• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.7A
• /
• pp.678-682
• /
• 2011

In this paper, a compact log periodic dipole array (LPDA) antenna operating from 1 to 6 GHz is studied. Inverted-L shaped dipole elements are used to miniaturize the lateral size of an LPDA antenna and the spacing factor is also decreased to reduce the total length of the LPDA antenna. As the top-loading length of the inverted-L shaped dipole elements is increased, the width of the LPDA antenna is decreased but the bandwidth and the gain of the antenna are decreased. The fabricated compact LPDA antenna is printed on FR4 substrate With a dielectric constant of 4.4 and a thickness of 1.6 mm, and its size is reduced to 32% in width and 49% in length compared to a standard LPDA antenna.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.1
• /
• pp.37-44
• /
• 2020

In this paper, we proposed a compact printed monopole antenna with an inverted L-shaped slot for dual-band operations. Two operating frequency bands are achieved with the use of an inverted L-shaped slot etched on the radiating strip for bandwidth enhancement and a defected ground structure for return loss improvement in the higher frequency band. The measured results showthat the proposed antenna has impedance bandwidths (S₁₁< -10 dB) of 270 MHz (1.81-2.08 GHz) and 340 MHz (2.36-2.70 GHz), covering the required bandwidths for PCS (1850.5-1989.5 MHz), CDMA 2000 (1850-1990 MHz), TD-SCDMA (1880-2025 MHz) and 2.4 GHz WLAN (2400-2484 MHz). The measured return loss of the proposed antenna has a good value of approximately 27.2 dB at 2.4 GHz WLAN. The antenna's peak gains also have a high value of 1.92 dBi at 2 GHz and 2.12 dBi at 2.45 GHz. The proposed antenna shows omnidirectional radiation patterns over the entire frequency range of interest.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.39-46
• /
• 2014

In this paper, to operate 2.4 GHz Inverted-L antenna with On-Board Broadband characteristics is proposed. The antenna was designed on the system board, the bandwidth by adjusting the reactance of the antenna that was formed common-mode and differential-mode on the antenna stubs has been improved. The system size is $80mm{\times}60mm$, the size of the antenna was limited to $30mm{\times}60mm$, the thickness of FR4 dielectric substrate is 0.8 mm, FR4 dielectric constant 4.4 is used. The experimental results, the bandwidth from 17.2 to 24.1 %, the gain is 3.01~4.71 dB, omni-directional radiation pattern characteristics were obtained. By a mobile terminal design applying the results of the paper, the handset's price competitiveness and production efficiency can be improved.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2004.12a
• /
• pp.43-51
• /
• 2004

Input impedance of the inverted L antenna which is modified from a monopole antenna varies to very high input impedance value when the ration of vertical height to horizontal length is reduced. So its impedance matching becomes very difficult. In this paper, we analyzed the input impedance variation range depending on the ratio of vertical height to horizontal length in the normal and ferrite thin film added configuration for the input impedance control. For the exact analysis involving the permittivity, permeability and conductivity of ferrite material, FDTD numerical method is used.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.1
• /
• pp.18-22
• /
• 2013

Input impedance of the inverted L antenna which is modified from a monopole antenna varies to very high input impedance value when the ratio of vertical height to horizontal length is reduced. So its impedance matching becomes very difficult. In this paper, we analyzed the input impedance variation range depending on the ratio of vertical height to horizontal length in the normal and ferrite thin film added configuration for the input impedance control. For the exact analysis involving the permittivity, permeability and conductivity of ferrite material, FDTD numerical method is used.

• Journal of information and communication convergence engineering
• /
• v.10 no.4
• /
• pp.321-328
• /
• 2012

A novel design for a simple rectangular ring with open-ended monopole antenna wireless local area network (WLAN) applications is proposed in this article. The proposed antenna consists of an open-ended rectangular ring, an inverted L-strip, and a rectangular slit in the ground plane, and is fed by a 50 ${\Omega}$ microstrip feed-line. Prototypes of the proposed antenna were designed, fabricated, and tested. Experimental results show that the proposed antenna receives 2.3125-2.775 GHz and 4.8625-6.7125 GHz with a return loss less than -10 dB, covering the required bandwidths of the 2.4/5.2/5.8 GHz WLAN standards. Meanwhile, the 2D radiation patterns and 3D gain performance of the antenna in the operation bands were also observed and discussed.

• Resources Recycling
• /
• v.13 no.6
• /
• pp.26-30
• /
• 2004

Input impedance of the inverted L antenna which is modified from a monopole antenna varies to very high input impedance value when the ratio of vertical height to horizontal length is reduced. So its impedance matching becomes very difficult. In this paper, we analyzed the input impedance variation range depending on the ratio of vertical height to horizontal length in the normal and ferrite thin film added configuration for the input impedance control. For the exact analysis involving the permittivity, permeability and conductivity of ferrite material, FDTD numerical method is used.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.4
• /
• pp.165-169
• /
• 2011

In recent years mobile phone handset terminal has tended to have additional various functions and slim and light weight, and its internal space is getting smaller and narrower. According to complex parts, small and narrow inner space is caused not sufficient bandwidth and lower impedance. Moreover, additional polarization loss by the surrounding parts produces is lower effectiveness and increases difficulties for getting the antenna gain. For IFA is low profile structure based on the ILA(Inverted L Antenna) which is transformed from the monopole antenna. While this antenna has lots of advantages in internal antenna of mobile phone, it has some disadvantage of reduced bandwidth and gains compared with monopole antenna. In this paper, propose vlade hybrid antenna use for the coupling structure.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.5 no.1 s.9
• /
• pp.65-70
• /
• 2006

A UHF band RFID passive tag antenna, which can be attached on metallic objects, is proposed. The proposed tag antenna is more insensitive to the size of the metallic object than conventional PIFAs or IFAs. It is constructed on a multi-layer and its size is reduced by using a 'L' slit. Performances of the antenna is analyzed by Ansoft's HFSS and measured using a back-scattering method. The simulated and measured data are obtained with varying the size of metallic object.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.888-896
• /
• 2011

In this paper, we studied characteristics of the bent antenna febricated on Flexible-PCB. Flexible-PCB consisting of a polyimide has dielectric constant 3.5, thickness 0.125 mm. Proposed antennas which operates at Bluetooth band are a rectangular loop antenna and a loop antenna with inverted-L type stub. We compared the input matching and radiation characteristics of the proposed antennas under eight kinds of bending conditions.