• Design & Manufacturing
• /
• 제18권2호
• /
• pp.41-50
• /
• 2024

In this study, experimental design methods were used to derive optimal process conditions for improving the thickness uniformity of a 0.40 mm, 3.5 inch light guide panel. Process mapping and expert group analysis were used to identify factors that influence the thickness of injection molded products. The key factors identified were mold temperature, mold temperature, injection speed, packing pressure, packing time, clamp force, and flash time. Considering the resin manufacturer's recommended process conditions and the process conditions for similar light guide plates, a three-level range was selected for the identified influencing factors. L27 orthogonal array process conditions were generated using the Taguchi method. Injection molding was performed using these L27 orthogonal array to mold the 3.5 inch light guide plates. Thickness measurements were then taken, and the results were analyzed using the signal-to-noise ratio to maximize the CpK value, leading to the determination of the optimal process conditions. The thickness uniformity of the product was analyzed by applying the derived optimum process conditions. The results showed a 97.5% improvement in the Cpk value of 3.22 compared to the process conditions used for similar light guide plates.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.22-26
• /
• 2023

As Light-Emitting Diodes(LEDs) continue to advance in performance, their application in automotive lamps is increasing. Automotive LEDs utilize light guides not only for aesthetics but also to control light quantity and direction. Light guides employ patterns of a few hundred micrometers(㎛) to regulate the light, and the surface roughness(Ra) of these patterns can reach tens of nanometers(nm). Given that these light guides are produced through injection molding, mold processing technology with high surface quality micro-patterns is required. This study serves as a preliminary investigation into the development of high surface quality micro-pattern processing technology. It examines the surface roughness of the workpiece based on the cutting direction of the pattern and the cutting fluid type when cutting micro-patterns on STAVAX steel using cubic Boron Nitride(cBN) tools. The experiments involved machining a step-shaped micro-pattern with a height of 60 ㎛ and a pitch of 400 ㎛ in a 22×22 mm area under identical cutting conditions, with only the cutting direction and cutting fluid type being varied. The machining results of four cases were compared, encompassing two cases of cutting direction(parallel to the pattern, orthogonal to the pattern) and two cases of cutting fluid type (flood, mist). Consequently, the Ra value was found to be the highest(Ra 128.33 nm) when machining with the flood type in parallel to the pattern, while it was the lowest(Ra 95.22 nm) when machining with the mist type orthogonal to the pattern. These findings confirm that there is a difference of up to 25.8 % in the Ra value depending on the cutting direction and cutting fluid type.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.43-44
• /
• 2012

본 논문에서는 도로조명용 LED 이차광학계의 제조공정에서 발행하는 형상오차를 설계에 반영하여 제작 후 형상 정밀도를 높여 궁극적으로 도로조명의 조명율을 향상시키는 방법을 제시하였다. 이를 통하여 동일한 에너지를 소모로도 더 높은 광밀도를 가질수 있는 LED2 차렌즈의 제조방법을 제시하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.707-712
• /
• 1991

In machining a part in CAD/CAM system, it is required that the drawing information should be automatically generated, modified, deleted, and thus be used as an general information throughout the entire manufacturing process. This research addresses basic entities(point, line, circle, arc) for design feature and combination of this features, based on GT concepts, with minimum user's manual input. This paper deals with the generalization of operating system which can cover the s parts which appears in mechanical part handbook and the basic constitutional part of sold base. The system developed shows a strong application impact on automatic process planning system of medium - size injection sold companies.

• Design & Manufacturing
• /
• 제6권2호
• /
• pp.64-69
• /
• 2012

This study looks at plastic mold design for robots and mold manufacture, which is an injection mold branch at The Korea-China-Japan University Grand Prize Contest. Product analysis and layout, molding analysis, and upper and lower core design are carried out to design molds in 2D and 3D. After the design of the cores, NC machining software is used for simulation before actual manufacture. Before the production of end-product, test injection is done to troubleshoot problems like bad dimensions, burr, cracks and stepped pulley.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1215-1219
• /
• 2003

Light Guide Panel(LGP) is a key part of backlight unit(BLU) which transforms line-light of lamp to surface-light. Dot pattern is formed on the injected LGP surface by screen printing. This dot pattern is composed of several ten thousands micro dots of diameter 150-180$\mu\textrm{m}$ or so. The dot patterning by screen printing causes low productivity and low performance of TFT-LCD. This research develops the micromachining technology for LGP mould which could form micro dot pattern by injection molding, removing the existing screen printing process.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.793-798
• /
• 2011

In this study, it was grasped to the flow characteristics of cutting fluid injected by nozzle installed in high pressure holder for avoiding chip curling occurred during machining process. And for avoiding chip curling, the possibility of elimination under various chip conditions was checked. Consequently, the highest discharging pressure and velocity was shown in 150 of nozzle inflow angle. Also as nozzle outlet diameter is small, the pressure and velocity of injected flow are high. Moreover, It could be confirmed that width and thickness of chip have no direct effect on chip elimination and it is achieved by torque generated by injected cutting fluid.

• 한국정밀공학회지
• /
• 제20권4호
• /
• pp.118-127
• /
• 2003

An effective tool management system is one of the keys to maximizing the benefits of a computer integrated manufacturing (CIM). Tool management systems, however, are often tailored to the requirement of a highly automated system. Therefore, a different approach is needed for small and medium sized mold shops. This work deals with the implementation of tool management system for milling operations in small and medium sized CIM environment of injection mold production. In this paper, a distributed management approach is proposed for efficient tool management in relatively small machining shops in mold industry. And the design and the functions of the developed system are described.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.370-375
• /
• 2002

Recently, the interest on micro optical parts has increased rapidly with the development of technology related to microsystems. Among the optical parts, micro lens is one of the most broadly used micro parts. To mass-produce the micro lenses, it is very effective to use the mold insert and injection molding process. There are many methods to fabricate the mold insert for micro lenses: electroforming, etching, mechanical micromachining and so on. In this study, we fabricated the mold insert for micro lenses using a micro ball endmill to apply mechanical micromaching method and analyzed the effect of main process parameters such as spindle speed, feed rate, dwell time on the processed surface. Then, using fabricated the mold insert we fabricated the micro lenses through injection molding process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.427-427
• /
• 2007

The global applications of aspherics surfaces will expand rapidly on the electronics, optical components, communications, aerospace, defense, and medical optics devices etc. Especially, Asymmetric aspheric prism lens is one of the important parts in HMD(Head Mounted Display) because it affects dominantly on the optical performance of HMD. The mold core is the most important device to produce the plastic lenses by injection molding method. In this study, the mold cores for asymmetric aspheric prism lens were processed using fly-cutting method which is kind of the ultra precision processing and form accuracy and surface roughness of the cores were measured.