• 조명전기설비학회논문지
• /
• 제29권8호
• /
• pp.63-69
• /
• 2015

This paper presents the surface flashover characteristics to simulate the poor contact between an anode and a solid dielectric in a $N_2/O_2$ mixture gas (8/2) under a non-uniform field. The surface flashover voltage of the $N_2/O_2$ mixture gas revealed the irregular tendency that was not in accordance with the Paschen's law with an increasing gap of the poor contact. In addition, the insulation performance of the $N_2/O_2$ mixture gas at 0.6MPa was comparable to that of $SF_6$ gas of 0.1MPa based on the insulation performance on the poor contact. These results are able to apply the insulation design of eco-friendly gas insulation switchgear considering the internal faults.

• Journal of the Korean Wood Science and Technology
• /
• 제52권2호
• /
• pp.101-117
• /
• 2024

The conversion characteristics of the major components of Liriodendron tulipifera were investigated during acid-catalyzed organosolv pretreatment. Glucan in L. tulipifera was slowly hydrolyzed, whereas xylan was rapidly hydrolyzed. Simultaneous hydrolysis and degradation of xylan and lignin occurred; however, after complete hydrolysis of xylan at higher temperatures, lignin remained and was not completely degraded or solubilized. These conversion characteristics influence the structural properties of glucan in L. tulipifera. Critical hydrolysis of the crystalline regions in glucan occurred along with rapid hydrolysis of the amorphous regions in xylan and lignin. Breakdown of internal lignin and xylan bonds, along with solubilization of lignin, causes destruction of the lignin-carbohydrate complex. Over a temperature of 160℃, the lignin that remained was coalesced, migrated, and re-deposited on the surface of pretreated solid residue, resulting in a drastic increase in the number and content of lignin droplets. From the results, the characteristic conversions of each constituent and the changes in the structural properties in L. tulipifera effectively improved enzymatic hydrolysis in the range of 140℃-150℃. Therefore, it can be concluded that significant changes in the biomass recalcitrance of L. tulipifera occurred during organosolv pretreatment.

• 한국식품과학회지
• /
• 제37권1호
• /
• pp.44-49
• /
• 2005

쌀 전분에 propylene oxide(PO)를 단계별(전분 공형분 대비 2-12%)로 20시간과 24시간 반응시켜 하이드록시프로필화 쌀 전분을 제조하고, 변성된 쌀 전분의 용해도, 팽윤력, RVA, DSC 특성을 연구하였다. 팽윤력은 일반 쌀 전분 보다 낮은 온도에서 증가되기 시작하였으나 높은 경향을 보였으며, 하이드록시프로필화 쌀 전분이 일반 쌀 전분보다 완만한 상승을 나타내었다. 용해도는 하이드록시프로필화 쌀 전분이 일반 쌀 전분보다 낮은 결과를 나타내었고 PO 함량이 높을수록 높아지는 결과를 보였다. RVA 분석결과 PO 함량이 높을수록 pasting temperature와 peak time이 낮아졌고 최고 점도는 하이드록시프로필화 쌀 전분이 일반 쌀 전분보다 낮고 holding strength는 높은 경향을 나타내고 breakdown의 경우 반응시간이 24시간이 20시간보다 낮은 경향을 보였으며 Setback은 24시간 반응시킨 처리구들이 일반 쌀 전분보다 낮은 것으로 나타났다. DSC분석결과 PO 함량이 높을수록 To, Tp, Tc, ${\Dalta}H$가 감소하였다. 따라서 하이드록시프로필화 쌀 전분의 경우 전분입자내의 intemal bond가 하이드록시프로필기에 의해 약해져서 호화가 쉽게, 즉 낮은 온도에서 일어나는 것으로 판단되었고 최대 팽윤력, breakdown에서 옥수수 전분과는 다른 결과를 나타내어 전분의 종류에 따라 같은 변성 처리라고 하더라도 다른 결과를 나타낼 수 있다는 사실이 확인되었다.

• 한국안전학회지
• /
• 제28권2호
• /
• pp.26-30
• /
• 2013

The purpose of this study is to find risk factors by analyzing the operation principle of a photo coupler (P/C) used to remove the noise of electronic devices and establish a base for the performance improvement of developed products. It was found from the P/C circuit analysis of normal products that they were equipped with an electrolytic condenser of $0.1{\mu}F$ to smooth system signals. Due to the epoxy resin packing the external part of the P/C, this study experienced a limit to visually examine the damage to it. It could be seen from the analysis of electric characteristics of the P/C that the forward voltage ($V_f$) and reverse current ($I_r$) were 1.3 V and 10 uA, respectively. In addition, it is required that the breakdown voltage (VCE) between the collector (C) and emitter (E) be maintained at less than 35 V. The and of the damaged product #1 were comparatively good. However, the measurement of was 100.0 uA. From this, it is thought that a short circuit occurred to the internal circuit. Moreover, from the fact that the of the damaged product #2 was open circuit and the measurement of was 0.0 uA, it is thought that the collector and emitter was separated or insulation resistance was significantly high. Furthermore, from the fact that the of the damaged product #3 was open circuit and the measurement of was 0.0 uA, it is thought that the space between the collector (C) and emitter (E) failed to meet the design standard or that they were separated. Therefore, it is thought that fabricating the P/C by increasing the reverse current 10 mA to 50 mA will prevent its malfunction.

• 한국전기전자재료학회논문지
• /
• 제20권1호
• /
• pp.57-64
• /
• 2007

One of the cause of insulation failure in power cable is well known by electrical treeing discharge. This is occurred for imposed continuous stress at cable. And this event is related to safety, reliability and maintenance. In this paper, throughout analysis of partial discharge(PD) distribution when occurring the electrical tree, is studied for the purpose of knowing of electrical treeing discharge characteristics according to defects. Own characteristic of tree will be differently processed in each defect and this reason is the first purpose of this paper. To acquire PD data, three defective tree models were made. And their own data is shown by the phase-resolved partial discharge method (PRPD). As a result of PRPD, tree discharge sources have their own characteristics. And if other defects (void, metal particle) exist internal power cable then their characteristics are shown very different. This result Is related to the time of breakdown and this is importance of cable diagnosis. And classification method of PD sources was studied in this paper. It needs select the most useful method to apply PD data classification one of the proposed method. To meet the requirement, we select methods of different type. That is, neural network(NN-BP), adaptive neuro-fuzzy inference system and PCA-LDA were applied to result. As a result of, ANFIS shows the highest rate which value is 98 %. Generally, PCA-LDA and ANFIS are better than BP. Finally, we performed classification of tree progress using ANFIS and that result is 92 %.

• 비파괴검사학회지
• /
• 제14권1호
• /
• pp.16-22
• /
• 1994

일반적으로 구름 베어링 시스템에 비해 발전용 터어빈이나 내연기관 엔진과 같은 저어널 베어링을 가진 시스템은 상대적으로 대형 설비이거나 더 가혹한 운전조건에서 가동되는 경우가 많다. 이런 회전기계류에서의 베어링의 파손은 설비의 운전 중단 및 관련 설비의 파손까지도 초래할 수 있게 된다. 따라서 이로 인한 보수에 소비되는 시간 및 경제적인 손실등을 피하기 위해서는 저어널 베어링의 조기파손 감지의,역할은 매우 중요하게 된다. 본 연구에서는 음향방출 기술을 이용하여 베어링에서 발생할 수 있는 파손의 조기검출을 위해 실험실용으로 직접 제작한 저어널 베어링 시스템을 이용하여 여러 형태의 비정상 조건을 만들어 가며 실험을 행하였다. 베어링 손상 및 피로의 주 요인으로서는 윤활유 부족, 윤활층에의 이물질의 혼입, 조립 불량 등이 대표적인 원인으로서 알려져 있으며 이에 근거하여 실험 조건을 윤활유에의 이물질 혼입, 윤활유 부족, 그리고 축과 베어링간의 금속간 접촉등의 인위적인 형태로 구성하여 실험하였다. 그 결과로서 음향방출 기술이 저어널 베어링의 조기파손 감지에 매우 효과적인 도구라는 것을 입증하였다.

• 전기학회논문지
• /
• 제60권8호
• /
• pp.1560-1565
• /
• 2011

The environmental pollution caused by green-house gases such as $CO_2$ and $SF_6$ has been becoming the main issue of industrial society. Many developed countries are making efforts to minimize the amount of $CO_2$ emission come from the operation of high voltage electrical apparatuses. As a part of these efforts, 180 countries signed the Kyoto Protocol in 1997 to cut back on their green-house gas emissions. Nowadays, the study on the development of dry air insulated switchgear (DAIS) which is known as an eco-friendly electrical apparatus is in progress. A DAIS is advantageous for minimizing the effect of impurities and enhancing the dielectric characteristics over an air insulated switchgear (AIS) by applying constant pressure to an enclosed cubicle. Therefore, a study on the electrical insulation performance of dry air as a gaseous insulation medium is conducted in this paper to substitute a gas insulated switchgear (GIS) for DAIS. As results, it is verified that the AC dielectric characteristics of dry air are similar to those of air and the lightning impulse dielectric characteristics of dry air are superior to those of air at 1bar pressure condition. However, dry air is of inferior dielectric characteristics to $SF_6$ at 4bar pressure condition. Finally, it is suggested that the internal pressure of DAIS should be over 4bar pressure to develop a high voltage switchgear which has similar electrical performance to a conventional GIS. Also, the empirical formulae on calculating the maximum electric field intensity at sparkover of dry air are deduced by experiments according to pressures. It is expected that these results are helpful to design and develop a high voltage electrical apparatus.

• 한국안전학회지
• /
• 제33권2호
• /
• pp.21-27
• /
• 2018

The expansion and stable operation of electric power facilities are important factors with development of industrial facilities in modern society. In high-voltage equipment such as GIS, the insulation characteristics may be deterioated by environment-friendly gas adaption and miniaturization. There is also the possibility of accidents due to insulation breakdown due to the deterioration of power facilities. Therefore, it is necessary to extend the diagnosis system to continuously monitor the danger signals of these power equipment and to prevent accidents. Most of the internal defects in the GIS system are conductive particles, floating electrode defects, protrusion defects, and the like. In this case, a partial discharge phenomenon is accompanied. These partial discharge signals occur irregularly and various noise signals are included in the field, so it is difficult to evaluate the reliability in the development of the diagnostic system. In this paper, a study was made on equipment capable of generating a partial discharge simulated signal that can be adjusted in size and frequency to be applied to a diagnostic device by electromagnetic wave detection method. The PD simulated pulse generator consists of a user interface module, a high-voltage charging module, a pulse forming circuit, a voltage sensor and an embedded controller. In order to simulate the partial discharge phenomenon similar to the actual GIS, a discharge cell was designed and fabricated. The application of the prototype pulse generator to the commercialized PD diagnosis module confirmed that it can be used to evaluate the performance of the diagnostic device. It can be used for the development of GIS diagnosis system and performance verification for reliability evaluation.

• 한국식품과학회지
• /
• 제20권5호
• /
• pp.650-658
• /
• 1988

발아 중인 대두와 두채 자엽부에서의 단백지 유동 현상을 광학현미경(LM)과 주사 전자현미경(TEM)을 이용하여 epidermis, vascular tissue 그리고 storage parenchyma에서 비교 관찰하였다. 발아 초기의 자엽에는 직경이 $0.1-15{\mu}m$에 해당하는 다양한 크기의 단백질 체(protein bodies)로 채워져 있었으며 epidermis와 vascular tissue의 단백질체는 parenchyma 세포보다 훨씬 적은 크기의 $0.1-5{\mu}m$였다. 발아가 진행됨에 따라, 단백질의 분해현상은 epidermis와 vascular tissue에서 먼저 시작되었다. 그 분해 유형은 먼저 침투한 수분에 의해 팽창된 단백질체의 외막에는 손상이 없어 단백질 체 내부와 외부로부터 가수분해가 일어났으며, 단백질이 완전히 분해도기 전에 단백질체 끼리의 융합 또한 관찰 되어졌다. 단백질체 분해의 결과는 세포내에 중심액포를 만든다는 것이며, 두채 성장 말기에는 액포막의 파괴현상도 관찰되었다.

• ETRI Journal
• /
• 제26권4호
• /
• pp.315-320
• /
• 2004

This paper proposes a 10-${\mu}m$ thick oxide layer structure that can be used as a substrate for RF circuits. The structure has been fabricated using an anodic reaction and complex oxidation, which is a combined process of low-temperature thermal oxidation (500 $^{\circ}C$ for 1 hr at $H_2O/O_2$) and a rapid thermal oxidation (RTO) process (1050 ${\circ}C$, for 1 min). The electrical characteristics of the oxidized porous silicon layer (OPSL) were almost the same as those of standard thermal silicon dioxide. The leakage current density through the OPSL of 10 ${\mu}m$ was about 10 to 50 $nA/cm^2$ in the range of 0 to 50 V. The average value of the breakdown field was about 3.9 MV/cm. From the X-ray photo-electron spectroscopy (XPS) analysis, surface and internal oxide films of OPSL prepared by a complex process were confirmed to be completely oxidized. The role of the RTO process was also important for the densification of the porous silicon layer (PSL) oxidized at a lower temperature. The measured working frequency of the coplanar waveguide (CPW) type short stub on an OPSL prepared by the complex oxidation process was 27.5 GHz, and the return loss was 4.2 dB, similar to that of the CPW-type short stub on an OPSL prepared at a temperature of 1050 $^{\circ}C$ (1 hr at $H_2O/O_2$). Also, the measured working frequency of the CPW-type open stub on an OPSL prepared by the complex oxidation process was 30.5 GHz, and the return was 15 dB at midband, similar to that of the CPW-type open stub on an OPSL prepared at a temperature of $1050^{\circ}C$ (1 hr at $H_2O/O_2$).