• Korean Journal of Remote Sensing
• /
• v.38 no.4
• /
• pp.343-353
• /
• 2022

An attempt to derive the surface temperature from the Korea Multi-purpose Satellite (KOMPSAT)-3A mid-wave infrared (MWIR) data acquired over the southern California on Nov. 14, 2015 has been made using the MODerate resolution atmospheric TRANsmission (MODTRAN) radiative transfer model. Since after the successful launch on March 25, 2015, the KOMPSAT-3A spacecraft and its two payload instruments - the high-resolution multispectral optical sensor and the scanner infrared imaging system (SIIS) - continue to operate properly. SIIS uses the MWIR spectral band of 3.3-5.2 ㎛ for data acquisition. As input data for the realistic simulation of the KOMPSAT-3A SIIS imaging conditions in the MODTRAN model, we used the National Centers for Environmental Prediction (NCEP) atmospheric profiles, the KOMPSAT-3Asensor response function, the solar and line-of-sight geometry, and the University of Wisconsin emissivity database. The land cover type of the study area includes water,sand, and agricultural (vegetated) land located in the southern California. Results of surface temperature showed the reasonable geographical pattern over water, sand, and agricultural land. It is however worthwhile to note that the surface temperature pattern does not resemble the top-of-atmosphere (TOA) radiance counterpart. This is because MWIR TOA radiances consist of both shortwave (0.2-5 ㎛) and longwave (5-50 ㎛) components and the surface temperature depends solely upon the surface emitted radiance of longwave components. We found in our case that the shortwave surface reflection primarily causes the difference of geographical pattern between surface temperature and TOA radiance. Validation of the surface temperature for this study is practically difficult to perform due to the lack of ground truth data. We therefore made simple comparisons with two datasets over Salton Sea: National Aeronautics and Space Administration (NASA) Jet Propulsion Laboratory (JPL) field data and Salton Sea data. The current estimate differs with these datasets by 2.2 K and 1.4 K, respectively, though it seems not possible to quantify factors causing such differences.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.896-905
• /
• 2004

In this paper, the design, fabrication and experiment on a planar array antenna with a flat-topped radiation pattern for a mobile base station antenna were described. The current distribution of an antenna aperture, which is easily realizable in a feeding network compared with the conventional one of sin(x)/x was optimized for shaping a desired flat-topped radiation pattern. The planar array antenna designed in this paper has a rectangular lattice and is composed of array elements of 16${\times}$8. Each radiating element, which is a microstrip element fed coaxially, has a linear vertical polarization and the feed network which use a Wilkinson power divider and a 180$^{\circ}$ ring hybrid coupler as a base element is designed. The flat-topped radiation pattern with 90$^{\circ}$ is shaped by 16 array elements with the element spacing of 0.55 λ$_{ο}$ in the azimuth plane, and the normal radiation pattern with 10$^{\circ}$ is shaped by 8 array elements with the element spacing of 0.65 λ$_{ο}$ in the elevation plane. Also, the planar array antenna is symmetrically divided into four parts. It consists of one hundred-twenty-eight radiating elements, thirty-two 1-4 column dividers, low 1-8 row dividers and one 1-4 input power divider. In order to verify electrical performances of the planar way antenna proposed in this paper, the experimental breadboard operated in tile band of 1.92～2.17 GHz(IMT2000 band) was fabricated, and its experimental results were a good agreement with simulation ones.

• Journal of the Korean Society of Costume
• /
• v.19
• /
• pp.105-125
• /
• 1992

The research, aiming an automatic pattern design of Korean Costume by utilizing CAD system, tried Grading, Seaming and Marking with a theme of girl's color-strip blouse & skirt. The content & conclusion of the research can be outlined as follows; 1) As we reviewed the current situation of Korean costume which becomes more likely celebrational or festival costume, while the demand of it is getting increase, it's being dealt mostly as ready-made dresses with different qualities & designs. Especially childrens ready-made ones were highly demanded to be picked up as the theme. 2) For the original drawing of children's color-strip blouse & skirt, Kyung-Ja Park's drawing method was used here, and for the substitute of particular body parts absolute size, Joo-Won Lee's standard size chart from a size-study by ages. 3) To work with CAD system we had input master pattern, drawn for age 5 as basic size, then graded six step-sizes for 1-11 years old. For add-subtract of particular body parts size, we graded through computing the standard variation among items to get the pattern developed into ready-made standard size, we can make precise plotting by grading wanted size very rapidly if we correct the rule of changed items different from standard size to make utilization possible enough with easy order method of ready-made Korean Dress. 4) We produced Marker after attaching a margin to seam accordingly by parts for each pattern using P/D/S to mark, In mass gament-cutting, the loss of time and material can minimized. In this research the apparel CAD system which has been utilized and only be western fashion industry was introduced for the design of ready-made Korean costume and utilized it in Grading, Marking which are critical steps to improve productivity and have reported the result in the research. Thus we expect that less cost, improved productivity and better quality with minimized loss of material from marking as well as from prompt and precise size-drawing. Furthermore the utilization of CAD system is considered as an effective one in terms of the research & the development to remove effective one in terms of the research & the development to remove irrational elements in the design and production process of Korean costume as well as in terms of the study of Korean Costume development through creative works of Korean Costume.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.6
• /
• pp.564-572
• /
• 2019

Numerical simulation of the sediment by the Delft3d model was conducted to examine the changes in the sediment budget transport caused by long-term wave changes at the Maengbang beach. Representative waves were generated with input reduction tools using NOAA NCEP wave data for about 40 years, i.e., from January 1979 to May 2019. To determine the adequacy of the model, wave and depth changes were compared and verified using wave and depth data observed for about 23 months beginning in March 2017. As a result of the error analysis, the bias was 0.05 and the root mean square error was 0.23, which indicated that the numerical wave results were satisfactory. Also, the observed change in depth and numerical result were similar. In addition, to examine the effect due to long-term changes in the waves, the NOAA wave data classified into each of the representative wave grades, and then the annual trend of the representative wave was analyzed. After deciding the weight of each wave class considering the changed wave environment in 2100, the amounts of sedimentation, deposition, and the sediment transport budget were reviewed for the same period. The results indicated that the sedimentation pattern did not change significantly compared to the current state, and the amount of the local sediment budget shown in the present state was slightly less. And there has been a local increase in the number of sediment budget transport, but there is no significant difference in the net and amount of sediment movements.

• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.9-14
• /
• 2008

In this paper, a new type of Yagi-Uda antenna that operates in the terahertz frequencies is designed. The proposed Yagi-Uda antenna can obtain high input resistance of approximately $2000{\Omega}$ at the resonance frequency by using a full-wavelength dipole instead of a half-wavelength dipole as the driver element. The current leakage into the bias line was minimized by applying the photonic bandgap structure to the bias line. By designing the antenna on a thin substrate, the impedance lowering of an antenna caused by the relative dielectric constant of the substrate was prevented and the end-fire radiation pattern which is the original radiation characteristic of the Yagi-Uda antenna could be obtained. We expect that the proposed Yagi-Uda antenna can achieve increased terahertz output power by improving the impedance mismatching problem with the photomixer.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1743-1750
• /
• 2003

DC motor requires a rotor speed sensor for accurate speed control. The speed sensors such as resolvers and encoders are used as a speed detector, but they increase cost and size of the motor and restrict the industrial drive applications. So in these days, many papers have reported in the sensorless operation of DC motor〔3­5〕. This paper presents a new sensorless strategy using neural networks〔6­8〕. Neural network has three layers which are input layer, hidden layer and output layer. The optimal neural network structure was tracked down by trial and error, and it was found that 4­16­1 neural network structure has given suitable results for the instantaneous rotor speed. Also, learning method is very important in neural network. Supervised learning methods〔8〕 are typically used to train the neural network for learning the input/output pattern presented. The back­propagation technique adjusts the neural network weights during training. The rotor speed is gained by weights and four inputs to the neural network. The experimental results were found satisfactory in both the independency on machine parameters and the insensitivity to the load condition.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.2
• /
• pp.80-87
• /
• 1999

This paper proposed a high impedance fault detection method using a neural network on distribution lines. The $\upsilon-i$ characteristic curve was obtained by high impedance fault data tested in various soil conditions. High impedance fault was simulated using EMTP. The pattern of High Impedance Fault on high density pebbles was taken as the learning model, and the neural network was evaluated on various soil conditions. The average values after analyzing fault current by FFT of even.odd harmonics and fundamental rms were used for the neural network input. Test results were verified the validity of the proposed method .ethod .

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.3
• /
• pp.663-670
• /
• 1998

Most of feedback shift controllers developed in the past have fixed control parameters tuned by experts using a trial and error method. Therefore, those controllers cannot satisfy the best control performance under various driving conditions. To improve the shift quality under various driving conditions, a new self-organizing controller(SOC) that has an optimal control performance through self-learning of driving conditions and driver's pattern is designed in this study. The proposed SOC algorithm for the shift controller uses simple descent method and has less calculation time than complex fuzzy relation, thus makes real-time control passible. PCSV (Pressure Control Solenoid Valve) control current is used as a control input, and turbine speed of the torque converter is used indirectly to monitor the transient torque as a feedback signal, which is more convenient to use and economic than the torque signal measured directoly by a torque sensor. The results of computer simulations show that an apparent reduction of shift-transient torque is obtained through the process of each run without initial fuzzy rules and a good control performance in the shift-transient torque is also obtained.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.2
• /
• pp.1-13
• /
• 2011

The recent spotlight on electronic touch-screen display, a rapid breakthrough in the information society is evolving. Touch panel input device such as a keyboard or mouse without the use of, the on-screen character or a specific location or object on the person's hand touches a particular feature to identify the location of a panel is to be handled. The touch screen on the touch panel is used in the Ag paste is used mostly for low-curable paste. The thermal-curing paste according to the drying process of thermal energy consumption and improve the working environment of organic solvents have problems. In this study, Ag paste used in the non-thermal curing friendly and cost-effective UV curable paste was prepared. Current commercially available thermal-curable binder, was used instead of the flow characteristics of UV-curable oligomers and monomers with functional groups to give a single conductive Ag paste with the addition of a pattern could be formed. Ag paste as a result, thermal-curing adhesive, hardness, resistance and excellent reproduction of fine patterns and was available with screen printing environmentally friendly could see its potential as a patterning technology.

• The Journal of Korea Robotics Society
• /
• v.8 no.3
• /
• pp.143-149
• /
• 2013

This paper presents a new miniature haptic display to convey ample haptic information to a user of a handheld interface. There are buttons on interfaces or general electronic devices, but existing buttons provide haptic feedback of only one passive pattern to a user. Because humans perceive tactile and kinesthetic information simultaneously when they handle objects the proposed actuator provides both sensations at once. It is able to generate various levels of kinesthetic sensations when pressing a button under diverse situations. Also, vibrotactile feedback can be delivered for exciting haptic effects with numerous patterns. Its performance was evaluated in accordance with the resistive force by changing the intensity of the input current. Experiments show that the proposed actuator has the ability to provide numerous haptic sensations for more realistic and complex haptic experiences.