• 대한기계학회논문집A
• /
• 제30권8호
• /
• pp.931-940
• /
• 2006

Defect assessment of a weld zone is important in fitness-for-service evaluation of plant components. Typically a J and $C^*$ estimation method for a defective homogeneous component is extended to a mismatched component, by incorporating the effect due to the strength mismatch between the weld metal and the base material. The key element is a mismatch limit load. For instance, the R6/R5 procedure employs an equivalent material concept, defined by a mismatch limit load. A premise is that if a proper mismatch limit load solution is available, the same concept can be used for any defect location (either a weld centre defect or a heat affected zone (HAZ) defect) and for any material combination (either two-material or multi-material combinations; either similar or dissimilar joints). However, validation is still limited, and thus a more systematic investigation is needed to generalise the suggestion to any geometry, any defect location and any material combination. This paper describes the effect of structural geometry on the $C^*$ integral for defective similar welds, based on systematic elastic-creep 2-D and 3-D finite element (FE) analyses, to attempt to elucidate the questions given above. It is found that the existing 'equivalent material' concept is valid only for limited cases, although it provides conservative estimates of $C^*$ for most of cases. A modification to the existing equivalent material concept is suggested to improve accuracy.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2139-2157
• /
• 1994

In order to understand the delamination between leadframe and epoxy molding compound in an electronic packaging of surface mounting type, the stress intensity factor, T-stress and J-integral in fracture mechanics are obtained. The effects of geometry, material properties and molding process temperature on the delamination are investigated taking into account the temperature dependence of the material properties, which simulates as more realistic condition. As the crack length increases the J-integral increases, which suggest that the crack propagates if it starts growing from the small size. The effects of the material properties and molding process temperature on stress intensity factor, T-stress is and J-integral are less significant than the chip size for the practical cases considered here. The T-stress is negative in all eases, which is in agreement with observation that interfacial crack is not kinked until the crack approaches the edge of the leadframe.

• Structural Engineering and Mechanics
• /
• 제72권2호
• /
• pp.229-244
• /
• 2019

Weak form integral equations are developed to investigate the flapwise bending vibration of the rotating beams. Rayleigh and Eringen nonlocal elasticity theories are used to investigate the rotatory inertia and Size-dependency effects on the flapwise bending vibration of the rotating cantilever beams, respectively. Through repetitive integrations, the governing partial differential equations are converted into weak form integral equations. The novelty of the presented approach is the approximation of the mode shape function by a power series which converts the equations into solvable one. Substitution of the power series into weak form integral equations results in a system of linear algebraic equations. The natural frequencies are determined by calculation of the non-trivial solution for resulting system of equations. Accuracy of the proposed method is verified through several numerical examples, in which the influence of the geometry properties, rotatory inertia, rotational speed, taper ratio and size-dependency are investigated on the natural frequencies of the rotating beam. Application of the weak form integral equations has made the solution simpler and shorter in the mathematical process. Presented relations can be used to obtain a close-form solution for quick calculation of the first five natural frequencies of the beams with flapwise vibration and non-local effects. The analysis results are compared with those obtained from other available published references.

• 한국수학사학회지
• /
• 제18권2호
• /
• pp.31-42
• /
• 2005

르네상스 시대가 도래하자 고대 그리스와 로마 문화의 부흥으로 유클리드 기하학이 다시 연구되고 실험과 관찰의 정신이 대두되었다. 이는 곧 근대의 정신인 것이다. 본 논문에서는 17, 18세기에 지식인이 추구했던 가치가 운동, 속도, 빛이었으므로 수학에서 미분적분차이 발명되고, 미술에서는 빛의 화가, 순간의 화가를 탄생시킨 근대의 시대정신과 사회적인 배경을 주목한다.

• Journal of Mechanical Science and Technology
• /
• 제18권9호
• /
• pp.1500-1511
• /
• 2004

In this paper, the anti-plane transient response of a central crack normal to the interface between a piezoelectric ceramics and two same elastic materials is considered. The assumed crack surfaces are permeable. By virtue of integral transform methods, the electro elastic mixed boundary problems are formulated as two set of dual integral equations, which, in turn, are reduced to a Fredholm integral equation of the second kind in the Laplace transform domain. Time domain solutions are obtained by inverting Laplace domain solutions using a numerical scheme. Numerical values on the quasi-static stress intensity factor and the dynamic energy release rate are presented to show the dependences upon the geometry, material combination, electromechanical coupling coefficient and electric field.

• The Journal of the Acoustical Society of Korea
• /
• 제28권2E호
• /
• pp.51-59
• /
• 2009

Mutual radiation impedance becomes more important in the design and analysis of acoustic transducers for higher power, better beam pattern, and wider bandwidth at low frequency sonar systems. This review paper focused on literature survey about the researches of mutual radiation impedance in the acoustic transducer arrays over 60 years. The papers of mutual radiation impedance were summarized in terms of transducer array structures on various baffle geometries such as planar, cylindrical, spherical, conformal, spheroidal, and elliptic cylindrical arrays. Then the computation schemes of solving conventional quadruple integral in the definition of mutual radiation impedance were surveyed including spatial convolution method, which reduces the quadruple integral to a double integral for efficient computation.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.304-308
• /
• 2000

In this work, an equation of J-integral for a penny-shaped crack at the end of the cord embedded in rubber matrix is proposed. The dimensional analysis is applied to derived to the equation of J-integral. We assume that the energy Parameter J is separated into the deformation and the geometry function, and which is proved using by separation parameter.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3551-3566
• /
• 2022

The STELLA program was launched to support the PGSFR development in 2012 and for the 2nd stage, the STELLA-2 facility was designed to investigate the integral effect of safety systems including the comprehensive interaction among PHTS, IHTS and DHRS. In STELLA-2, the long-term transient behavior after accidents can be observed and the overall safety aspect can also be evaluated. In this paper, the basic design concept from engineering basis to specific design is described. The design was aimed to meet similarity criteria and requirements based on various non-dimensional numbers and the result satisfied the key features to explain the reasoning of safety evaluation. The result of this study was used to construct the facility and the experiment is on-going. In general, the final design meets the similarity criteria of the multidimensional physics inside the reactor pool. And also, for the conservation of natural circulation phenomena, the design meets the similarity requirements of geometry and thermo-dynamic behavior.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1852-1860
• /
• 1991

본 연구에서는 연구대상을 주어진 구조물 형상에서 경계조건의 변화에 따른 현상 설계민감도, 특히 하중경계조건의 변화에 따른 구조물의 변형에 주안점을 두었다. 이 연구결과는 가공물의 지지위치에 따른 가공면의 변형정도 향상 및 접촉문제 해석등 에 응용이 가능하다. 유도된 민감도가 정확함을 입증하기 위하여 예제로서 하중경계 조건의 변화에 따른 범함수로 정의된 변형의 변화량을 예측하는 문제를 선정하였다.

• Nuclear Engineering and Technology
• /
• 제24권3호
• /
• pp.319-328
• /
• 1992

일차원 구에서 유한요소법의 Galerkin formulation이 일차형태의 단일 에너지 중성자 수송방정식의 적분법에 적용되었다. 구분적으로 1차 혹은 2차인 Lagrange 다항식들이 선형대수 방정식들의 집합을 만들기 위해 적분법에 있는 각의존 중성자속(angular flux)에 대하여 활용되었다. 수치해석이 균질구에서의 임계문제와 비균질구에서의 scalar flux 분포에 대해서 행해졌다. 공간과 각에 대하여 연속적인 유한요소를 사용한 균질구에서의 임계문제에 대한 유한요소법의 결과들은 이론적인 해들자 비교되었다. 비균질 문제에서는 각자 공간에 대하여 불연속 유한요소를 사용하여 구한 scalar flux 분포는 ANISN code에 의한 계산결과와 잘 일치하였다.