• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.6
• /
• pp.317-323
• /
• 2013

A multi-perforated tube indicates the existence of multiple holes of various shapes on the surface of a long cylinder-type or rectangular tube, and a hole installed on the surface is called an orifice, as it is relatively small in size, compared with the surface area of the tube. In this study, the flow characteristics of a circular multi-perforated tube with many orifices on the surface were investigated experimentally and numerically. The volume flowrate issuing from each orifice, discharge angle, effective flow area ratio, and the flow fields around the orifices were measured and visualized, with the variation of the orifice area ratio, at the same blockage ratio. The volume flowrate distributions along the flow direction of the multi-perforated tube tends to be more uniform, as larger orifices were positioned at the inlet side of the multi-perforated tube, compared with no orifice area change along the flow direction.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.31-41
• /
• 1997

This paper describes a potential-based panel method formulated for the prediction of the steady performance of a waterjet propulsor. The method employs normal dipoles and sources distributed on the solid surfaces such as the impeller/stator blades, hub and duct, and normal dipoles in the shed wakes trailing the impeller and stator to represent the potential flow around the waterjet propulsor. To define a closed boundary surface, the inlet and outlet open boundary surfaces are introduced where the sources and dipoles are distributed. The kinematic boundary condition on the solid boundary surface is satisfied by requiring that the normal component of the total velocity should vanish. On the inlet surface, the total inflow flux into the duct is specified, and on the outlet surface the conservation of mass principle is applied to evaluate the source strength. The solid surfaces are discretized into a set of quadrilateral panel elements and the strengths of sources and dipoles are assumed constant at each panel. Applying this approximation to the boundary conditions leads to a set of simultaneous equations. Systematic numerical tests show that the present numerical method is fast and stable. In order to validate the present method, sample computations are carried out first for the case of a conventional axial flow fan which has a similar geometry as the waterjet propulsor, and then for the case of a waterjet propulsor on which experiments are carried out at KRISO(Korea Research Institute of Ships and Ocean Engineering).

• Journal of Power System Engineering
• /
• v.19 no.2
• /
• pp.57-63
• /
• 2015

In this paper, we developed a continuous sterilizer in order to improve the productivity of the retort product. To this end, we design the sterilizer with a product inlet, outlet, and chain for continuously conveying the retort. The temperature analysis is performed to optimize the design parameters of the internal sterilizer. The experimental apparatus is developed to verify the productivity of the sterilizer based on the temperature analysis. The test is performed to optimize the evaluation parameters using Box-Behnken design method of a response surface methodology. From the test, the productivity of the continuous sterilizer is improved over 1,000 kg/h.

• 한국해양학회지
• /
• v.9 no.2
• /
• pp.10-18
• /
• 1974

The cold water mass around the southeast coast of the Korean Peninsula is analyzed by using CSK data from 1966 through 1970. It is shown that this water mass flows down from the region offshore of Jukbyun to the area of Youngil Bay along the 100meter contour line of bottom topography. In ordinary summer conditions when the current velocity in the Korea Strait is usually above about 50cm/sec and the wind direction is southwest, the cold water ascends to the surface and makes the surface temperature gradient large, unless disturbed by a tropical cyclon. The bottom water of the Korea Strait is formed by the stratification after the Tsushima intermediate water and the Japan Sea intermediate water have been mixed. In winter the Tsushima intermediate water with high salinity sinks rapidly around the inlet of the Japan Sea and prevents the Japan Sea intemediate water from entering the Korea Strait.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.3
• /
• pp.173-182
• /
• 2002

We investigated the effects of operating variables, such as electrical. reactor and gas parameters on toluene removal and discharge property in the dielectric barrier discharge (DBD) process. The toluene removal was initiated with the energy transfer to the reactor by loading of voltages higher than the discharge onset value. The energy transfer and toluene removal increased with the applied voltage. Higher removal rate was observed with smooth surface electrode despite of lower energy transfer compared with the coarse electrode, because more uniform discharge can be obtained on smooth surface state. The decrease of dielectric material thickness enhanced the removal efficiency by increasing the discharge potential. The toluene removal efficiency decreased with the increase of the inlet concentration. The increase of gas retention time enhanced the removal efficiency by the increase of energy density. The oxygen and humidity contents seem to exert significant influences on the toluene removal by dominating the generation of electrons, ions, and radicals which are key factors in the removal mechanism.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.10
• /
• pp.1-8
• /
• 2014

Heat dissipation of the high power LED is a critical issue. To estimate the junction temperature of the LED chip is most important in characterizing the heat dissipation, but it is impossible to directly measure it. In this study, surface temperatures of the 12.8W LED bulb was measured for 5 points using a data logger and compared with the simulated results using a thermal simulator based on FVM (finite volume method) to secure a reliability of the simulation. Effects of some factors such as lens, emissivity and air inlet were investigated using simulation works and then the results were analysed.

• Transactions of Materials Processing
• /
• v.10 no.7
• /
• pp.579-583
• /
• 2001

Shape changes of a workpiece in an Eulerian Finite Element analysis for the steady state, three-roll-stand shape rolling are modelled. Although an Eulerian analysis has many advantages for the steady state rolling problems, it necessitates an assumption about the unknown shape of the control volume. In almost all cases, the assumed control volume does not match the final shape and the control volume should be updated. This update can be accomplished by performing a free surface correction. The final shape of a material point, which has a spherical shape at the inlet, can be also predicted by integrating a deformation gradient along a stream line. Analyses of three-roll-stand shape rolling are performed and the results are discussed in detail.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.328-331
• /
• 2001

Shape changes of a workpiece in an Eulerian Finite Element analysis for the steady state. three-roll-stand shape rolling are modelled. Although an Eulerian analysis has many advantages for the steady state rolling problems, it necessitates an assumption about the unknown shape of the control volume. In almost all cases. the assumed control volume does not match the final shape and the control volume should be updated. This update can be accomplished by performing a free surface correction. The final shape of a material point, which has a spherical shape at the inlet, can be also predicted by integrating a deformation gradient along a stream line. Analyses of three-roll-stand shape rolling is in detail examined.

• International Journal of Fluid Machinery and Systems
• /
• v.9 no.3
• /
• pp.237-244
• /
• 2016

An unsteady three-dimensional simulation based on Reynolds time-averaged governing equation and RNG $k-{\varepsilon}$ turbulence model, was presented for pump-as-turbine, the pressure fluctuation characteristic of hydraulic turbine with guide vane was obtained. The results show that the time domains of pressure fluctuation in volute change periodically and have identical cycles. In volute tongue and inlet pressure fluctuations are light, while in dynamic and static coupling interface pressure fluctuations are serious; In impeller blade region the pressure fluctuation of pressure surface are lighter than that of suction surface. The dominant frequencies of pressure fluctuation concentrate in low frequency region, and concentrate within 2 times of the blade passing frequency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.3
• /
• pp.410-416
• /
• 2002

The fluid flow, heat transfer and the local mass fraction of chemical species in the chemical vapor deposition(CVD) manufacturing process are studied numerically. Flow with a dilute precursor concentration of silane in hydrogen as the carrier gas enters to the reactor and deposits silicon onto the heated surface. The silicon deposition rate using silane is calculated in the horizontal or vertical, axisymmetric reactor. The effects of inlet carrier gas velocity, mass fraction of silane, susceptor angle and rotation of surface on the deposition rate are described.