• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.126-131
• /
• 2001

This paper deals with implementation of inverter systems for DC power regeneration, which can regenerate the excessive DC power from DC bus line to AC supply in substations for traction systems. From the viewpoint of both power capacity and switching losses, a three-phase square-wave inverter system is adopted. To control the regenerated power, the magnitude and phase of fundamental output voltages should be appropriately controlled in spite of the variation of input DC voltage. Inverters are operated with modified a-conduction mode to fix the potential of each arm. The overall system consists of the line-to-line voltage and line current sensors, an actual power calculator using d-q transformation method, a complex power controller with PI control scheme, a gating signal generator for modified $\alpha-conduction\;mode\;with\;\delta\;and\;\alpha$, a DPLL for frequency followup, and power circuit.

• 산업경영시스템학회지
• /
• 제20권41호
• /
• pp.33-40
• /
• 1997

The main objective of this study is to analysis the relationship between productivity measurement model which describe and explain R&D(Research & Development) productivity based on production function of Cobb-Douglas and the structure of the R&D investment. The model focuses on the variables related to R&D investment in order to measure the efficiency of R&D largely. So, the proposed model describe the relationship between output(or / input) and factors of production such as capital cost, labor cost and R&D expense, etc. These factors are associated with a signigicant positive correlation between productivity and R&D investment.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.54-58
• /
• 1997

In this study, study, about Automatic Loader and Unloader system which can directly be used for material handing and tool operating is moving linear transfer system for mainly forming of small electronic unit and other at press line. This system for been installed in a press in order to load and unload a workpiece from a press die. Control method be used Programmable logic control(PLC) unit. other Control equipment of system is Motor drive, Positioning Control and so on. It took data of input from each sensor and send signal of output to actuator by sequence program. We try to Characteristics test of this system has good condition when operating by laser measurement

• Journal of electromagnetic engineering and science
• /
• 제16권4호
• /
• pp.241-247
• /
• 2016

This paper proposes the design and measurement of a 6-18 GHz front-end receiver module that has been combined into a one- channel output from a two-channel input for electronic warfare support measures (ESM) applications. This module includes a limiter, high-pass filter (HPF), power combiner, equalizer and amplifier. This paper focuses on the design aspects of reducing the noise figure (NF) and matching the phase and amplitude. The NF, linear equalizer, power divider, and HPF were considered in the design. A broadband receiver based on a combined configuration used to obtain low NF. We verify that our receiver module improves the noise figure by as much as 0.78 dB over measured data with a maximum of 5.54 dB over a 6-18 GHz bandwidth; the difference value of phase matching is within $7^{\circ}$ between ports.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.97-101
• /
• 1993

In this work, the imaginary part of the inner modulation transfer function of the cutting dynamics is introduced for tool wear monitoring. Time-series method is utilized to construct the generalthree dimensional cutting dynamics whose imaginary part of the inner modulation transfer funcition shows the proportionality to tool wear at the natural frequency of the machine tool dynamics. This modelis reduced to single-input single- output model without altering the proporitonality characteristics to tool wear and implemented to the dual computer system in which one computer performs measurement while the other calculates the imaginary part of the inner modulation transfer function of th cutting dynamics by the batchleast square method. The values of the imaginary part at the natural frequencyof the machine tool structure in the cutting direction are compared to the one calculated during machining with a brand new tool to decide the current stants of the tool. The experiments shows the relevance of the proposed concept.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.579-584
• /
• 2009

This paper describes a power quality analysis of a photovoltaic generating systems. Prior to the power measurement, domestic and foreign codes related to the photovoltaic generating systems were briefly summarized. After constructing about 5 kW photovoltaic systems, input/output voltages and currents were measured to compare and analyze the power quality by the module type. Based on the measured values, a couple of factors such as active power, power factor, total harmonic distortion(THD) was calculated and analyzed.

• ETRI Journal
• /
• 제25권5호
• /
• pp.379-386
• /
• 2003

This paper presents the design of a narrow-band channel filter and its group-delay equalizer for a Ka-band satellite transponder. We used an 8th order channel filter for high selectivity with an elliptic-integral function response and an inline configuration. We designed a 2-pole, reflection-type, group-delay equalizer to compensate for the steep variation of the group-delay at the output of the channel filter, keeping the thermal stability at ${\pm}7$ ns of group-delay variation at the band edges over 15-55$^{\circ}C$. We devised a new tuning technique using short-ended dummy cavities and used it for tuning both the filter and equalizer; this removes the necessity of additional tuning after the cavities are assembled. Through measurement, we demonstrate that the group-delay-equalized filter meets the equipment requirements and is appropriate for satellite input multiplexers.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2528-2530
• /
• 2004

Neural network minimization problems are often conditioned and in this contribution way to handle this will be discussed. It is shown that a better conditioned minimization problem can be obtained if the problem is separated with respect to the linear parameters. This will increase the convergence speed of the minimization. One of the most powerful uses of neural networks is in function approximation(curve fitting)[1]. A main characteristic of this solution is that function (f) to be approximated is given not explicitly but implicitly through a set of input-output pairs, named as training set, that can be easily obtained from calibration data of the measurement system. In this context, the usage of Neural Network(NN) techniques for modeling the systems behavior can provide lower interpolation errors when compared with classical methods like polynomial interpolation. This paper solve of single-variable minimization using neural network.

• 한국정밀공학회지
• /
• 제18권9호
• /
• pp.71-81
• /
• 2001

This paper analyzes the effectiveness of minimizing vibration and sound transmission on/through a thin rectangular plate by both feedback control and hybrid control which combines adaptive feedforward control with a feedback loop. An experimental system identification technique using the matrix-fractional curve-fitting of the frequency response data is introduced for complex shaped structures. This identification technique reduces the model order o the MIMO(Multi-Input Multi-Output) system which simplifies the practical implementation. The adaptive feedforward control uses a Multiple filtered-x LMS(Least Mean Square) algorithm and the feedback control uses a multivariable digital LQG(Linear Quadratic Gaussian) algorithm. Experimental results show that an effective reduction of sound transmission is achieved by the hybrid control scheme when both vibration and noise measurement signals are incorporated in the controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.104-107
• /
• 1999

Tracking control of an arbitrary reference has been discussed for 7Th order 2-input 2-output non-minimum phase EGR/VGT diesel engines. To meet strict emission regulations and customer demands, the desired set points, the air-fuel ratio and the ERG flow fraction, determined from a static engine data based on engine speed and the desired fueling rate are transformed into the set points for the two sensor measurement outputs. Applying the sliding mode tracking control theory proposed by Jeong and Utkin, two step design was carried out using the bounded solution of an unstable zero dynamics for the given reference signals. This paper shows through simulations how stabilization of unstable zero dynamics and reference tracking can be accomplished simultaneously.