• Journal of Dental Rehabilitation and Applied Science
• /
• v.22 no.3
• /
• pp.211-220
• /
• 2006

Need of porcelain-repair system is largely demanding as dental porcelain restorations are increased in clinical dentistry. This study investigated shear bond strength of commercial porcelain-repair systems on dental porcelain and their reliability. Experimental groups were as follows; Group A Super Bond C&B, Group B Porcelain repair kit, Group C Ceramic repair, and Group D Spectrum system as a control. Porcelain disks were fired and embedded in epoxy resin. Porcelain surface were ground using 220 grit SiC disk, then cleaned in ultrasonic bath. Then porcelain specimens were treated with each repair system. A clear polystyrene cylinder 3.5 mm in internal diameter was filled with composite resin. Then the resin cylinder was polymerized with a visible light curing unit. Thirty one specimens at each group were prepared and stored at $37^{\circ}C$ distilled water for 48 h. Specimens were tested in an Instron testing machine according to ISO TR 11405. Mean shear bond strength and standard deviation of each group was $15.7{\pm}4.1MPa$ (Group A), $12.8{\pm}4.9MPa$ (Group B), $7.2{\pm}3.0MPa$ (Group C) and $9.6{\pm}2.2MPa$ (Group D). ANOVA and Tukey HSD post-hoc test showed that there were significant differences between groups (p<0.05). Data of bond strength were analyzed with two-parameter Weibull distribution. Confidence interval of Weibull modulus (m-parameter) at 95% of Group A (3.5-6.3) and Group D (3.6-6.0) were significantly higher than Group B (2.2-3.7) and Group C (2.0-3.4). There was little correlation between mean shear bond strength and Weibull modulus. Results indicated that acid-etching of porcelain surface increased porcelain-resin shear bonding strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.661-664
• /
• 2008

As architectures have recently become high-risers and megastructured, stable high strength products have been ensured. Accordingly, use of precast concrete accouplement has been increased in order to facilitate air compression and rationalize construction. Since not only external heating but also internal temperature rise caused by the accumulation of cement hydration heat in manufacturing process, precast concrete members with large cross-section used for high-rise mega-structure's columns and beams may exhibit different temperature history compared to the precast concrete members for wall and sub-floor with relatively small cross-sections. Therefore, this study aims to elucidate the characteristics of temperature history of mass concrete members cast with high-strength concrete for precast concrete application. In this study, large cross-sectional precast concrete mock-up, unit cement quantity, and temperature histories in manufacturing precast concrete member under different curing condition were inclusively investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.101-104
• /
• 1998

We report some methods for measuring a LiNbO$_3$ optical phase modulator bandwidth. Since Mach-Zehnder waveguide type, one of methods for modulation bandwidth measurement, is comparatively simple and useful, it was adapted in this work. In order to confirm this method, the waveguide of single and Mach-Zehnder type were fabricated on the same wafer. The Mach-Zehnder interferometric waveguide and the single channel waveguide were used for the measurement of the phase modulator's driving voltage and bandwidth for device fabrications, respectively. Ti-860$\AA$ in-diffusion was achieved in a wet-bubbling oxygen environment at 105$0^{\circ}C$/8hours. LINbO$_3$ internal chips were pigtailed to PMF(polarization maintaining fiber)/SMF(single mode fiber) using an epoxy curing technique. Examined were optical properties such as an insertion loss, propagation loss and mode size, and the loss mechanism of optical coupling between an optical fiber and a waveguide was considered.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.5
• /
• pp.441-448
• /
• 2020

In this study, the engineering characteristics of CLSM mixed with GBFS and GF were identified to review the applicability as a replacement material and further evaluate the recharge and field applicability as a joint filler material. This study has resulted in the following findings. First, Using more than 30% of GBFS to replace FA enabled bleeding control through improved fluidity. Moreover, it has been confirmed that effective strength and proper quality can be achieved when it was applied as a refiller and joint filler material with higher early strength than the base material. Second, When using more than 30% of FNS to replace sand, it was found that adding 0.3~0.35 of the AE agent is effective for bleeding control through improved fluidity. Third, When using more than 30% of both GBFS and FNS in combination, it was found that adding 0.3~0.35 of the AE agent is effective for bleeding control through improved fluidity. Also, it was confirmed that proper mixing of 15~60% of GF secured the effective strength and desired quality as a refiller and joint filler material. Fourth, The relationship between the superficial level and internal micro pores of CLSM from the curing process needs to be discussed and reviewed in more detail through further research studies.

• Elastomers and Composites
• /
• v.44 no.1
• /
• pp.47-54
• /
• 2009

EPDM(Ethylene-propylene-diene-terpolymer) compound reinforced with carbon black having four different particle size, acetylene black(thermal conductivity carbon black), and silica were manufactured by internal mix and open mill. To investigate the effect of particle size of filler and filler type on far-infrared vulcanization, intermal temperature of compound, degree of curing, infrared spectroscopy, and thermal analysis were measured. The thermal conductivity of far-infrared vulcanized EPDM compound increased with increasing particle size of carbon filler, but hot air vulcanized EPDM compound is not affected by particle size. The thermal conductivity was increased in the order of carbon black < silica < acetylene black(thermal conductivity carbon black).

• Mycobiology
• /
• v.43 no.3
• /
• pp.303-310
• /
• 2015

The increasing emergence of lead drugs for the resistance produced by the pathogenic strains and arrival of new diseases have initiated the need for searching novel metabolites with best anticancer and antimicrobial properties than the existing one. With this view, the investigation was conducted for the isolation, identification, and biological evaluation of potential endophytic fungi of Aegle marmelos, a medicinal tree used for more than three decades, for curing various disorders. A total of 169 endophytic fungal strains obtained from sampling and among those 67 were pigmented strains. Upon antagonistic screening, five endophytic fungal strains exhibited antagonistic potentiality by inhibiting the pathogens. These five potent strains were characterized at molecular level by sequencing the amplified internal transcribed spacer (ITS) 1 and ITS 4 regions of rDNA and they were grouped under order Pleosporales, Eurotiales, and Capnodiales. The metabolites from the respective strains were produced in fungal culturing media and extracted using polar solvents. Further, the extracts of five endophytes manifested antimicrobial activity against tested clinical pathogens and Alternaria alternata (FC39BY), Al. citrimacularis (FC8ABr), and Curvularia australiensis (FC2AP) exhibited significant antimicrobial profile against 9 of 12 tested pathogens, showing broad spectrum activity. The antioxidant levels of all the five endophytes revealed the highest activity at least concentrations, and major activity was unveiled by the members of order Pleosporales FC2AP and FC8ABr. This research explains the value of endophytic fungal extracts and its significance of antimicrobial and antioxidant properties.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.4
• /
• pp.383-389
• /
• 2015

The objective of this study is to develop mixture proportioning approach of crack controlled lightweight foamed concrete without using high-pressure steam curing processes, as an alternative to autoclaved lightweight concrete blocks (class 0.6 specified in KS). To control thermal cracks owing to hydration heat of cementitious materials, 30% ground granulated blast-furnace slag (GGBS) was used as a partial replacement of ordinary portland cement (OPC). Furthermore, polyvinyl alcohol (PVA) and polyamid (PA) fibers were added to improve the crack resistance of foamed concrete. The use of 30% GGBS reduced the peak value of hydration production rate measured from isothermal tests by 28% and the peak temperature of foamed concrete measured from semi-adiabatic hydration tests by 9%. Considering the compressive strength development, internal void structure, and flexural strength of the lightweight foamed concrete, the optimum addition amount of PVA or PA fibers could be recommended to be $0.6kg/m^3$, although PA fiber slightly preferred to PVA fiber in enhancing the flexural strength of foamed concrete.

• Elastomers and Composites
• /
• v.41 no.4
• /
• pp.245-251
• /
• 2006

Thermoplastic elastomer was prepared from dynamical vulcanization of isotactic polypropylene(iPP)/nitrile rubber blend (NBR/iPP=70/30 wt/wt) in an internal mixer using dicumyl peroxide (DCP) as a curing agent and zinc dimethacrylate (ZDMA) as a coagent. There was a great improvement in tensile and tear strength, elongation-at-break and lower tension set when ZDMA was incorporated into the blend, which is supposed to be due to the increase in crosslink density or the rubber phase and the reduction in size of the rubber particles. It was revealed that the dynamically vulcanized blend exhibited good reprocessibility, indicating its thermoplastic nature.

• International conference on construction engineering and project management
• /
• 2017.10a
• /
• pp.89-98
• /
• 2017

The floor heating method generally uses a wet construction method including the installation of resilient material, lightweight foam concrete, heating piping, and finishing mortar. Such a wet construction method not only delays other internal finishing processes during curing period for two mortar pouring process, but also has a disadvantage that it is difficult to replace the floor heating layer when it deteriorated because it is integrated with the frame. Dry floor heating construction method can be a good alternative in that it can solve these defects. Conversely, when it applied to the wall structure that is vulnerable to the interlayer noise compared with the column-beam structure, the question about the heavy-impact sound(HIS) insulation performance is raised. Therefore, conventional dry floor heating method is hard to apply to the wall structure apartments. Therefore, for the purpose to improve the applicability of dry floor heating method in wall structure apartments, this study investigated the change of floor impact sound, especially HIS insulation performance which is one of the required performance for the floor structure. This study tried to examine whether the change of heavy-impact sound pressure level(SPL) shows a tendency at the significant level according to the shape and mass of the floor structure. Through filed experiments on wall structure apartment, this study confirmed that the form of the raised floor shows better HIS insulation performance than the fully-supported form. In addition, it was also confirmed that the HIS insulation performance increases with the mass on the upper part. Moreover, this study found the fact that a mass of about 30 kg/m² or more should be placed on the upper structure to reduce the heavy-impact SPL according to the bang machine measuring method. Although this study has a limit due to insufficient experiment samples, if the accuracy of this study is increased, it will contribute to the diffusion of dry floor heating by setting the HIS insulation performance target and designing the dry floor heating structure that meets the target.

• Herbal Formula Science
• /
• v.15 no.1
• /
• pp.137-144
• /
• 2007

Background and Objectives : There are three kinds of formulas for purging the spleen to cure its sthenic syndrome based on the types of preparation formulas : Sabeetang, Sabeehwan, Sabeesan and Sabeeeum. Another formulas called Sahwangtang, Sahwangsan. Sahwangeum is to purge the yellow colour of spleen. There are 8 kinds of Sabeetang, 3 kinds of Sabeehwan, 3 kinds of Sabeesan, 1 kind of Sabeeeum, 4 kinds of Sahwangtang, 7 kinds of Sahwangsan, and 1 kind of Sahwangeum. Combination of herbal medicines, carried out in formulas for purging the spleen, consists of various kinds depending on medical scientists' personal experience in medical treatment without any general principles, which makes it difficult to apply it to clinical use. The objectives of this study lie in theoretical establishment of Sabeetang for curing the sthenic syndrome of spleen through analyzing the component medicines and combination principles of Hyeongok's Sabeetang, and furthermore, maximizing the clinical use of Sabeetang. Methods : This study analyzed the component medicines and combination principles of Hyeongok's Sabeetang based on the theory for properties and tastes of herbal medicines from the ${\ulcorner}$Yellow Emperor's Canon of Internal Medicine${\lrcorner}$ , the theory for principal herbal medicine, assistant herbal medicine, adjuvant herbal medicine, dispatcher herbal medicine, and the five elements doctrine. Hyeongok's Sabeetang is an odd prescription, composed of 7 kinds of ingredients : No.1 Rhizoma Coptidis (2don;7.5g), No.2 Fructus Gardeniae (1don;3.75g), No.3 Ramulus Cinnamomi (1don), No.4 Gypsum Fibrosum (1don), No.5 Fructus Aurantii Immaturus (1don), No.6 Cortex Magnoliae Omcinalis (1don), and No.7 Radix Et Rhizoma Rhei (1don) Results : There are three methods for curing the sthenic syndrome of spleen according to the five elements doctrine : purging the spleen, purging the lung and invigorating the liver. First, if you suffer from the sthenic syndrome of the spleen, you need to purge your spleen. There are two available methods, including taste and property purgation according to the theory for properties and tastes of herbal medicines. They each imply the bitter taste and the cool property purge the spleen. In the case of taste purgation, two herbal medicines with bitter taste. Rhizoma Coptidis and Fructus Gardeniae, are combined into the principal and assistant herbal medicine, respectively. For property purgation, three herbal medicines with the cool property, Gypsum Fibrosum, Fructus Aurantii Immaturus and Radix Et Rhizoma Rhei, are combined into adjuvant herbal medicines. Secondly, if you suffer from the sthenic syndrome of the spleen, you need to purge your lung which is child in the mother-child relationship in inter-promotion among the five elements. There are two methods to purge the lung, including taste and property purgation according to the theory for properties and tastes of herbal medicines. They each mean the pungent taste and the warm property purge the lung. Therefore, it is important to use pungent herbal medicines for taste purgation and warm ones for property purgation. Both pungent and warm herb and property invigoration to invigorate the liver with warm property. Therefore, it is important to use pungent herbal medicines for taste invigoration and warm ones for property invigoration. Both pungent and warm herbal medicines, Ramulus Cinnamomi and Cortex Magnoliae Officinalis, were combined to invigorate the liver and purge the lung. In addition, Gypsum Fibrosum are combined as dispatcher herbal medicine, leading all the herbal medicines composing the formula to the spleen. Conclusions : First, to cure the sthenic syndrome of the spleen, the methods of purging the spleen and the lung, and invigorating the liver should be used according to the five elements doctrine. Secondly, herbal medicines appropriate for those treatment methods should be chosen according to the theory for properties and tastes of herbal medicine and thirdly, the combination of those herbal medicines should be carried out according to the theory for principal herbal medicine, assistant herbal medicine, adjuvant herbal medicine, dispatcher herbal medicine. As a good example, Hyeongok's Sabeetang is combined according to the above theories. In conclusion, this formula was created by applying to the theory for properties and tastes of herbal medicines.