boards. The two ultrasonic devices used for this study were apparently good tools for NDT.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.3
• /
• pp.67-81
• /
• 1989

This experiment was carried out to know the mothod of changing the step of moisture content schedule with time in conventional kiln drying. For the purpose of this object. we made drying model by applying the moisture diffusion model by J.FSiau(1984) to average moisture content equation by J.Crank(1956) derived it from Fick's second law. And to verify this method of drying model. 2.5cm-thick boards and 5.0cm-thick dimension lumbers of Pinus densiflora were kiln-dried with the schedule of T11-C3 and T10-C4, respectively. And then the drying rates were investigated and compared with those calculated from drying model. The results obtained were as follows 1. Average drying rate and total drying time of board to dry to 6.5% moisture content were 0.64%/hr and 109hr., and those of dimension lumber to dry to 8.3% moisture content were 0.4%/hr. and 162hr., respectively. 2. The moisture content of shell and core decreased by equalizing treatment and increased by conditioning treatment both on board and dimension lumber. But the moisture gradient was lower after conditioning than after equalizing. 3. As the drying was proceeded, the transverse bound water diffusion coefficient all but linearly decreased, the water vapor diffusion coefficient abruptly curvilinearly increased, while the transverse diffusion coefficient curvilinearly decreased both on board and dimension lumber. But each of diffusion coefficients on board was larger than that on dimension lumber. 4. Compared to experimential drying rate of board. theoretical drying rate was larger at 30.0%-21.8% moisture content range and was similiar at 21.8%-5.4% moisture content. And in case of dimension lumber, the drying rate was similiar at 30.0%-16.1% moisture content range but theoretical drying rate was much lower at 16.1%-8.3% moisture content range. 5. The possibility of adapting this drying model to changing the moisture content schedule step with time was in the range of 21.8%-5.4% moisture content on board. And in the case of dimension lumber that was in the range of 30.0%-16.1% moisture content.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.108-114
• /
• 2002

Red pine(Pinus densiflora) square timbers with 14.0 cm and 16.5 cm of face size and 24 m long were dried in a vacuum-press kiln and in a radio-frequency/vacuum(RF/V) kiln to compare drying rate, moisture content(MC) distribution and specific energy. RF/V drying rate was higher than vacuum-press drying rate. The effect of size of cross section on the RF/V drying rates were more pronounced than those of vacuum-press drying. The longitudinal- and the transverse MC distribution of dried square timber showed convex profile for the vacuum-press drying and concave profile for the RF/V drying. Moisture gradient of width direction was similar to the thickness direction in vacuum-press dried square timber and was more slight than that of the thickness direction in the RF/V dried large square timber. The specific energy consumption curve increased as MC decreased. Specific energy(kWh/kg of water evaporated) of the vacuum-press process required more than that of the RF/V process.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.4
• /
• pp.1-21
• /
• 1981

Exterior grades of Douglas-fir and aspen plywood were impregnated with interior fire-retardant chemicals and redried under low-, intermediate-, and high-temperature drying conditions. Fire-retardant treatments included borax-boric acid, chromated zinc chloride, minalith, pyresote, and a commercial formulation. Drying processes included kiln and press-drying. Evaluated were drying rates and defects generated. The borax-boric acid and the commercial treatments redried at rates similar to water-treated controls. Other salt treatments were significantly slower drying and more defect prone. Chromated zinc chloride treatment was consistently the slowest drying and most defect prone. Press drying was three times faster at an equivalent temperature level. However, thickness shrinkage doubled because of 50 1b/in. platen pressure.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.1
• /
• pp.52-58
• /
• 2004

Oak is one of major species in this country as well as pine, but has been less utilized because of its refractory properties. The purpose of this study is to develope an effective method for drying the boards and disks of Quercus variabilis. Among four end-coaters used in this study thick coating with polyvinyl acetate chrolide glue (PVAc) was proved as the most effective. The average air-drying rate of boards was 1.2%MC/day, which did not exceed the safe drying rate recommended by United States Department of Agriculture (USDA). The kiln drying schedule used in this study gave a good result in drying the air-dried boards to 8%MC without any internal checks. An attempt to prevent oak disks from V-cracking during air-drying using special pallet-type stickers was not successful.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.9-18
• /
• 2004

This study was carried out to find the efficient methods for preventing resin exudation from spruce board during high temperature environment service.In the dry-air oven test, in-use temperature related to resin exudation of 110℃ could be obtained by the appropriate kiln drying without any special treatment, and the in-use temperature of the radio-frequency/vacuum (RF/V)-dried boards was about 20℃ higher than that of the conventional kiln-dried boards.In the autoclave test, resin exudation was not found from any board dried in the conventional kiln and in the RF/V kiln after the low pressure steam explosion (SE) treating, while for the control resin exudations were more severe in the autoclave test above 130℃ than in the dry-air oven test. It, therefore, would be suggested that resin exudation during high temperature service condition can be prevented more effectively by super-heated steaming green boards than by high-temperature drying boards with low moisture.