• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2132-2135
• /
• 2005

Cylindrical type air core pulse transformers capable of passing high voltage and energy pulse waveforms with high efficiency and low distortion require a much more delicate design balance of physical dimensions and electrical parameters than iron or ferrite core units. The structure of an air core high voltage pulse transformer is relatively simple, but considerable attention is needed to prevent breakdown between transformer windings. Since the thickness of the windings in spiral type is on the order of sub-millimeter, field enhancement at the edge of the windings is very high. It is, therefore, important to find proper electrical insulation Parameter to make the system compact. Several shapes of the winding are considered for air core pulse transformer development. In this paper, we are described design procedure, parameters measure and experiment results of air core type HV pulse transformer.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.6
• /
• pp.663-671
• /
• 2016

Coagulation/precipitation process has been widely used for the removal of phosphate within domestic wastewater. Although Fe and Al are typical coagulants used for phosphate removal, these have some shortages such as color problem and low sedimentation velocity. In this study, both Fe and Al were used to overcome the shortages caused by using single one, and anionic polymer coagulant was additionally used to enhance sedimentation velocity of the precipitate formed. Batch experiments using a jar test were conducted with real wastewater, which was an effluent of the second sedimentation tank in domestic wastewater treatment plant. Response Surface Methodology was used to examine the responsibility of each parameter on phosphate removal as well as to optimize the dosage of the three coagulants. Economic analysis was also done on the basis of selling prices of the coagulants in the field. Phosphate removal efficiency of Fe(III) was 30% higher than those of Fe(II). Considering chemical price, optimum dosage for achieving residual phosphate concentration below 0.2 mg/L were determined to be 18.14 mg/L of Fe(III), 2.60 mg/L of Al, and 1.64 mg/L of polymer coagulant.

• Korean Journal of Poultry Science
• /
• v.30 no.3
• /
• pp.197-202
• /
• 2003

Feeding probiotics in broiler chicks still critical in several aspects. Thus, this study was conducted to investigate the impact of feeding multiple probiotics on performance, intestinal microflora, blood cholesterol and ND antibody vaccine titer in broiler chicks. Three hundred twenty one day old male broiler chicks(cobb ${\times}$ cobb) were divided into four levels of multiple probiotics(0, 0.1, 0.2, 0.3%) with five replicates for 35 days. Basal diets contained 21.5, 19.0% CP and 3,100 kcal/kg ME for starting and finishing period, respectively. Weight gain, feed intake and feed conversion were measured weekly. The number of Salmonella, E. coli, Lactobacillus, and yeast were examined from ileum and cecum at the end of experiment. ND vaccine titer, cholesterol were detected from sera. Weight gain of birds fed probiotics were 669.33, 679.75 at the level of 0.1 and 0.2% supplemental groups for starting period. It was also improved in those treatments for finishing period and higher than control for total period. Feed conversion tended to be improved compared to that of control by the supplementation of probiotics for the first three weeks and seemed to show the similar tendency for the rest of two weeks. It was 1.611, 1.621 for the entire feeding period and improved compared with control. Total salmonella, was not decreased in ileal digesta of birds fed the probiotics compared with control, whereas the number of yeast increased in 0.1% treatment. However, the number of Lactobacillus and yeast in cecum was higher than control. Even though the blood cholesterol seem to high in 0.1% probiotics treatment, the ratio of HDL to total cholesterol showed higher than control. ND vaccine titer of birds fed probiotics were significantly higher than control (P<0.05). These results 0.1% multiple probiotics would be possible to improve the performance of broiler chicks and ND vaccine titer.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.1008-1014
• /
• 2001

Nanosize YIG powders added by Cerium which is exellent element in magneto-optical effect were synthesized by Sol-Gel method using Ethylene Glycol solvent. In 120 to 150 minute reaction time, stable sol solution which showed no change in viscosity, pH, and aging time was obtained. Monolithic YIG was synthesized at 80$0^{\circ}C$ with DTA and XRD measurement and its lattice parameter had a tendency to increase from 12.3921 $\AA$. Increasing annealing temperature from 80$0^{\circ}C$ to 105$0^{\circ}C$, average particle size was in the range of 40 nm to 330 nm. Saturation magnetization (M$_{s}$) value was increased from 18.37 to 21.25 emu/g due to enhancement of YIG crystallity and decreasing of orthoferrite phase. On the other hand, coercivity (H$_{c}$) value increased up to 90$0^{\circ}C$ and then decreased above 90$0^{\circ}C$. With increasing Ce addition, coercivity was almost not changed but saturation magnetization value was maximum at Ce 0.1 mol% and then decreased because of increasing a orthoferrite amount. Also, curie temperature (T$_{c}$) of YIG were not changed with Ce addition.ion.

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.335-340
• /
• 1998

Colossal magnetoresistance $La_{0.67}Ca_{0.33}Mn_{0.99}^{57}Fe_{0.01}O_3$ material has been produced by a metal-salt routed sol-gel process method. Magnetic properties of $La_{0.67}Ca_{0.33}Mn_{0.99}^{57}Fe_{0.01}O_3$ have been studied with x-ray diffraction, Rutherford back-scattering spectroscopy(RBS), vibrating sample magnetometer, and Mossbauer spectroscopy. Crystalline $La_{0.67}Ca_{0.33}Mn_{0.99}^{57}Fe_{0.01}O_3$ was perovskite cubic structure with a lattice parameter $a_0=3.868$\AA$$. And there was no appreciable change in the value of the lattice parameter when a small amount (x=0.01) of iron was added. However, Mossbauer and VSM data indicate the Curie temperature of the $La_{0.67}Ca_{0.33}Mn_{0.99}^{57}Fe_{0.01}O_3$ decreased from 282 to 270 k and also the saturation magnetization from 84 to 81 emu/g at 77 K. Mossbauer spectra of $La_{0.67}Ca_{0.33}Mn_{0.99}^{57}Fe_{0.01}O_3$ have been taken at various temperatures ranging form 4.2 K to room temperature. Analysis of $^{57}Fe$ Mossbauer data in terms of the local configurations of Mn atoms has permitted the influence of the magnetic hyperfine interactions to be monitored. The isomer shifts show that the charge state of all Fe ions are ferric. The magnetoresistance of $La_{0.67}Ca_{0.33}Mn_{0.99}^{57}Fe_{0.01}O_3$ was about 33 % at semiconductor-metal transition temperature $T_{SC-M}=250K$.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.4
• /
• pp.349-355
• /
• 2015

Underwater robots generally show better performances for tasks than humans under certain underwater constraints such as. high pressure, limited light, etc. To properly diagnose in an underwater environment using remotely operated underwater vehicles, it is important to keep autonomously its own position and orientation in order to avoid additional control efforts. In this paper, we propose an efficient method to assist in the operation for the various disturbances of a remotely operated vehicle for the diagnosis of underwater structures. The conventional AHRS-based bearing estimation system did not work well due to incorrect measurements caused by the hard-iron effect when the robot is approaching a ferromagnetic structure. To overcome this drawback, we propose a sensor fusion algorithm with the camera and AHRS for estimating the pose of the ROV. However, the image information in the underwater environment is often unreliable and blurred by turbidity or suspended solids. Thus, we suggest an efficient method for fusing the vision sensor and the AHRS with a criterion which is the amount of blur in the image. To evaluate the amount of blur, we adopt two methods: one is the quantification of high frequency components using the power spectrum density analysis of 2D discrete Fourier transformed image, and the other is identifying the blur parameter based on cepstrum analysis. We evaluate the performance of the robustness of the visual odometry and blur estimation methods according to the change of light and distance. We verify that the blur estimation method based on cepstrum analysis shows a better performance through the experiments.

• Clean Technology
• /
• v.21 no.2
• /
• pp.96-101
• /
• 2015

Hematite reduction using hydrogen was conducted and the various process parameters were closely observed. A lab scale fluidized bed unit was designed especially for this study. The optimal values of the gas velocity, reduction time and temperature were evaluated. The values which indicated the highest reduction rate were set as fixed parameters for the following tests starting with the reduction time of 30 minutes and 750 ℃ of temperature. Among these variables the one with the highest interest was the gas specific consumption. It will tell the amount of the gas which is required to achieve a reduction rate of over 90% at the optimal conditions. This parameter is important for the scale up of the lab scale unit. 1,500 Nm³/ton-ore was found to be the optimal specific gas consumption rate at which the reduction rates exhibit the highest values for hematite.

• Journal of Korea Soil Environment Society
• /
• v.2 no.3
• /
• pp.31-38
• /
• 1997

Temporal and spatial comparisons of acid mine drainage contaminated waters are difficult because of the complex physico-chemical nature of the pollutant. In the present study, an acid mine drainage index has been developed and evaluated for the assessment of surface waters. AMD index is calculated using a modified arithmetic weighted index using seven parameters which are most indicative of AMD contamination, i. e. pH value, sulphate, iron, zinc, aluminum, copper and manganese. Weighting is used to express the relative indicator value of each parameter. The proposed AMD index is used to quantify contamination from acid mine drainage over ten different old mine sites and assess the degree of impact on surface on surface waters. As a result of AMD evaluation, the Sukbong Mine located near the Moonkyung province showed lowest AMD value indicating the worst acid mine drainage quality. In overall, Youngdong mine sites showed higher contaimination compared to the other mine sites including Youngsuh, Choongbu, Suhbu and Nambu area.

• Journal of the Mineralogical Society of Korea
• /
• v.9 no.2
• /
• pp.55-63
• /
• 1996

Epidote occurs as veinlets in the propylitic alteration zone of the Bobae clay deposit, Pusan, Korea. Its cell parameters apparently decrease with the contents of Al, Fe, and Ca. Fourier transform infrared (FTIR) spectra show one hydrosyl environment related to AlM2 at 3357-3358 cm-1. In the mid-infrared region, the peaks at 950 and 1030 cm-1 sharper with increasing Al shifting to higher energy region. The peak at 885 cm-1 shifts slightly to a lower energy region with a decreasing intensity as the Fe content increases. In the far-IR region, epidote exhibits absorption bands at 120 and 140 cm-1, which are related to the Ca-O bonds in A-sites.M ssbauer spectra of epidote show that the isomer shifts of Fe3+ range from 0.36-0.37 at the M3 site and from 0.35-0.44 at M1 site. Fe2+ shows the isomer shift ranging from 1.11 to 1.13. Quadrupole splitting is 2.04 for Fe3+M3, 0.52-0.70 for Fe3+M1, and 2.61-2.70 for Fe2+M3. Calculation shows Fe3+M386-90.7%, Fe3+M12.5-3.6%, and Fe2+M35.8-11.4% of total iron, showing preferential distribution of Fe3+ in the M3 site. The Fe3+M3 content is between 0.486 and 0.513 per formula unit. in the Fe-rich epidote, less Fe3+ and more Fe2+ are accommodated in the M1 and M3 sites. Hence, the overall disorder increases as total Fe content increase. The ordering parameter of the Bobae epidote is 0.93-0.95, suggesting a disequilibrium state below 200$^{\circ}C$. The constant temperature over a long period may be essential for the transition from disordered state to equilibrium state, despite the possible variation in flux and composition of the hydrothermal fluid.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.676-680
• /
• 2003

Dissolution of magnetite powders by 0.05 M citric acid was investigated at $50^{\circ}C$. All the tests were performed in the pH range between 2.0 to 5.0, which was adjusted using nitric acid or sodium hydroxide. Concentration of each of the dissociated chemical species of citric acid under various solution pHs was calculated using the ionization constants. Variation of zeta potential of magnetite with pH changes was also investigated. The dissolution reaction was explained by comparing the concentration of the dissociated chemical species of citric acid with the zeta potential. Longer than 3 h of induction time was required to dissolve the magnetite. The dissolution behaviour of magnetite was well described by the equation. The physical meaning of each parameter was explained successfully from the model equation.