• Journal of the Korean Chemical Society
• /
• v.40 no.5
• /
• pp.341-346
• /
• 1996

Electrochemical determination of iodide was carried out by stripping voltammetry with a $(Cin)Cu(NO_3)_2$ modified-carbon paste electrode. Iodide was coordinated onto the electrode surface containing $(Cin)Cu(NO_3)_2$ via ion exchange. The oxidation peak potential of incorporated iodide was ＋0.72 V. The optimum analytical conditions for the determination of iodide were investigated using linear sweep voltammetry. Optimum conditions for the electrochemical determination of iodide were as follows: i) A predeposition solution was 0.1 M $KNO_3.$ ii) The deposition time was 10 min. iii) The composition of the electrode was 40% (w/w). The detection limit for iodide was $1.0{\times}10^{-6}M$ and the relative standard deviation was ${\pm}5.5%\;in\;2.0{\times}10^{-5}M$(four repetitions). The interference effect of other anions were also investigated. $Cl^-,\;Br^-,\;C_2O_4^{2-},\;and\;ClO_4^-$ ions do not interfere for the determination of iodide. When $SCN^-$ was added to the deposition solution, the oxidation peak current of iodide ion was decreased roughly 32%.

• Analytical Science and Technology
• /
• v.15 no.5
• /
• pp.445-450
• /
• 2002

A sensitive gas chromatographic method has been established for the determination of total iodide in seawater as their volatile organic derivative. The method is based on the formation of 4-iodo-2,6-dimethylphenol with 2,6-dimethylphenol in matrix and a single-step extraction of the derivative with ethyl ether, which are then measured by gas chromatography-mass spectrometry (selected ion monitoring). Iodate in sea water was completely reduced to iodide with ascorbic acid and acetic acid. The detection limit was 0.1 ng/mL in seawater and the calibration curve showed good linearity with r=0.9997. The method was sensitive, reproducible and simple enough to permit the reliable routine analysis of total iodide in seawater. Total iodide in sea water was found about 30 ng/ml.

• Analytical Science and Technology
• /
• v.14 no.4
• /
• pp.306-310
• /
• 2001

Ion chromatography was applied to determine iodide remained in sulfuric acid aqueous solution after adsorption procedure. Iodide was determined in 0.25 M, 0.5 M and 1 M sulfuric acid solution on time variation. Because sulfuric acid in solution plays as an oxidizer, the concentration of iodide decreased with increasing concentration or sulfuric acid. Thereafter, sulfuric acid was neutralized with sodium hydroxide. Good linearity(r=0.99999) was obtained at the range of 0-20 mg/L 1 in 0.5 M sodium sulfate matrix.

• Analytical Science and Technology
• /
• v.12 no.2
• /
• pp.99-104
• /
• 1999

A stepwise gradient elution with two wavelengths detection was performed for the separation and determination of some anions in saline water. The eight anions such as iodate, bromate, nitrite, bromide, nitrate, chromate, iodide and thiocyanate were successfully separated using AS-7 column and sodium chloride/sodium phosphate buffer solution as an eluant within 40 min. The separation behaviors of anions were studied at various sodium chloride concentrations. The peak shapes of anions of bromate, nitrite, bromide and nitrate gradually broadened as the concentration of sodium chloride increased until 1.0 M in the sample solutions. However, no effect was observed in the peak shapes of chromate, iodide and thiocynate. A good linearity was obtained at the range of ppm(mg/L). The detection limit was proved to be $10-720{\mu}g/L$ for the eight anions with $50{\mu}L$ injection volume. This method was applied to the determination of $Br^-$, ${NO_3}^-$ and $I^-$ in sea water.

• Analytical Science and Technology
• /
• v.13 no.3
• /
• pp.304-308
• /
• 2000

The iodide was recovered from a simulated spent fuel to the sodium bisulfite aqueous solution. It was discussed that the trace iodide (below 1 ppm) was determined without the matrix effect of 0.1 M sodium bisulfite and 1 mM $HNO_3$ in aqueous solution by ion chromatography with UV detection. AS4A-SC (DIONEX) column and UV-absorption spectrophotometer were used. The UV-absorption spectra of sodium bisulfite, nitric acid and iodide were obtained, and then 230 nm was selected as an absorption wavelength for iodide determination. 0.1 M NaCl eluent was optimum condition. In this condition the calibration curve of iodide was obtained on the range of about 0-1,000 ppb. The linear coefficient was 0.99993 and the detection limit was 5 ppb. The relative standard deviation was 1.26%.

• Journal of the korean veterinary medical association
• /
• v.8 no.6
• /
• pp.15-19
• /
• 1964

1. Sodium Citrate, Sodim Iodide, Gelatine and Vitamin-K were administered to the dogs in the purpose of determination of blood Coagulation time effected by these hemostatic agents, In this study 6 heads of dogs were used and the results obtained in this e

• Analytical Science and Technology
• /
• v.7 no.3
• /
• pp.261-269
• /
• 1994

The iodide formed stoichiometrically for sulfide by its oxidation with iodate was extracted as an ion-pair with methylene green into 1,2-dichloroethane and the extract was measured spectrophotometrically at 656nm for the determination of sulfide. Hydrogen sulfide separated from the sample matrix was introduced into a solution containing pH 3.5 acetate buffer and iodate, in which the hydrogen sulfide was completely converted into iodide. A linear calibration graph was obtained over the range $3{\times}10^{-7}{\sim}1.2{\times}10^{-5}M$ sulfide($0.0096{\sim}0.384{\mu}g$ of $S^{2-}/ml$) and the detection limit was $0.0032{\mu}g/ml$. The apparent molar absorptivity and a correlation coefficient(r) were $6.7{\times}10^4L\;mole^{-1}\;cm^{-1}$ and 0.999, respectively. When applied to the stream water samples, the proposed method gave a relative standard deviation of 1.59% at $5{\times}10^{-6}M$ sulfide level.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.632-635
• /
• 2003

For the disposal of low-level radwaste from nuclear power plant need the determination of levels of radio nuclides in radwaste. These nuclides include the difficult-to-measure nuclides, so indirect methodology for the determination of the difficult-to-measure nuclides have to be developed. In this work, for the determination of $^129I(t_{1/2}=1.57{\times}10^7 years)$ in low-level radwaste from nuclear power plant is investigated. Recovery of Iodide in simulated waste($UO_2$ pellet) as a soluble and radwaste(resin, woolen fabric)as a insoluble samples are measured. After pretreatment of sample, $I_2$ are extracted from aqueous solution with $CCl_4$. Then I are extracted from $CCl_4$ with 0.1M $NaHSO_3$ aqueous solution. iodide in aqueous solution are determined by ion chromatography. The overall recovery yield is 76.7 (RSD 1.7%) for mixed-acid digestion method. Incase of woolen fabrics, overall recovery yield is 74.3 (RSD 2.2%) and recovery of iodide in resin 56.5(RSD 5.6%) for alkaline fusion method.

• Analytical Science and Technology
• /
• v.16 no.2
• /
• pp.110-116
• /
• 2003

A study has been done on the separation of iodide from spent pressurized water reactor (PWR) fuels and its quantitative determination using ion chromatography. Spent PWR fuels were dissolved with mixed acid of nitric and hydrochloric acids (80 : 20 molL%) which can oxidize iodide to iodate to prevent it from be vaporized. After reducing ${IO_3}^-$ ­to $I_2$ in 2.5 M $HNO_3$ with $NH_2OH{\cdot}HCl$, Iodine was selectively separated from actinides and all other fission products with carbontetrachloride and back-extracted with 0.1 M $NaHSO_3$. Recovered iodide was determined using the ion chromatograph of which the column was installed in a glove box for the analysis of radioactive materials. In practice, spent PWR fuel with 42,000~44,000 MWd/MtU was analyzed and its quantity was compared to that calculated by burnup code, ORIGEN2. The agreement was achieved with a deviation of -8.3~-0.5% from the ORIGEN 2 data, $324.5{\sim}343.6{\mu}g/g$.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.10
• /
• pp.1529-1532
• /
• 2005

A simple and cost effective method for separation and preconcentration of Ag(I) at the $10^{-7}\;mol\;L^{-1}$ level in the environmental and mineral samples is present. The method is based on the flotation of Ag(I)-iodide complex as an ion-associate with ferroin in pH of 4 from a large volume of an aqueous solution (500 mL) using nheptane. The floated layer was then dissolved in dimethylsulfoxide (DMSO) for the subsequent spectrophotometric determination. Beer's law was obeyed over a range of 2.0 ${\times}$ $10^{-7}$-4.0 ${\times}$ $10^{-6}$ mol $L^{-1}$ with the apparent molar absorptivity of 2.67 ${\times}$ $10^5$ L $mol^{-1}\;cm^{-1}$. The detection limit (n = 5) was 4 ${\times}$ $10^{-8}$ mol $L^{-1}$, and RSD (n = 5) obtained for 2.0 ${\times}$ $10^{-6}$ mol $L^{-1}$ of Ag(I) was 2.2%. The interference effects of a number of elements was studied and found that only $Hg^{2+}$ at low concentration, and $Pb^{2+}$, $Cd^{2+}$, $Cu^{2+}$, and $Fe^{3+}$ ions at moderately high concentrations were interfered. To overcome on these interference effects, the solution was treated with EDTA at a buffering pH of 4 and passed through a column containing Amberlite IR-120 ionexchanger resin, just before the flotation process. The proposed method was applied to determine of Ag(I) in a synthetic waste water, a photographic washing sample and a geological sample and the results was compared with those obtained from the flame atomic absorption spectrometry. The results were satisfactorily comparable with together, so that the applicability of the proposed method was confirmed in encountering with the real samples.