• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.6
• /
• pp.43-49
• /
• 2015

In this paper, we propose enhanced wireless power transfer system based on magnetic resonance for portable electronic device charging. Resonators were designed and fabricated for efficiency improvement and miniaturization through electromagnetism simulation using HFSS(High Frequency Structure Simulator). Impedance matching network is employed to minimize reflections that is caused by difference between input impedance and output impedance. Receiver IC that consist of rectifier and Low Drop Out(LDO) regulator were designed and fabricated to reduce power loss. This chip is implemented in $0.35{\mu}m$ BCD technology. A maximum overall efficiency of 73.8% is determined for the system through experimental verification.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2374-2381
• /
• 2007

.We have studied to obtain the properly conditions about impedance matching of the SAW filter for the SPUDT type and the bidirectional transducer type later. And we have studied to obtain the SAW filter for the Slanted Finger Interdigital Transducer(SFIT), was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator In case the SPUDT, we have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are $5000{\AA}$ and $3.6{\mu}m$, respectively. And the of the bidirectional transducer, the width of IDT' fingers and the space between IDT' finger and reflector is $1.8{\mu}m$, respectively. Also, we have performed to series connected the SPUDT type with the bidirectional transducer type filter. The frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bahdwidth at the 3dB is probably 5.3MHz after when we have matched impedance. Also, we could obtain that ripple characteristics is less than 0.3dB and insert loss is probably -20dB after when we have matched impedance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.3
• /
• pp.269-276
• /
• 2016

This paper presents a 2.65 GHz Doherty power amplifier with internally-matched GaN HEMT. Internal matching circuits were adopted to match its harmonic impedances inside the package. Simultaneously, due to the partially matched fundamental impedance, input and output matching networks become simpler. Bond wires and parasitic elements of transistor package were predicted by EM simulation. For the LTE signal with 6.5 dB PAPR, the implemented Doherty power amplifier shows a power gain of 13.0 dB, a saturated output power of 55.4 dBm, an efficiency of 49.1 %, and ACLR of -26.3 dBc at 2.65 GHz with an operating voltage of 48 V.

• ETRI Journal
• /
• v.39 no.1
• /
• pp.51-61
• /
• 2017

This paper demonstrates a systematic approach for the design of broadband, high efficiency, high power, Class-AB RF amplifiers with high gain flatness. It is usually difficult to simultaneously achieve a high gain flatness and high efficiency in a broadband RF power amplifier, especially in a high power design. As a result, the use of a computer-aided simulation is most often the best way to achieve these goals; however, an appropriate initial value and a systematic approach are necessary for the simulation results to rapidly converge. These objectives can be accomplished with a minimum of trial and error through the following techniques. First, signal gain variations are reduced over a wide bandwidth using a proper pre-matching network. Then, the source and load impedances are satisfactorily obtained from small-signal and load-pull simulations, respectively. Finally, two high-order Chebyshev low-pass filters are employed to provide optimum input and output impedance matching networks over a bandwidth of 100 MHz-500 MHz. By using an EM simulation for the substrate, the simulation results were observed to be in close agreement with the measured results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.2
• /
• pp.151-158
• /
• 2012

This paper proposes a H-plane 8-way rectangular waveguide power divider using Y-junction. A general N-way power divider can be composed of multi-stage T-junctions. However, if the distances of output ports are close, the matching characteristic is not improved by using only T-junctions because of space limitation. In this case, since other types of 3-port junctions should be used to final output stage, Y-junctions are used with T-junctions in this paper. The proposed Y-junction uses the tapered-line impedance transformer and inductive irises to improve impedance matching characteristic. The 8-way power divider using Y-junction is fabricated and measured. The measured return loss and insertion loss from input port to output port are -30.8 dB and -9.3 dB at operating frequency, respectively. The measured maximum phase difference is about $1^{\circ}$. Therefore, the proposed power divider will be useful to apply to various microwave systems, which need to divide the input power equally, such as feed networks for array antennas.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.166-172
• /
• 2001

A RF wideband receiver for INMARSAT-B satellite communications system was composed of low noise amplifier and high gain amplifier, The low noise amplifier used to the resistive decoupling circuit for input impedance matching and self-bias circuits for low noise. The high gain amplifier consists of matched amplifier type to improve receiver gain. The active bias circuit can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver implemented here show more than 60 dB in gain and less than 1.8:1 in input and output voltage standing wave ratio(VSWR), especially the carrier to noise ratio which is input signal level -126.7 dB m at 1537.5 MHz is a 45.23 dB /Hz at a 1.02 kHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.351-354
• /
• 2017

In this paper, a compact MIMO(Multiple Input Multiple Output) antenna for smart glasses is proposed. The proposed MIMO antenna is designed using T-shaped isolator inserted between two closely located Inverted-F Antenna(IFA) and using two slots located in the ground for isolation enhancement and impedance matching characteristic. The proposed antenna has only the overall dimensions of $35mm{\times}9mm{\times}0.8mm$ and operates in the 2.4 GHz industrial, scientific, and medical(ISM) band. To verify human body effect, the phantom is used for antenna performance. The measured specific absorption rate(SAR) value is 1.38 W/kg with an input power of 18 dBm. The performance of the proposed antenna is compared with that of previous works for verification.

• Journal of Broadcast Engineering
• /
• v.19 no.6
• /
• pp.934-941
• /
• 2014

In this paper, we present a low profile 2-layered meander built-in monopole antenna for portable RFID reader using FDTD(Finite Difference Time Domain) method. The input impedance, return loss, and VSWR in the frequency domain are calculated by Fourier transforming the time domain results. The double meander 2-layer structure is used to enhance the impedance matching and increase the antenna gain. The measured bandwidth of the antenna is 0.895 GHz ~ 0.930 GHz for a S11 of less than -10dB. The measured peak gain of proposed low profile RFID built-in antenna is 2.3 dBi. And the proposed built-in antenna for portable RFID reader can offers relatively wide-bandwidth and high-gain characteristics, in respectively. Experimental data for the return loss and the gain of the antenna are also presented, and they are relatively in good agreement with the FDTD results. This antenna can be also applied to mobile communication field, energy fields, RFID, and home-network operations, broadcasting, and other low profile mobile systems.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.1
• /
• pp.7-13
• /
• 2014

In this paper, a novel waveguide low pass filter for satellite communication is proposed. The proposed low pass filter is designed to obtain wideband characteristics without the interference of higher order modes, sufficient attenuation in the stop-band and small sized lightweight characteristics by evanescent-mode ridge structure. To improve return loss and rejection loss, rectangular ring is inserting around the ridges in the waveguide. Input and output ports of the low pass filter is designed by using the impedance step structure for the impedance matching of the filter. The proposed waveguide low pass filter is fabricated and then measured as return loss over 19.5 dB, insertion loss less than 1.41 dB at the pass-band of 7.25 ~ 8.4 GHz and rejection loss over 67.2 dB at the stop-band of 12.25 ~ 14.5 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.9
• /
• pp.1070-1076
• /
• 2007

In this paper, we study the characteristics of dual band microstrip antenna with the wedge-shaped radiation patch added the slot using air substrate. Wedge-shaped patch antenna with air substrate is avoided the large probe reactance associated with a thick substrate owing to the use of short probe and good impedance matching over a wide frequency range can be obtained. Slot on the antenna radiator varies the reactance component according to the employed frequency and affect the resonance freaqency of the antenna, therefore the antenna can resonate at the dual band(cellular and PCS band). The slot length and position have an effect on the bandwidth and input impedance of the antenna are optimized by simulation. From the experiment results for the fabricated antenna, -10 dB of $S_{11}$ is content with the allocated bandwidth of Cellular and PCS system and - 15 dB of cross polarization level. From the results of this paper, it has been confirmed that the proposed antenna can be used as the base station antenna fur Cellular and PCS band.