• Journal of the Korean Geotechnical Society
• /
• v.34 no.5
• /
• pp.37-51
• /
• 2018

The slope failure due to the rainfall infiltration occurs frequently in Korea, since the depth of the weathered residual soil layer is shallow in mountainous region. Depth of the failure surface is shallow and tends to pass near the interface between impermeable bedrock and soil layer. Soil parameters that have a significant impact on the instability of unsaturated slopes due to rainfall infiltration inevitably include large uncertainties. Therefore, this study proposes a probabilistic analysis procedure by Monte Carlo Simulation which considers the hydraulic characteristics and strength characteristics of soil as random variables in order to predict slope failure due to rainfall infiltration. The Green-Ampt infiltration model was modified to reflect the boundary conditions on the slope surface according to the rainfall intensity and the boundary condition of the shallow impermeable bedrock was introduced to predict the stability of unsaturated soil slope with shallow bedrock under constant rainfall intensity. The results of infiltration analysis were used as inputs of infinite slope analysis to calculate the safety factor. The proposed analysis method can be used to calculate the time-dependent failure probability of soil slope due to rainfall infiltration.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.3
• /
• pp.133-141
• /
• 2011

Urban development of basin causes increasing runoff volume and peak flowrate and shortening in time of concentration, which may cause frequent flooding downstream. An infiltration facilities are operated as a method of reducing flood discharge of urban rivers and peak flowrate. There are various types of infiltration facilities like infiltration trench and porous pavement. In this study, runoff reduction effect due to installation of infiltration facilities are performed and focused on $0.18km^2$ residential area of Ok-kye dong and $0.67km^2$ industrial area of Gong-dan dong in Gumi City. The analysis is fulfilled with comparison of total runoff volume and runoff reduction volume by using the WinSLAMM and the relation equation between area ratio of infiltration facilities and ratio of runoff reduction are derived and peak flow reduction effect for installation of infiltration facilities is analyzed.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.9
• /
• pp.5-22
• /
• 2017

The procedure that combines the result of infiltration analysis into stability analysis based on the limit equilibrium method is widely used to evaluate the impact of rainfall infiltration on slope stability. Accurate prediction of rainfall infiltration is essential to the prediction of landslides caused by rainfall, requires to obtain accurate unsaturated hydraulic properties of the soil. Among the unsaturated hydraulic characteristics of the soil, the importance of the soil-water characteristic curve describing the retained water characteristics of the soil is relatively well known and the measurement by test method to obtain the SWCC is gradually increasing. However, it takes a lot of time and expenses to experimentally measure the unsaturated conductivity characteristics of the soil. Therefore, it is common practice to estimate the hydraulic conductivity function from the SWCC. Although it is widely known that the SWCC has a great influence on rainfall infiltration, studies on the effect of the hydraulic conductivity function estimated from the SWCC on rainfall infiltration are very limited. In this study, we explained how the estimation model of the hydraulic conductivity function affects rainfall infiltration and slope stability analysis. To this end, one-dimensional infiltration analysis and slope stability analysis were conducted by using the data on the SWCC of weathered granite soil widely distributed in Korea. The applicability of each estimation model is discussed through review of the analysis results.

• Laser Solutions
• /
• v.7 no.1
• /
• pp.37-47
• /
• 2004

Laser-assisted selective infiltration is a new method of building metal layers to make metal parts layer by layer, in which superheated microscopic metal droplets are infiltrated into a laser-preheated layer of microscopic metal powders. In this work, the selective infiltration of a low melting-point metal, Sn-37Pb wt%, was conducted to investigate the effects of such dominant parameters as superheating temperature, Nd:YAG laser power for preheating, substrate temperature, etc. The optimal conditions for successful selective infiltration of a single layer of microscopic metal powder were experimentally obtained

• Journal of Korea Water Resources Association
• /
• v.51 no.12
• /
• pp.1237-1245
• /
• 2018

We developed the assessment method for weekly groundwater resources management vulnerability. To consider the effect of precipitation on groundwater level, we calculated correlation coefficient between groundwater level and precipitation applying critical infiltration concept. We developed the vulnerability assessment criteria and calculated weights for criteria using the entropy method. Weekly groundwater resources management vulnerability of small administrative districts were estimated using developed method in this research. The developed method can be a basis for the establishment of the spatio-temporal groundwater resources management plan.

• Journal of the Korean Ceramic Society
• /
• v.29 no.9
• /
• pp.719-728
• /
• 1992

ZrO2/Al2O3-Mullite composites were prepared by infiltration of the silica sol to the porous ZrO2/Al2O3 bodies. The porous ZrO2/Al2O3 bodies for infiltration were fabricated using ZrO2 (20wt%)/Al2O3 composite powders synthesized by the emulsion-hot kerosene drying method. The preparation of silica sols was conducted by the hydrolysis-peptization of an alcoholic TEOS solution. When ZrO2/Al2O3-Mullite and ZrO2/Al2O3 composites were sintered at 1$650^{\circ}C$ for 4 hrs, both of them showed an excellent sinterability. As the amount of mullite added in the composites increased, the ratio of the tetragonal phase of zirconia to the monoclinic phase at the room temperature became higher. It was known that values of the fracture toughness of the ZrO2/Al2O3-Mullite composites were about 5.48 MPa.m1/2 much larger than that of the ZrO2/Al2O3 system.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.735-738
• /
• 2005

The purpose of this study is the infiltration characteristics of soil cut-slope by rainfall. Stability analysis of soil cut-slopes has been conducted by limit equilibrium method on Seep/w and finite element method on Slope/w. Result is same as following. First. the hour when seepage line and groundwater in contact is proportionate from rainfall rate condition and upper natural slope gradient condition which is identical. Second, when seepage line and groundwater is contact, seepage line moves gradually at soil cut-slope surface. Finally, seepage line is formed similarly with soil cut-slope gradient. Third, when rainfall is ended, from the recording upper natural slope where the hour will pass it is stabilized

• Journal of Korean Society of Water and Wastewater
• /
• v.17 no.4
• /
• pp.495-502
• /
• 2003

In order to modify incorrect flow data in the sewage system, the method using the stage-discharge relation and hydraulic characteristic curve of sewer pipe are applied. The modified data were verified with field measured data and the infiltration analysis using the modified data was carried out. When flowrate were measured using the flow-meter in fair weather, the stage data were comparatively consistent but velocity data were very poor for the most part. Therefore, it was recommended that sewage flowrate variation characteristic curve and infiltration were computed using the modified data on the basis of stage data. Especially, in the case of using the hydraulic characteristic curve, extrapolation results of the rainy season flowrate using regression curve on the basis of the data in fair weather were also reasonable.

• Journal of Korea Foundry Society
• /
• v.21 no.3
• /
• pp.163-178
• /
• 2001

The squeeze infiltration process is potentially of considerable industrial importance. The performance enhancements resulting from incorporation of short alumina fiber into aluminum are well documented. These are particularly significant for certain automobile components. Aluminum matrix composite automotive parts, such as diesel engine pistons or engine blocks are produced using squeeze casting apparatus or pressure die-casting apparatus. But the solidification process gets complicated with manufacturing parameters and the factors for porosity formation have not fully understood yet. In this study the formation of porosity during squeeze infiltration has been studied experimentally to achieve an improved understanding of the squeeze infiltration process for manufacture of short-fiber-reinforced components, particularly the mechanism of porosity formation. Al-based MMCs produced under a range of conditions were examined metallographically and the porosity characterised;a kind of matrix, an initial temperature of melt, and a volume fraction of reinforcement. The densimetry and the microscopic image analysis were done to measure the amount of porosity. A correlation between manufacturing parameters and defects was investigated through these.

• Journal of the Korean Ceramic Society
• /
• v.52 no.4
• /
• pp.284-289
• /
• 2015

This study examined carbon layer coating on silicon carbide (SiC) fibers by utilizing solid-state and wet chemistry routes to confer toughness to the fiber-reinforced ceramic matrix composites, as an alternative to the conventional pyrolytic carbon (PyC) interphase layer. Electrophoretic deposition (EPD) of carbon black nanoparticles using both AC and DC current sources, and the vacuum infiltration of phenolic resin followed by pyrolysis were tested. Because of the use of a liquid phase, the vacuum infiltration resulted in more uniform and denser carbon coating than the EPD routes with solid carbon black particles. Thereafter, vacuum infiltration with controlled variation in phenolic resin concentration, as well as the iterations of infiltration steps, was improvised to produce a homogeneous carbon coating having a thickness of several hundred nanometers on the SiC fiber. Conclusively, it was demonstrated that the carbon coating on the SiC fiber could be achieved using a simpler method than the conventional chemical vapor deposition technique.