• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.6
• /
• pp.542-547
• /
• 2012

Until recently, most of GCS(Ground Control Software) has been required to visualize attitude, position, status of vehicle and to transmit control and mission commands for a single UAV(Unmanned Aerial Vehicle). However, the GCS needs to expand its functions to handle more complex situations. Simultaneous operation of multiple UAVs is emerging as a new practice. Hence, we set up requirements for operation of multiple UAVs and suggest the architecture of GCS that satisfy the requirements. In this study, we analyze the upper requirements and define the total structure of GCS at first. Then we design the inner structure for requirements in detail. Finally, we verify the functions of GCS on PILS(Processor In the Loop Simulation) System.

• Journal of the Society of Disaster Information
• /
• v.13 no.4
• /
• pp.537-549
• /
• 2017

Wooden houses are classified into Traditional, Modern, Platform, Timber framing types. The most popular type is Platform framing which is come from foreign culture. The foreign and Korean tree structure tend to be incompatible with Korean culture and don't fit well with modern lifestyle. In this study, it will analyze the design characteristics of the traditional and modern wooden house to solve these problems. The design characteristics will be contributed to the development of wooden architecture which is suitable for Korean architectural style and lifestyle The research consists of space analysis, plane analysis, structural system analysis, roof type analysis, and aesthetic analysis. From the analytical results the design characteristics of traditional Hanok and modern wood structure, we propose the modular elements and the inner and outer shapes of the Korean - style wooden house.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.10
• /
• pp.1377-1383
• /
• 2014

This paper deals with eddy current loss of magnetic coupling with radial permanent magnet (PM) using analytical method such as a space harmonic method. Superposition of two kinds analysis model is used to analyze eddy current loss induced in inner PM and outer PM of magnetic coupling. When the eddy current is induced, the environmental temperature increases, and the permanent magnet(PM) characteristics are degraded because the performance of PM is greatly influenced by temperature rise. Hence, the calculation of eddy current loss becomes an important factor in the magnetic coupling. In order to analyze eddy current loss, first, on the basis of the magnetic vector potential and two-dimensional(2-D) polar-coordinate system, the magnetic field solutions of the radial magnetized PM are obtained. And we obtain the analytical solutions for the eddy current density produced by permanent magnet. Lastly, analytical solutions for eddy current loss are derived by using equivalent, electrical resistance calculated from magnet volume and analytical solution for eddy current density. This analytical results are validated by comparing with the 2-D finite element analysis (FEA).

• Journal of Surface Science and Engineering
• /
• v.50 no.5
• /
• pp.339-344
• /
• 2017

Highly corrosion resistance performance of CrAlSiN coatings were obtained by applying ultrathin $Al_2O_3$ thin films using atomic layer deposition (ALD) method. CrAlSiN coatings were prepared on Cr adhesion layer/SUS304 substrates by a hybrid coating system of arc ion plating and high power impulse magnetron sputtering (HiPIMS) method. And, ultrathin $Al_2O_3$ passivation layer was deposited on the CrAlSiN/Cr adhesion layer/SUS304 sample to protect CrAlSiN coatings by encapsulating the whole surface defects of coating using ALD. Here, the high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and energy dispersive X-ray spectrometry (EDX) analysis revealed that the ALD $Al_2O_3$ thin films uniformly covered the inner and outer surface of CrAlSiN coatings. Also, the potentiodynamic and potentiostatic polarization test revealed that the corrosion protection properties of CrAlSiN coatings/Cr/SUS304 sample was greatly improved by ALD encapsulation with 50 nm-thick $Al_2O_3$ thin films, which implies that ALD-$Al_2O_3$ passivation layer can be used as an effect barrier layer of corrosion.

• Korean Institute of Interior Design Journal
• /
• no.5
• /
• pp.45-52
• /
• 1995

Frank Lloyd Wright, a master of the 20th Century Ar-chitecture, contributed tremendously in creating a wholly new form of American architecture called Prairie Style. His idea behind the development of the building structur-al system, organic relationships between inner and outer space, horizontal vertical lines, and idea of extending and expanding interior spaces came from nature. He had completed over 390 projects throughout his life and 90% of those projects were residential design. The most typical characteristic shared by many of his residential design was that each design element, whether it is functional or aesthetical, has close relationship to or-ganic nature, human scale, theoretical floor plants, and maximum emphasis on horizontal lines in respect to na-ture. His concept of "flow of spaces" reformed common the-ory of room next to room in a enclosed space. His sense of "wall" was no longer the side of a box. Careful selec-tion of finishing materials, colors, and natural images en-hance the design as well. F.L. Wright was an artist, designer, and architect who believed the exterior space should have direct relationship to the interior space. His architectural philosophy was not only to design exterior of architecture but also to ful-fill his space through the careful development of interior elements such as furniture, and lighting fixture. Even the patterns for leaded glass windows were designed to have unified appearance from outside to inside of the house. The objective of this study was to analyze floor plans, spatial organizations, and interior design elements of the houses which represent the best of F.L. Wright's design principles and philosophy behind Prairie Style. The meth-od used to collect informations for this study was based on books, articles, journals, and actual site visits. actual site visits.

• Nuclear Engineering and Technology
• /
• v.31 no.5
• /
• pp.486-497
• /
• 1999

The local heat transfer coefficient is experimentally investigated for the reflux condensation in a countercurrent flow between the steam-air mixture and the condensate, A single vertical tube has a geometry which is a length of 2.4m, inner diameter of 16.56mm and outer diameter of 19.05mm and is made of stainless steel. Air is used as a noncondensible gas. The secondary side has a shape of annulus around vertical tube and the lost heat by primary condensation is transferred to the coolant water. The local temperatures are measured at 11 locations in the vertical direction and each location has 3 measurement points in the radial direction, which are installed at the tube center, at the outer wall and at the coolant side. In three different pressures, the 27 sets of data are obtained in the range of inlet steam flow rate 1.348∼3.282kg/hr, of inlet air mass fraction 11.8∼55.0%. The investigation of the flooding is preceded to find the upper limit of the reflux condensation. Onset of flooding is lower than that of Wallis' correlation. The local heat transfer coefficient increases as the increase of inlet steam flow rate and decreases as the increase of inlet air mass fraction. As an increase of the system pressure, the active condensing region is contracted and the heat transfer capability in this region is magnified. The empirical correlation is developed by 165 data of the local heat transfer. As a result, the Jacob number and film Reynolds number are dominant parameters to govern the local heat transfer coefficient. The rms error is 17.7% between the results by the experiment and by the correlation.

• Korean Journal of Poultry Science
• /
• v.23 no.1
• /
• pp.9-17
• /
• 1996

This study was conducted to compare the survival rate of chick embryos among different eggshell window positions and to search for the most appropriate injection position. The eggshells were punctured at blunt-end, sharp-end and side-up with a sterilized fine forceps, respectively. The survival rate of sharp-end window was higher than the other window positions. Injection of Dulbecco’s modified eagle’s medium (DMEM) through blunt-end window (BE1) was impossible because inner cell membrane was obscure. The 2 ${\mu}$L DMEM was injected into 2.5 d-old embryo blood vessel through sharp end window. To prevent hemorrhages at the point of injection, the air bubbles were injected into the embryo blood vessel. The survival rate of chicks embryo in sharp end window was about 17.0％. Therefore, this sharp-end window system will be helpful for the production of germline chimera or transgenic chicken using primordial germ cells ( PGCs ).

• International Journal of Quality Innovation
• /
• v.7 no.1
• /
• pp.60-89
• /
• 2006

In the Knowledge-based Economic Era, all of the enterprises are facing global competitive pressure. The activities of knowledge accessing, codifying, and application will obviously become the main inner function on enterprise operation. Knowledge will be the primary competitive advantage; therefore, he who wants to hold the competitive advantage should do the knowledge management (KM) very well. In this study, we construct the research dimensions and variances by the successful factors of KM, which had been practiced very well by big enterprises inside and outside our country, and which was recommended by the related scholars. In order to approach the differences between big enterprises and small and medium-sized enterprises (SMEs) towards implementing KM, this study takes the way of questionnaire investigation to do empirical analysis and to construct the model of KM by path analysis. The study found out when implementing KM, SMEs should highlight 'leadership,' 'library-architecture,' and 'corporate culture' these three aspects, while 'information technology' and 'performance evaluation' these two aspects show no remarkable influence. It shows that he who wants to construct KM might not too overweight on information technology to build the KM system. Therefore, we suggest when implementing KM, enterprises should reinforce the corporate culture by sharing, organized KM process, learning environment for all employees, and highly authorization by top managers in order to reach the expectant success of KM. The result of this study offers practical thinking directions to reach the expectant success for the policy makers in SMEs, who are accessing to or evaluating to implement KM.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.456-463
• /
• 2005

This paper describes a design process of end-milling cutters: solid model of the designed cutter is constructed along with computation of cutter geometry, and the wheel geometry as well as wheel positioning data fur fabricating end-mills with required cutter geometry is calculated. In the process, the main idea is to use the cutting simulation method by which the machined shape of an end-milling cutter is obtained via Boolean operation between a given grinding wheel and a cylindrical workpiece (raw stock). Major design parameters of a cutter such as rake angle, inner radius can be verified by interrogating the section profile of its solid model. We studied relations between various dimensional parameters and proposed an iterative approach to obtain the required geometry of a grinding wheel and the CL data fer machining an end-milling cutter satisfying the design parameters. This research has been implemented on a commercial CAD system by use of the API function programming, and is currently used by a tool maker in Korea. It can eliminate producing a physical prototype during the design stage, and it can be used fur virtual cutting test and analysis as well.

• Journal of Preventive Medicine and Public Health
• /
• v.44 no.6
• /
• pp.242-248
• /
• 2011

Objectives: Busan is reported to have the highest mortality rate among 16 provinces in Korea, as well as considerable health inequality across its districts. This study sought to examine overall and cause-specific mortality and deprivation at the town level in Busan, thereby identifying towns and causes of deaths to be targeted for improving overall health and alleviating health inequality. Methods: Standardized mortality ratios (SMRs) for all-cause and four specific leading causes of death were calculated at the town level in Busan for the years 2005 through 2008. To construct a deprivation index, principal components and factor analysis were adopted, using 10% sample data from the 2005 census. Geographic information system (GIS) mapping techniques were applied to compare spatial distributions between the deprivation index and SMRs. We fitted the Gaussian conditional autoregressive model (CAR) to estimate the relative risks of mortality by deprivation level, controlling for both the heterogeneity effect and spatial autocorrelation. Results: The SMRs of towns in Busan averaged 100.3, ranging from 70.7 to 139.8. In old inner cities and towns reclaimed for replaced households, the deprivation index and SMRs were relatively high. CAR modeling showed that gaps in SMRs for heart disease, cerebrovascular disease, and physical injury were particularly high. Conclusions: Our findings indicate that more deprived towns are likely to have higher mortality, in particular from cardiovascular disease and physical injury. To improve overall health status and address health inequality, such deprived towns should be targeted.