• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.56-65
• /
• 1998

The bonding strength evaluation of the light weight materials for an electrical vehicle has been performed through the T-peel joint test in which the design paramete- rs such as joint style, adherend type, adherend thickness, adhesive thickness, and adhesive type are considered. It is experimentally observed that the peel strength of joint increases with the increase of the adherend thickness. With the increase of the adhesive thickness, however, the peel strength of joint increases a little. Aluminum-FRP adherend combination shows such higher peel strength than that of Aluminum-Aluminum adherend combination. For the adhesive bonded joint, the results of FEM analysis agree with those of experiment. The adhesive bonded joint reinfored with a rivet gives higher peel strength than that of the joint without rivet.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.1
• /
• pp.66-72
• /
• 1993

The brazing of Al to Al using Al-Si alloy filler metal was performed under different bonding conditions such as ratio of lap length to plate thickness, surface roughness and joint clearance of the lap joint. The adopted thickness of the base metal in this experiments were two kinds of 4mm and 7mm which were most commonly used in various field. Influence of several bonding conditions of Al/Al joint was quantitavely evaluated by bonding strength test, and microstructural analysis at the interlayer were performed by optical microscope. From above experiments, the optimum bonding conditions of the brazing bonding of Al/Al using Al-Si alloy filler metal was determined. The major results obtained are as follows. 1) The fracture occurs at brazed joint in the conditions of that the ratio of lap length to plate thickness is less than 2 in case of 7mm plate thickness. 2) The ratio of lap length to plate thickness which the fracture occurs at base metal is decreased with the decreasing of the plate thickness. 3) The joint strength is not affected by the surface roughness and joint clearance of the brazed part. 4) The heat-treatment of the brazed joint contribute to eliminate the boundary between the base metal and filler metal. However, the joint strength is not affected by the heat-treatment.

• The Journal of Korean Physical Therapy
• /
• v.32 no.6
• /
• pp.354-358
• /
• 2020

Purpose: This study aimed to verify the effects of bridge exercise with resistance to one hip joint adductor muscle on the thickness of external and internal oblique abdominal muscles, transversus abdominis muscle, and erector spinae muscle. Methods: The subjects were divided into two exercise groups: 15 for Bridge Exercise Group (BEG) and 15 for One Hip joint Adduction Bridge Exercise Group (OHABEG). The study used an ultrasonic instrument to measure trunk muscle thickness. OHABEG performed a bridge exercise with one hip Joint adduction. BEG performed a bridge exercise without resistance. Results: The external oblique abdominal, internal oblique abdominal, and the transversus abdominis muscles showed a significant increase by period and time in intra-group interactions (p<0.05), while there was no significant difference in inter-group changes (p>0.05). The erector spinae muscle had a significant increase in each period (p<0.05) but no significant difference in time, intra-group interactions, and in inter-group changes (p>0.05). Conclusion: These results demonstrated that bridge exercise with one hip joint adduction had positive effects on trunk muscle thickness. These results confirm that a bridge exercise with one hip joint adduction has a positive effect on the muscle thickness of trunk, suggesting the possibility of using it as a rehabilitation treatment for a lumbar stabilization exercise and as a basic data.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.106-114
• /
• 1995

The characteristics of adhesive bonded joint of steels for automobile were investigated. Shear and tear strength were tested and analyzed for the joints of cold rolled steel sheets bonded with three kinds of epoxy and urethane based adhesive. The results showed that the tensile shear strength and the tear strength of adhesive joint were affected by the shape of adhesive joint such as the length and width of adhesive joint. The thickness of adhesive layer was very important factor affecting the bonding strength. The shear strength increased with decrease of the thickness of adhesive layer, while the tear strength decreased as the thickness of adhesive layer decreased. In comparison with the strength of spot welded joint, the shear strength of adhesive Joint was higher than that of spot welded joint, but the tear strength of adhesive Joint was lower than that of spot welded joint.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.143-150
• /
• 1998

The evaluation of joint fatigue strength of light weight materials for electrical vehicle body has been performed through single lap joint tests with the design parameters such as joint style, adherend, bonding overlap length and bonding thickness. Fatigue strength was evaluated through 5-Hz, tension-tension, load controlled test with the stress ratio zero value. It is experimentally observed that fatigue strength of joint increases for the increase of overlap length. The combinations of Al-Al and Al-FRP adherends show that fatigue strength of joint is hardly changed for the increase of bonding thickness, but FRP-FRP adherend specimen shows that fatigue strength of joint increases after decreases for the increase of bonding thickness. Al-Al adherend specimen has much higher fatigue length than Al-FRP and FRP-FRP adherend specimens. Riveting at adgesive bonded joint gives little effect on fatigue strength.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.4
• /
• pp.905-915
• /
• 1998

Static tensile tests using adhesive-bonded single-lap joints of aluminum alloy were conducted to investigate the effect of geometric factor, overlap length, adherend thickness, adhesive thickness and material composition of adherend/adhesive on the strength of adhesive joint. The average applied shear stress at joint fracture decreased with increasing lap length. However increasing the adherend thickness resulted in a higher joint strength. Higher yield strength of adherend and lower elastic modulus of adhesive is advantageous to the adhesive joint. Newly proposed modified joint factor could be well evaluated the influence of lap length, adherend thickness and adhesive thickness on the bond strength for adhesive joints.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.2073-2078
• /
• 2015

This study is investigated for angle of elbow joint influence on grasp strength, confirm change of grasp strength and brachioradialis thickness according to angle of elbow joint in standing. Thirty male and female university students, who participated with agreement in this study, using for electronic dynamometer and convertible ultrasound measure maximum grasp strength and brachioradialis thickness after elbow joint $0^{\circ}$, $90^{\circ}$, $135^{\circ}$ positioning in standing. In average grasp strength was strongest at elbow joint $0^{\circ}$, as the angle of elbow joint increased, was decreased grasp strength, no significant statistically(p<.05). In average brachioradialis thickness was lowest at elbow joint $0^{\circ}$, as the angle of elbow joint increased, was increased brachioradialis thickness, significant statistically(p<.05). These result may indicated that change of elbow joint angle not influence on grasp strength, but influence on brachioradialis thickness.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.166-173
• /
• 1998

The evaluation of joint fatigue strength of light weight materials for an electrical vehicle body has been performed through T-peel joint tests with the design parameters such as joint style, adherend type, adherend thickness, adhesive thickness, and various adhesives. Fatigue strength was evaluated through 5-Hz, tension-tension, load controlled test with the zero stress ratio. It was observed that the fatigue strength of the joint increases with the increase of the adherend thickness. With the increase of the adhesive thickness, however, the fatigue strength of the joint increases insignificantly. An aluminum-FRP adherend combination shows much higher fatigue strength than an aluminum-aluminum adherend combination. The results of fatigue tests were found to be consistent with those of static tests.

• Journal of Welding and Joining
• /
• v.32 no.2
• /
• pp.37-42
• /
• 2014

In this study, non-load-carrying fillet welded joints fabricated using EH grade-steel are evaluated with the structural stress approach. The thickness effect was investigated by a study on welded steel joints with thickness ranging from 25 to 80mm. As-welded joint for main plate thickness of 25 to 80mm, the fatigue strength is reduced gradually. On the other hand, in case of main plate thickness of 25 to 80mm, the structural stress concentration factor increases gradually. As a result, for structural stress approach, thickness effect is not required for correction. Based on these results, a new evaluation fillet welded joint for fatigue design purposes has been proposed FAT 125.

• Transactions of Materials Processing
• /
• v.29 no.6
• /
• pp.301-306
• /
• 2020

The parametric study of Steel-Al alloy SPR joint process is based on the FE simulation described by Kim et al. [10], which was validated by comparing experimental and simulation results for two kinds of steel-Al alloy combinations according to the lower sheet thickness. To analyze the SPR joint process, the friction coefficient, the lower sheet thickness, and the rivet length were selected as the main parameters. Based on FE simulations, the effect of main parameters was investigated by measuring the interlock and the bottom thickness at the cross-sectional shape of the SPR joint. The results of simulation facilitate the design of SPR joint process in various metal combinations.