• Journal of the Korean Society of Safety
• /
• v.14 no.3
• /
• pp.25-32
• /
• 1999

This study has been performed to investigate the stress distribution around defects that behave as stress concentrators. Besides, the effect of stress interaction effects on the initiation of primary cracks were also investigated by rotary bending fatigue tests which were performed with specimens drilled micro surface defects and the stress distribution was analyzed using Finite Element Method. In addition, the stress interaction effects around defects and cracks were investigated by comparing the results of experiments and F.E.M. The results obtained are summarized as follows ; 1) Area which slip and micro cracks initiated at micro surface defects is between the maximum shear stress points and this area is over than ${\pm}30^{\circ}$ from the maximum stress point along the defect edge. 2) The stress interaction effect for the small size defect is larger than that of large size defect when the interval between them is near 3) Interval which there is no shear stress interaction effect analyzed by F.E.M. is larger than that of experimental results.

• Journal of Power System Engineering
• /
• v.10 no.3
• /
• pp.38-44
• /
• 2006

Failure assessment of steam generator tube are very important for the integrity of energy plants. In pipes of energy plants, sometimes, the local wall thinning may result from severe erosion-corrosion damage. Recently, the effects of local wall thinning on fracture strength and fracture behavior of piping system have been well studied. In this paper, the elasto-plastic analysis is performed by FE code ANSIS on steam generator tube with wall thinning. We evaluated the failure mode, fracture strength and fracture behavior from FE analysis. It was possible to predict the crack initiation point by estimating true fracture ductility under multi-axial stress conditions at the center of the thinned area.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.139-144
• /
• 2004

Dynamic crack initiation in ductile steel is investigated by means of impact loaded 3 point bend(PB) specimens. Results from non-viscoplastic and viscoplastic materials are compared. Their materials are applied with various impact velocities and static strain rates. The specimen has the size 320${\times}$750 mm with a thickness of 10 mm. A modified 3PB specimen design with reduced width at the ends has been developed in order to avoid the initial compressive load of the crack tip and also to avoid the uncertain boundary conditions at the impact heads. Numerical simulations are made by using the FEM code ABAQUS. Therefore, their results are plotted by shapes of the von Mises plastic stress and equivalent plastic strain of the specimens applied by various impact velocities.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.63-68
• /
• 2008

The fatigue characteristics of bevel gear used for differential gear of automobile was investigated in this paper. From the A-N(Almen intensity-Number of fracture)curve of bevel gear it was shown that there was a specific time that have a maximum fatigue life. Optimal peening condition was 65m/s of project velocity and 8min of project time. Fatigue life was also investigated from the S-N curve between optimal peened specimen and unpeened specimen. Another very significant point is that the crack initiation of bevel gear by shot peening was generated in the subsurface from fractography. This paper shows that shot peening process tremendously improve fatigue characteristics of bevel gear.

• Journal of the Korean Society of Combustion
• /
• v.7 no.1
• /
• pp.58-64
• /
• 2002

The bed combustion in an incinerator interacts with the gas flow region through heat and mass transfer. Combined bed combustion and gas flow simulations are performed to investigate this coupled interaction for various operating conditions and furnace configurations. Radiation onto the bed from the furnace is interrelated with the combustion characteristics in the bed, and is also affected by the flow pattern in the gas flow region. Since the contribution of gaseous emission to the total radiation is significant, an adequate flow pattern in a well-designed furnace shape would lead to an increased heat influx on the bed, especially in the early stage of the waste combustion. Advancing the initiation point of the waste combustion can also reduce the size of the lower gas temperature region above the bed, which can be achieved by controlling operating conditions such as the waste feeding rate, the bed height and the primary air flow distribution.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.665-670
• /
• 1999

The shear behavior and strength of simply supported reinforced concrete deep beams with web opening subject to concentrated loads have been investigated experimentally on the effects of structural parameters such as location of web opening and reinforcements. A total of 12 specimens were tested at the laboratory under two-point top loading. The shear span-to-depth ratio was taken constantly 0.8, and various types of reinforcements based on truss models were adopted. In the tests, the effects of location, reinforcements of web openings on the shear behavior, and crack initiation and propagation have been carefully checked and analyzed. The test results have been compared with the formulas proposed currently being used and analyzed by nonlinear finite element method. Shear strengths obtained from the tests showed good matches with Kong and Ray's equation, and also with the results calculated by nonlinear finite element method.

• The Journal of Internal Korean Medicine
• /
• v.19 no.1
• /
• pp.291-300
• /
• 1998

Dementia is the neurodegenerative process that affects cognition, behavior and function and one of the most prominent diseases of dementia is Alzheimer's disease(AD). AD is a dementing illness characterized clinically by the progressive and irreversible deafferentation of the limbic system, association neocortex and basal forebrain. A number of conditions are known to be predisposing risk factors for AD. In several of these, initiation of glial-mediated inflammatory pathways as a mechanism of AD is getting a lot of attention. On the other hand, a biochemical marker for monitoring the onset and progression of the disease would be a valuable tool for disease management. Also such a marker might be used as an end point in clinical intervention protocols. This biochemical marker will have the potential for identifying subjects afflicted with the disease and possibly for monitoring the onset and longitudinal progression of the disease. Here we have reviewed the latest papers of different approaches to AD. Of course, there is a section of PET which is very useful clinically nowadays.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.3 s.28
• /
• pp.107-116
• /
• 1996

The studies are conducted to investigate the fatigue and fracture, behavior of preflex girder. In this work, the fatigue tests using by constant amplitude fatigue loading and 4-point-loading to maintain pure bending condition in the mid-span of preflex girder will be performed. It is expected from the results of the studies to provide the fatigue strength and the S-N curve of preflex girders. In addition, it will be ensured that fracture initiation occurs in the welded part of horseshoe-type shear connector as well as in other welded joints.

• Journal of Welding and Joining
• /
• v.11 no.1
• /
• pp.42-51
• /
• 1993

In this study, investigations were conducted in calculating parameters of elastic-plastic fracture mechanics using single specimen. The validity of these testing methods was judged by the confirmation of multiple specimen method of stop block test. The results were as follows: In order to measure a fracture toughness using the instrumented impact test, two general requirement must be considered; One, setting up proper impact velocity considered the effect of loading and the other, the necessity of low blow test for obtaining true energy by the compliance correction. It was possible to detect a crack initiation point by calculating the compliance changing rate from a load-defection curve. Criterion of a stable crack growth, $T_{mat}$ could be estimated by using key-curve method for a base metal. and combining Kaiser's rebound compliance with Paris-Hutchison's $T_{appl}$ equation for the brittled zone of welding heat affected.at affected.d.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.25 no.4
• /
• pp.39-46
• /
• 1988

The purpose of this paper is to apply the boundary element method to predict the crack growth path. The quarter point element with traction singularity at the crack tip is applied to compact tension type specimens and two inclined slit problems under compression load. The maximum stress criterion which was originally derived for the crack initiation is extended to the analysis of the crack propagation. The predicted crack paths with 1/4 crack growth increment of initial crack length agree quite well with experimental results. It is found that the computed crack path of the boundary element analysis is not mainly affected by the crack increment length.