• 한국기계가공학회지
• /
• 제9권5호
• /
• pp.40-49
• /
• 2010

Conical involute gears are being used for marine gearboxes, automotive transmissions, and robots, and so on, but not much. As involute profile gear, conical involute gear not only can be engaged with spur and helical gear but also can be used for power transmission of parallel, crossed and skewed axis with small angle. Hence, conical involute gears are likely to develop in future. Through a study on the basic theory of conical involute gear, tooth surface compressive stress analysis was performed by using commercial modeling program, comparing before and after profile modification. As a result, it noticed that tooth profile modification is able to relieve more tooth surface compressive stress than before modification.

• 대한기계학회논문집
• /
• 제9권5호
• /
• pp.572-578
• /
• 1985

본 논문에서는 인벌류우트와 원고치형의 단점을 보완하고 양자의 장점을 취한 치형을 얻기위하여 피치점 부근에서는 인벌류우트치형으로 이끝부분에서는 원호로 하 고 이뿌리부분에서는 상대방 기어의 원호부분과 맞물릴 수 있는 곡선으로 하는 치형을 합성하고, 이 합성치형의 유효치형을 가공할 수 있는 랙치형을 이론적인 방법으로 구 하였다. 그리고, 이 합성치형의 유효치형에 대한 이끝과 이뿌리 두께의 변화와 물림 률을 검토하였다.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.198-204
• /
• 1987

본 논문에서는 전보에서 창성된 인벌류우트-원호합성치형기어에 있어서 Hertz 식에 의하여 치면접촉응력을 구하고 유한요소법에 의하여 이뿌리응력을 계산하였다. 그리고 같은 제원의 표준 인벌류우트 치형기어와 비교하였다.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.870-875
• /
• 1986

본 연구에서는 랙의 이끝부분을 full-rounded tip으로 설계한 후, 이에 의하 여 창성되는 피니언의 이뿌리곡선을 구하여 전체치형을 완성하였다. 그리고 합성치 형기어의 미끄름율, 유효이뿌리원에서의 공칭굽힘응력과 두쌍접촉호의 길이대 원호부 분접촉호의 길이의 비인 접촉계수를 해석적인 방법으로 구하였다.또한 이들 특성들 과 물림율등 제특성을 비교.검토하여 공구압력각, 인벌류우트부분의 크기를 나타내는 물림각 및 원호반경등의 변화에 대한 제특성의 변화를 고려한 합성치형의 성능을 향상 시킬 수 있는 설계방법을 구하였으며, 합성치형과 표준인버류우트치형을 비교하였다.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.129-135
• /
• 1996

The area of gear vibration and noise, has recently been the focus of many studies. The proper kinematic and geometric design of gears, the mathematical modeling of gear system are essential for a good design. This work present a gear disign for reducing noise, and practical approaches used for machinery noise reduction slong with the summary of methods available for predicting gear noise in terms of the transmis- sion error, and show a comparative study with other methods. A new tooth profile modification is proposed for reducing vibration and noise of involute gears. The method is based on the use of cubic spline curves. The tooth profile is constrained to assume an involute shape during the loaded operation. Thus the new gear profile assures conjugate motion at all points along the line of action. The new profile is found to result in a more uniform static transmission error compared to not only standard involute profile but also modificated profile therby contributing to the improvement of vibration and noise characteristics of the gear.

• 한국정밀공학회지
• /
• 제1권3호
• /
• pp.85-94
• /
• 1984

The WILDHABER-NOVIKOV gear, one of the circular arc gears, has the large contact area between the convex and concave profiled mating teeth, moves from one end of the tooth to the other axially making a face contact. Hence it provides a large load capacity than the Involute gear and still satisfying the law of gearing. In order to analyze the gear stress, a photoelastic investigation was carried out. Photo elastic model of the WILDHABER-NOVIKOV gears were made of Araldite CT200 in this investigation. For both the many teeth gear and the few teeth gear segments, External gears of all addendum type WILDHABER-NOVIKOV gear and the involute gear were tested. Included were the models with various profile raddi at the same pressure angle 20 .deg. and module 13.5. The flank stresses and fillet stresses of these gears were observed in each case and compared with those of gears. From this investigation, the following results were obtained. A. In the case of having many teeth gear: As the profile radius is increased, the fillet stresses of the WILDHABER-NOVIKOV gear become the same or less than that of the INVOLUTE gea, and the flank stress becomes smaller than that of the INVOLUTE gear. Therefore the better design condition is satisfied with a large profile radius. B. IN the case of having a few teeth gear: As the profile radius is increased the flank stress of WILDHABER-NOVIKOV gear becomes smaller than that of the INVOLUTE gear, but the fillet stresses become larger than that of the INVOLUTE gear. Therefore the larger design condition is satisfied with small profile radius.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.296-303
• /
• 1987

본 논문에서는 동력전달용 기어에 주로 쓰이는 물림률 1.3 이상일 때, 치면접 촉응력과 공칭굽힘응력이 작게되는 풀림각 1˚로 고정하여 잇수 30∼100개 압력각 14˚∼30˚의 범위에서 최소 원호반경식과 치형 조건을 만족하는 최대 원호반경식에 대하여 고찰하였다.

• 한국정밀공학회지
• /
• 제15권5호
• /
• pp.85-92
• /
• 1998

This present paper describes a mathematical model of profile shifted elliptical gears, and this model is based on the concepts of envelope theory and conjugate geometry between the blank and the straight-sided rack cutter. The geometric model of the rack cutter includes working regions generating involute curves and fillets for trocoidal curves, and furthermore the addendum modified coeff. is considered for avoiding undercutting. The addendum modified coeff. is changed linearly along with pitch curves and must be the same absolute value at both major semi-axis and minor semi-axis. If undercutting is at all pronounced, the undercut tooth not only are weakened in strength, but lose a small portion of the involute adjacent to the base circle, then this loss of involute may cause a serious reduction in the length of contact. A very effective method of avoiding undercutting is to use the so-called profile shifted gearing. Non-undercutting condition is examined with the change of eccentricity and addendum modified coeff. in elliptical gears and then the minimum number of tooth is proposed not to gernerate undercutting phenomenon.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.369-374
• /
• 2001

Gear is general mechanical elements that used for power transmission between two shafts that interval is comparatively short. and it delivers big power as accurate ratio of speed. The profile of Spur gear which is the most basic factor is divided into Trochoidal fillet curve and Involute curve. Involute curve is used a lot of a shaped curve of machine parts such as a gear, a scroll compressor and a collar of centrifugal pump. However, it is poor to study the modeling of Trochoidal fillet curve and the three dimensions model shaped mathematical curve. This paper describes a mathematical model of profile shifted involute gear. and this model is based on Camus's theory. We draw three dimensions gear have accurate mathematical function using ADS, VisualLISP. and To check accuracy and perfection, we make a program of checking Interference. and use for this study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.1008-1012
• /
• 1997

This study is on a mathematical model of profile shifted involute gear, and this model is based on Camus's theory. Gear is general mechanical elements that used for power transmission between two shafts that interval is comparatively short. and it delivers bit power as accurate ratio of speed. The profile of Spur gear which is the most basic factor is divided into Trochoidal fillet curve and Involute curve. Involute curve is used a lot of a shape curve of machine parts such as a gear, a scroll compressor and a collar of centrifugal pump. However, It is poor to study the modeling of Trochoidal fillet curve and the three dimensions model shaped mathematical curve. So we draw three dimensions gear have accurate mathematical function using ADS(Automatic Drawing system), VisualLISP. To check accuracy and perfection, we make a program of checking Interference. and use for this study.