• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.542-547
• /
• 2013

In this study, mechanical property on the composite material of aluminum foam core is investigated by simulation analysis. Impact energies such as 50J, 70J, and 100J are applied to the specimen model. The maximum load occurs at 3.4ms for 50J, 3.2ms for 70J, and 3.2ms for 100J respectively. The striker penetrates the upper face sheet, causing the core to be damaged at 50J test but the lower face sheet remains intact with no damage. It results in occurring with the energy of 52 J. At 70J test, it penetrates the upper face sheet and penetrated the core. And the striker causes the lower face sheet with damage. And it results in occurring with the energy of 65 J. Finally at 100J test, the striker penetrated both the upper face sheet and core and even the lower face sheet. The load becomes maximum at the time when striker penetrates through the upper plate and it rapidly reduced. And then the load increases rapidly when reaching the lower face sheet. And it decreases again. It results in occurring with the energy of 95 J.

• Korean Journal of Plant Resources
• /
• v.33 no.4
• /
• pp.293-302
• /
• 2020

Morphological characteristics of Ziziphus jujuba accessions, including 'Ilbon', were investigated to verify the possibility of 'Ilbon' as a breeding material. 'Ilbon' has smaller leaves and fruits and a lower total soluble solids content compared to the major Z. jujuba accessions. However, total polyphenol content and antioxidant capacity were highest in 'Ilbon' among the Z. jujuba accessions. In addition, 'Ilbon' could produce intact seeds and seed productivity of 'Ilbon' was highest compared with major Z. jujuba accessions. Principal component analysis and clustering analysis using the morphological characteristics of Z. jujuba accessions have been classified them to geographical origin. In particular, 'Ilbon' was clearly distinguished from the major Z. jujuba accessions. Therefore, 'Ilbon', which has the highest seed productivity and functional component, will be used as a material for cross breeding and will promote genetic study of Z. jujuba.

• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.451-458
• /
• 2002

Osteoporosis is a systemic skeletal disease caused by low bone mass and the decrease of bone density in the microstructure of trabecular bone. Drug therapy(PTH Parathyroid hormone) may increase the trabecular thickness and thus bone strength. Vertebroplasty is a minimally invasive surgery foy the treatment of osteoporotic vertebral compression fracture. This Procedure includes Puncturing vertebrae and filling with Polymethylmethacrylate(PMMA). Although altering recommended monomer-to-Powder ratio affects material properties of bone cement, clinicians commonly alter the mixture ratio to decrease viscosity and increase the working time. The Purposes of this study were to analyze the effect of 4he monomer-to-powder ratio on the mechanical characteristics of trabecular. In this paper, the finite element model of human vertebral trabecualr bone was developed by modified Voronoi diagram, to analyze the relative effect of hormone therapy and vertebroplasty at the treatment of osteoporotic vertebrae. Trabeuclar bone models for vertebroplasty with varied monomer-to-Powder ratio(0.40∼1.07 ㎖/g) were analyzed. Effective modulus and strength of bone cement-treated models were approximately 60% of those of intact models and these are almost twice the values of hormone-treated models. The bone cement models with the ratio of 0.53㎖/g have the maximum modulus and strength. For the ratio of 1.07㎖/g, the modulus and strength were minimum(42% and 49% respectively) but these were greater than those for drug therapy. This study shows that bone cement treatment is more effective than drug therapy. It is found that in vertebroplasty, using a monomer-to-powder ratio different from that recommended by manufacturer nay significantly not only reduce the cement's material Properties but also deteriorate the mechanical characteristics of osteoporotic vertebrae.

• Journal of Food Hygiene and Safety
• /
• v.22 no.2
• /
• pp.110-115
• /
• 2007

This test was performed to evaluate the skin irritation and sensitization of Creocomplex, disinfectant, Containing 10% 4-chloro-m-cresol, 10% didecyl dimethyl ammonium chloride, and 10% glutaraldehyde. In primary skin irritation test, rabbits were dermally treated with Creocomplex for 24 hrs. The disinfectant did not induce any adverse reactions such as erythema and edema on intact skin sites, but on abraded skin sites, some rabbits showed very slight erythema and edema 24hr after topical application. So, the disinfectant was classified as a practically non-irrifating material based on the score 0.13 of primary irritation index. In the skin sensitization test, guinea pigs were sensitized with intradermal injection of 0.1ml Creocomplex for 24 hr. After 1 week, Creocomplex was treated on the site of injection, and challenged 2 weeks later. Creocomplex did not induce any allergic reactions. Therefore, 10% Creocomplex was graded as a weak material from 0 in both sensitization score· and rate. From results of the present study, it is suggested that 10% Creocomplex does not cause contact irritation and sensitization.

• Journal of Food Hygiene and Safety
• /
• v.36 no.1
• /
• pp.17-23
• /
• 2021

This evaluation tested the skin irritation and sensitization of an acaricide (Wagoojabi II®, WGJB) for the control of poultry red mite, containing 20% Chamaecyparis obtusa oil and 56% Cinnamomum camphora oil. In a primary skin irritation test, rabbits were dermally treated with WGJB for 24 h. The acaricide did not induce any adverse reactions such as erythema and edema on intact skin sites, but on abraded skin sites, some rabbits showed very slight erythema and edema 24 h after topical application. So, the acaricide was classified as a practically mild-irritating material based on a 0.625 primary irritation index score. In the skin sensitization test, guinea pigs were sensitized with intradermal injection of 0.1mL WGJB for 24 h. After 1 week, The WGJB was treated on the site of injection, and challenged 2 weeks later. The WGJB did not induce any allergic reactions. Therefore, the WGJB was graded as a weak material at '0' in both sensitization score and rate. From the results of this study, it is suggested that WGJB does not cause contact irritation and sensitization.

• Korean Journal of Weed Science
• /
• v.14 no.2
• /
• pp.120-127
• /
• 1994

To establish an efficient herbicide screening method for purple nutsedge(Cyperus rotundus) control, its sprouting characteristics, tuber production and responses on several herbicides were investigated under greenhouse condition. The tubers stored at $4^{\circ}C$ after sterilization with the diluted prochloraz(Spotac) solution showed higher sprouting than the non-sterilized did. The harvested tubers were not dormant, and the sterilized tubers which stored at low temperature had a sprouting capability of about 80% after 6 months. If the fresh weight of purple nutsedge tubers was decreased to below 48%, they could not sprout. However, the tubers soaked in water and then stored at low temperature could sprout by 88% even 6 months later. Sprouting and initial growth of tuber were much better at $35^{\circ}C$-day/$25^{\circ}C$-night than at 30/$20^{\circ}C$ or 25/$15^{\circ}C$. The half-sected tubers, which were prepared by setting the intact tuber of above 1.2g latitudinally, were shown similar initial growth to the intact but those sected crucifically were not. These results suggest that the half-sected tuber itself can be used as a material on herbicide screening. About 1000 tubers could be harvested when 10 tubers planted in a pot($56{\times}35{\times}16cm$) filled with the artificial soil were cultivated in greenhouse of $35^{\circ}C$-day/$25^{\circ}C$-night for 3 months(April-July, 1993). Chlorimuron, Bentazon and Norflurazon were selected as the standards for the screening because of providing relatively effective control on purple nutsedge in both soil-surface and foliar spray treatment.

• Journal of Chest Surgery
• /
• v.31 no.9
• /
• pp.884-892
• /
• 1998

Background: The gastroepiploic artery is not only an alternative graft but also may be considered an important primary graft for coronary revascularization. However, the long-term patency of the gastroepiploic arterial graft is yet to be determined and the incidence of perioperative spasm and long-term patency of a coronary graft may be affected by the properties of the graft response to certain vasoactive substances. The reactivity of the gastroepiploic artery to vasoactive substances has not been studied extensively and the results of the studies are contradictory. Material and Method: This study was designed to test the reactivity of human gastroepiploic artery to four constrictors and four relaxants. The middle sections of the human gastroepiploic arteries were collected from the patients undergoing gastrectomy and the arterial rings with intact endothelium were suspended in organ baths for isometric tension recording. Result: Epinephrine, norepinephrine, and potassium chloride induced the maximum constriction to higher forces (7.0$\pm$1.1g, 6.6$\pm$0.9g, and 6.5$\pm$1.1g) than 5-hydroxytryptamine did (3.8$\pm$1.7g, p<0.05). Nitroprusside and histamine induced almost full relaxation in the gastroepiploic arteries preconstricted with norepinephrine. There was no significant difference between two relaxants regarding maximum relaxation force. Acetylcholine induced the maximum relaxation to weaker force when compared with nitroprusside and histamine (p<0.05), and isoproterenol was the weakest of the relaxants (p<0.05 compared with acetylcholine). Conclusion: The gastroepiploic artery has a strong capacity of endothelium-dependent relaxation which could have an important influence on long-term patency. The gastroepiploic artery exhibits a potent contractility to catecholamines and the enhanced contractility may facilitate vasospasm in the presence of high circulating levels of catecholamines. Nitroprusside, a potent relaxant in gastroepiploic artery, might be beneficial for the treatment of gastroepiploic arterial graft spasm. The gastroepiploic arterial graft with intact endothelium may respond weakly to beta-adrenoceptor agonist and 5-hydroxytryptamine.

• Applied Microscopy
• /
• v.39 no.2
• /
• pp.167-173
• /
• 2009

Capillaria hepatica is a parasitic nematode which causes hepatic capillariasis in rodents and other mammals, including man. Rat species of the genus Rattus are main primary host and rates of genus Rattus of up to 100% have been reported. Infection to reservoir and other mammalian hosts occur incidentally due to ingestion of water or food contaminated with C. hepatica embryonated eggs. The worms mature exclusively inside the liver, but they die and disassemble soon after egg spawning in rats. Dead worms and their eggs cause immune response of focal necrosis and inflammation within the liver. C. hepatica adult with a thin and long body is similar to capillary. The members of Order Trichurida are characterized by having a stichosome and the bacillary bands in front of the body. As already mentioned, the adult C. hepatica residesin the liver, where it deposits groups of eggs, and finally die in the encapsulated tissue of the liver. They produce eggs that elicit a marked granulomatous reaction that eventually destroy the worms. And the adult worms were mixed with eggs. So the complete isolation of the worm and observation of intact ultrastructure is very difficult. In this study, integument structure of C. hepatica isolated from the liver of mouse at 7 weeks after inoculation of embryonated eggs were observed with scanning and transmission electron microscopy. As a results, body length of isolated C. hepatica was about 99 mm. Cuticle, bacillary band and bacillary pore were obtained in the integument of worm. Bacillary pore across cuticular surface of the worm were observed. According to the existence of cap material, external forms of bacillary pore can be divided into three types such as flat, ingression, and ingression with the cap material type. The complete isolation of the worm and observation of ultrastructure of integument will provide the fundamental data which is important in the nematode research including C. hepatica.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.68-77
• /
• 2006

The heartwood of cengal (Neobalanocarpus heimii) is known to have a high degree of decay resistance by virtue of its high extractive content. After 30 years in ground contact an utility pole of this tropical hardwood was found to be degraded only in the surface layers by cavity-forming soft rot fungi. The present work was undertaken 1) to characterize the degradation of cengal heartwood from the aspect of ultrastructure and chemistry and 2) to investigate the correlation between soft rot decay and its extractive microdistribution in wood tissues. The chemical analysis of cengal heartwood revealed the presence of a high amount of extractives as well as lignin. The wood contained a relatively high amount of condensed lignin and the guaiacyl units. Microscopic observations revealed that vessels, fibers and parenchyma cells (both ray and axial parenchyma) all contained extractives in their lumina, but in variable amounts. The lumina of fibers and most axial parenchyma were completely or almost completely filled with the extractives. TEM micrographs showed that cell walls were also impregnated with extractives and that pit membranes connecting parenchyma cells were well coated and impregnated with extractives. However, fungal hyphae were present in the extractive masses localized in cell lumina, and indications were that the extractives did not completely inhibit fungal growth. The extent of cell wall degradation varied with tissue types. The fibers appeared to be more susceptible to decay than vessels and parenchyma. Middle lamella was the only cell wall region which remained intact in all cell types which were severely degraded. The microscopic observations suggested a close correlation between extractive microdistribution and the pattern and extent of cell wall degradation. In addition to the toxicity to fungi, the physical constraint of the extractive material present in cengal heartwood cells is likely to have a profound effect on the growth and path of invasion of colonizing fungi, thus conferring protection to wood by restricting fungal entry into cell walls. The presence of relatively high amount of condensed lignin is also likely to be a factor in the resistance of cengal heartwood to soft rot decay.

• The Journal of Engineering Geology
• /
• v.15 no.3
• /
• pp.257-268
• /
• 2005

In situ rock mass is generally heterogeneous and discontinuous, with varying degrees of strength along the planes of weakness. The planes of weakness such as joints, faults, cracks and bedding planes, control the strength and deformation characteristics of the rock mass. Subsequently, the stability of underground opening depends upon the spatial distribution of discontinuities and their mechanical properties in relation with geometrical shape of openins as well as the mechanical properties of intact rock materials. Understanding the behaviour of a discontinuous rock mass remains a key issue for improving excavation design in hiかy stressed environments. Although recent advances in rock mechanics have provided guidelines for the design of underground opening in isotropic rock mass, prediction and control of deformation in discontinuous rock masses are still unclear. In this study, parametric study was performed to investigate the plastic zone size, stress distribution and deformation behavior around underground opening in a discontinuous rock mass using a continuum joint model. The solutions were obtained by an elasto-plastic finite difference analysis, employing the Mohr-Coulomb failure criteria. Non-associated flow rule and perfectly plastic material behavior are also assumed.