• Journal of the Speleological Society of Korea
• /
• no.85
• /
• pp.1-14
• /
• 2008

Electroluminescent Display(ELD) will be the innovative ideas to replace existed electricity illumination systems that consider to under effectiveness and environmental pollution generators in the commercial caves because ELD has less heat and low electricity consumption by the new illumination materials. Characteristics of the ELD are as following: it is a proper matter for the small merchandise ads due to its thickness is only below 3oo micoron, electricity consumption of ELD is less (1/3) than LED, ELD that is a whole face illumination system is much brighter than LED that is a dot illumination system, ELD is longer life than others due to its less light generation systems, ELD is any problems to bend, and it is a best device to use a light board ads. ELD has advantages on conservation of cave biosystems and reduce pollution when ELD is installed in touring spots and emergency corridors of weak illuminated cave internal areas by less heating and low electricity consumption using the indirect illumination of the ELD. Therefore when the high technologic ELD is installed in the commercial caves in Korea, it will be innovating cave environmental systems, saving budgets, and increasing tours.

• KIEAE Journal
• /
• v.2 no.2
• /
• pp.33-38
• /
• 2002

There are a number of practical uses for devices which are capable of piping large amounts of light: illumination of areas where there would be maintenance, safety, or security problems with electronic light sources; piping sunlight into indoor areas for illumination; and the conversion of high luminous efficacy, good color quality, high intensity discharge lamps into more acceptable linear of area sources of light. Prism light guides are hollow structures which pipe light by means of total internal reflectin(TIR). These devices are unique in their ability to combine the efficiency of TIR with the relatively low cost of hollow structure. An important application stems from their ability to transform a point source of light such as an incandescent or discharge lamp into a linear or area source of light or illumination. We report the development of an economical, flexible prismatic film for fabricating the light guide wall. This guide geometries and films are currently under development.

• ALGAE
• /
• v.24 no.2
• /
• pp.121-127
• /
• 2009

The unicellular green alga, Haematococcus pluvialis, accumulates the highest level of astaxanthin among knownastaxanthi.n-producing organisms. Light is the most important factor to induce astaxanthin by H. pluvialis. BIue andred LEDs, whose ${\lambda}_{max}$'s are 470 and 665 nm, respectively, were used for internally illuminated light sources.Fluorescent lamps were also used for both internal and external illumination sources. The astaxanthin levels in thesevarious lighting systems were analyzed and compared each other. The cultures under internally illuminated LEDsaccumulaled 20% more astaxanthin than those under fluorescent lamp. Furthermore, LEDs generated much lessheat than the fluorescent lamps, which gives one more reason for the LEDs being a suitable internal Light source forastaxanthin induction. The results reported here would lead novel designs of photobioreactors with improvementsof illumination methods for high level of astaxanthm production. The maximum astaxanthin concentrations as wellas the astaxanthin yield per supplied photon were increased by at least 20% when blue or red LEDs were supplied.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.4
• /
• pp.1-7
• /
• 2009

This study investigated the actual conditions of the illumination environment from agricultural youth study room. The result, average space of the study room was 11.42[$m^2$]. The illuminant uses the fluorescent lamp mainly, Method of using illumination was only general illumination the case which uses 73.8[%]. Method of light distribution was a direct lighting mainly. The house which has a stand illumination was also 45.7[%], The percentage using the stand illumination which was a local illumination was nothing but in 20[%] of the whole subject of investigation, therefore eye work could not effective. The internal illuminance was average 131.82[lx], the desk illuminance was 253.64[lx] which was the minimum permitted limit and poor. Uniformity ratio of illuminance appeared with average 35.61[%]. The satisfaction with 3.93 points to be high for illumination environment, therefore it was thought that the recognition of illumination was very insufficient.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.9
• /
• pp.424-433
• /
• 2014

The purpose of this study is to evaluate the effectiveness in the lighting performance of mixed type light-shelf, by comparing and analyzing the internal light-shelf, external light-shelf, and mixed-type light-shelf. The performance of light-shelf was evaluated according to the angle of light-shelf at summer solstice, winter solstice, vernal equinox, and autumn equinox. The comparative analysis between the internal light-shelf, external light-shelf, and mixed-type light-shelf was carried out using the performance evaluation and analysis method. The result of performance evaluation is shown as follows. The mixed type light-shelf showed the highest lighting performance all at summer solstice, winter solstice, vernal equinox, and autumn equinox, followed by the external light-shelf and the internal light-shelf in the same order. The mixed type light-shelf was the most favorable for bringing daylight to indoors by adjusting the angle of light-shelf, and it also showed the highest lighting performance in terms of uniformity ratio of illumination which indicates the quality of light.

• Journal of the Institute of Convergence Signal Processing
• /
• v.11 no.1
• /
• pp.13-18
• /
• 2010

Most of the research in the multi-touch area is based on the FTIR(Frustrated Total Internal Re리ection), which is just implemented by using the previous approach. Moreover, there are not the software solutions to improve a performance in the multi touch-blobs detection or the user gesture recognition. Therefore, we implement a multi-touch table-top display that is based on the DI(Diffused Illumination), the improved touch-points detection and user gesture recognition. The proposed method supports a simultaneous transformation multi-touch command for objects in the running application. Also, the system latency time is reduced by the proposed ore-testing method in the multi touch-blobs detection processing. Implemented device is simulated by programming the Flash AS3 application in the TUIO(Tangible User Interface Object) environment that is based on the OSC(Open Sound Control) protocol. As a result, Our system shows the 37% system latency reduction, and is successful in the multi-touch gestures recognition.

• Journal of the Optical Society of Korea
• /
• v.20 no.5
• /
• pp.614-622
• /
• 2016

In this paper, we propose a novel differential equation method for designing a total internal reflection (TIR) LED lens with double freeform surfaces. A complete set of simultaneous differential equations for the method is derived from the condition for minimizing the Fresnel loss, illumination models, Snell’s Law of ray propagation, and a new constraint on the incident angle of a ray on the light-exiting surface of the lens. The last constraint is essential to complete the set of simultaneous differential equations. By adopting the TIR structure and applying the condition for minimizing the Fresnel loss, it is expected that the proposed TIR LED lens can have a high luminous flux efficiency, even though its beam-spread angle is narrow. To validate the proposed method, three TIR LED lenses with beam-spread angles of less than 22.6° have been designed, and their performances evaluated by ray tracing. Their luminous flux efficiencies could be obviously increased by at least 35% and 5%, compared to conventional LED lenses with a single freeform surface and with double freeform surfaces, respectively.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.9
• /
• pp.604-609
• /
• 2011

The increased quality of life requires indoor illumination environment to have illumination with higher intensity. The increase in indoor illumination goes hand in hand with increase in indoor heat load. Of late, the internal heat in the cooling load has been growing gradually and the proportion of the lighting load has been bigger in the cooling load. The objective of the experiment here is to estimate the proper exhaust air flow displacement to remove heat from different types of lighting equipment. The heat causing the cooling load in lighting equipment is the ratio of heat per watt and the ratio of space for heat. Experimental measurements of the constant temperature and humidity in chambers that exhaust air flow by changing the exhaust calorific value was measured. Using the Airflow exhaust heat from lighting fixture of this study should help to reduce House cooling load.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2000.04a
• /
• pp.62-66
• /
• 2000

This study investigated the effects of certain specific wavelengths of lighting on the autonomic nervous system (ANS) using the heart rate variability (HRV) as an index. Six subjects with normal color vision participated n this study between 15:00 and 17:00 hr to neutralize any visual differences arising from circadian rhythm. The environmental conditions of the laboratory were maintained in complete darkness and the temperature was equilibrated at 24$\Box$ with a relative humidity of 60%. Subjects were only subjected to light stimulation when the pupil of dyes attained a minimum size of 2 mm by projecting illumination equalized with the same spectral radiance of 500-700 nm with 50-nm internal radiance. HRV was calculated from electrocardiogram (ECG) with systematic respiratory control at 0.35 Hz. The results suggest that illumination with certain wavelengths may induce ANS activation.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.3
• /
• pp.1-6
• /
• 2012

In this paper, inspection system based on optical scanning mechanism is designed and developed for solar cell wafer. It consists of optical scanning mechanism, NIR camera optics, machinery and control system, algorithm of defect detection and software. Optical scanning mechanism is composed of geometrical camera optics and structured hybrid illumination system. It is used to inspection of surface defects. NIR camera optics is used for inspection of defects inside solar cell wafer. It is shown that surface and internal micro defects can be detected in developed inspection system for solar cell wafer.