• Journal of Environmental Health Sciences
• /
• v.30 no.2
• /
• pp.167-172
• /
• 2004

In this study, we carried out the research for the recycling potential of the dyeing wastewater treatment sludges as construction materials. The incineration ash of sludges were solidified as interlocking block in condition of sludge/cement ratio 2.5%, 5.0% and 10%, respectively. Those interlocking blocks were cured for 3days, 7days and 28days in ambient air condition, respectively. The results of this research were summarized as follows: The dyeing wastewater treatment sludges was below the Korea Leaching Limit. After incineration, the ash was manufactured as interlocking block. Bendable strength over 50kg$_{f}$/$\textrm{cm}^2$ suitable for interlocking block was obtained only when the sample was cured for 7days at sludge/cement ratio 2.5% and 5.0%. Hygroscopic ratio of interlocking block was above the Korea Industry Standard. We think that recycling of the incineration ash from dyeing wastewater treatment sludges to interlocking block will have high potential possibility.y.

• International Journal of Highway Engineering
• /
• v.16 no.2
• /
• pp.1-9
• /
• 2014

PURPOSES : This study aims to evaluate the performance of interlocking block pavement system for low speed highway. METHODS : Through on-site monitoring, environmental impact assessment of interlocking block pavement such as heat island reduction, traffic safety, noise pollution were evaluated as compared with asphalt pavement. Also the pavement condition and roughness were evaluated according to performance period. RESULTS : Surface temperature of interlocking block pavement was about 7 degree lower than asphalt pavement in midsummer. Compared to asphalt pavement, vehicle speed reduction effect of interlocking block pavement was about 2kph. For low speed driving, the noise pollution was measured at a similar level for both asphalt and interlocking block pavement. After 42month service period, the breakage of block was only 0.24% for the whole surveyed area. IRI of interlock block pavement was estimated within the range of 5~8m/km. CONCLUSIONS : Depending on the performance monitoring results such as heat island reduction, providing traffic safety and keeping a good pavement condition for a long service period, it assures that interlocking block pavement was applicable for low speed road.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.25-26
• /
• 2020

During the molding process of the existing interlocking block, the pigment is firstly laid, and cement is poured on the pigment secondly to give vibration. Interlocking blocks made of conventional cement are entirely dark where the pigment area is removed. On the other hand, when looking at the mortar with oyster shells added, the color is closer to that of the existing cement mortar. Therefore, if an interlocking block is produced by adding a pigment to a mortar with an oyster shell added, it is considered that the amount of pigment is less than that of the existing interlocking block. This study is a basic study of interlocking blocks. To investigate the strength characteristics of mortar using oyster shell powder as aggregate, W/C is 25%, 50%, oyster shell replacement rate is 0%, 25%, 50%, 75%, 100% was substituted to make a mortar and its strength change was studied.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.115-124
• /
• 2008

This Study was investigated in main breakage types of 50 interlocking block pavements in apartment houses and evaluated on their performance. According to performance evaluation, maintenance control index of 9 aged interlocking block pavements ranged 7.9 to 8.9. These values meant that the condition of interlocking block pavements were still good. Therefore, it was concluded that the 10-year cycle of the block replacement recommended by Ministry of Construction & Transportation is necessary to reappraise. To objectively evaluate the performance of interlocking block pavements, this study presented the criteria of maintenance control by combining two maintenance control standards suggested by Ministry of Construction & Transportation and the Japan Interlocking Block Pavement Engineering Association. Also, this study suggested that the domestic standard is necessary to include durability standards and quality standards of joint filling materials and bedding sand layer for increasing expectation life and reducing maintenance costs of interlocking block pavements.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.203-206
• /
• 1997

In this paper, the properties of Interlocking block contained blast furnace slag cement are compared with that with O.P.C.(ordinary portland cement) and are analyzed under various mix proportions and the dosage of AE agent. According to the experimental results, compressive strength and flexural strength of interlocking block with blast furnace slag cement are lower than that with OPC. Also the strength and the ratio of absorption decrease with higher dosage of AE agent. although interlocking block with OPC has better performance than that of blast furnace slag in the side of quality, it is worth while to use the blast furnace slag as materials of interlocking block considered the side of recycling of resources and economy.

• International Journal of Highway Engineering
• /
• v.14 no.5
• /
• pp.67-74
• /
• 2012

PURPOSES: In this study the influence factors related to abrasion resistance of interlocking concrete block have been evaluated, and comparisons between various domestic and foreign abrasion test methods was also accomplished. METHODS: The modified rotational cutting method suggested in ASTM C 944 was applied. Surface materials with different types of fine aggregate such as crushed sand, sea sand, and mixture of crushed and sea sand were tested to compare the aggregate effect for abrasion resistance. RESULTS: The different surface mixtures with various W/C ratios, mortar and fly ash ratios have been investigated for functional and economical considerations. CONCLUSIONS: This study had obtained reliable results by changing diamond blade of rotating cutter. Therefore, in order to improve the abrasion resistance of interlocking concrete block for road, a new mix design was proposed.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.23 no.3
• /
• pp.91-104
• /
• 2020

This study was conducted to analyze the characteristics of defects according to the type of block and spatial type by quantitatively examining defects occurring in block pavement in apartment complex. According to the research results, depending on the type of block, defects have occurred 1,394.3ea/100㎡ in interlocking paver blocks, 464.8ea/100㎡ in clay brick paver blocks, and 235.1ea/100㎡ in shot blasted paver blocks. By space type, the defects were occurred 1,576.0ea/100㎡ on the access road paved by interlocking paver blocks and the defects were found 1,139.6ea/100㎡ in interlocking paver blocks, 235.1ea/100㎡ in shot blasted paver blocks, and 797.1ea/100㎡ in clay brick paver blocks, on the sidewalk. Also the defects are occurred 455.6ea/100㎡ on the resting space and 403.2ea/100㎡ on the gym space paved by clay brick paver blocks. Through the size analysis of the defects in the block paver, in the case 'peeling', the largest volume of 2,539.0㎣ on the sidewalk paved with shot blasted paver blocks, and 'Subsidence' occurred at the widest area of 2,096.0㎠ on the sidewalk where interlocking paver block was constructed. The difference in defect occurrence according to the type of block is considered to be influenced by the block production process, and the space type is considered to be caused the difference in the occurrence of defects according to the cause of construction and the usage pattern of residents. This study conducted a survey on defects in block and analyzed the defect characteristic according to paver material and space type. Base on this, it is judged that it can be used as an efficient basic data for material replacement, improvement, paver planning and construction in the future.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.255-261
• /
• 2007

In this paper we introduce the method, procedure and result of RAM prediction for interlocking system which is applied for AREX signaling system. For RAM prediction, we breakdown the interlocking system to the LRU level and select the LRUs of which failure can cause the service delay. The prediction of reliability is based on the Reliability Block Diagram which is the functional diagram composed of selected LRUs and finally, the availability of interlocking system is estimated from the combination of reliability and maintainability.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.327-332
• /
• 2003

The incinerated municipal waste can be classified into two general types of ash; fly ash and bottom ash. The fly ash is appointed as specified waste, because it contains harmful heavy metals, ie Pb , Cd, etc. more than permitted standard index. The purpose of this study is to manufacture the non-sintering artificial aggregates using municipal waste incineration fly-ash and to evaluate their applications as coarse aggregates in concrete interlocking block. The test results of water absorpsion, strengths of the concrete block using artificial aggregates showed that the artificial aggregates could be used in part of 10-20% as coarse aggregate in concrete block.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.33 no.3
• /
• pp.131-138
• /
• 2021

The armor blocks are used to protect the body of the structure and dissipate wave energies, so it is crucial to evaluate the stability of the armor unit. The stability of armor blocks has been mainly evaluated through empirical coefficients called the stability coefficient obtained from hydraulic model experiments. In this study, a new type of single-layered armor block called K-Block was proposed, and a new experimental method based on the pull-out force was proposed to evaluate the stability of the armor unit, including the interlocking effects. The pull-out force test proposed in this study directly measures the force required to separate the armor unit from the armored layer on the slope by applying a tensile force in the vertical and horizontal directions to the installed armor unit. The proposed experimental method confirmed that the interlocking effects of the armor block could be quantitatively evaluated, and the high stability of the K-Block was verified.