• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.723-727
• /
• 2004

A new high-performance and low cost single switch energy recovery display driver for an AC plasma display panel (PDP) is proposed. Since it is composed of only one auxiliary power switch, two small inductors, and eight diodes compared with the conventional circuit consisting of four auxiliary power switches, two small inductors, eight power diodes, and two external capacitors, it features a much simpler structure and lower cost. Nevertheless, since the rootmean-square (RMS) value of the inductor current is very small, it also has very desirable advantages such as n low conduction loss and high efficiency. Furthermore, there are no serious voltage-drops caused by the large gas-discharge current with the aid of the discharge current compensation, which can also greatly reduce the current flowing through power switches and maintain the panel to light at n lower sustaining voltage. In addition, all main power switches are turned on under the zero-voltage switching (ZVS) and thus, the proposed circuit has a improved EMI, increased reliability, and high efficiency. Therefore, the proposed circuit will be well suited to the wall hanging PDP TV. To confirm the validity of the proposed circuit, circuit operations, features,and design considerations are presented and verified experimentally on a 6-inch PDP, 50kHz-switching frequency, and sustaining voltage 141V based prototype.

• 한국정보통신설비학회:학술대회논문집
• /
• 2004.08a
• /
• pp.11-14
• /
• 2004

In this paper, a novel tunable bandpass filter using tunable series inductors and MEMS switches for wireless LAN applications was proposed. The proposed tunable filter was fabricated using a micromachining technology and performances of the fabricated filter were estimated. The filter consists of spiral inductors, MIM capacitors and direct-contact type MEMS switches, and its frequency tunability is achieved by changing the inductance that is induced by ON/OFF actuations of the MEMS switches. The actuation voltage of the MEMS switches was 58 V, and the measured center frequencies were 2.55 GHz and 5.1 GHz, respectively. The passband insertion loss and 3-dB bandwidth were 4.2 dB and 22.5 % at 2.55 GHz, and 5.2 dB and 23.5 % at 5.1 GHz, respectively.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.10
• /
• pp.581-586
• /
• 2002

To improve the current waveform of diode rectifiers, we propose a new operating principle for the voltage-doubler diode rectifiers. In the conventional voltage-doubler rectifier circuit, relatively large capacitors are used to boost the output voltage, while the proposed circuit uses smaller ones and a small reactor not to boost the output voltage but improve the input current waveform. A circuit design method is shown by experimentation and confirmed simulation. The experimental results of the proposed diode rectifier satisfies the harmonic guide lines. A high input power factor of 97(%) and an efficiency of 98[%] are also obtained. The new rectifier with no controlled switches meet the harmonic guide lines, resulting in a simple, reliable and low-cost at-to dc converters in comparison with the boost-type current-improving circuits. This paper proposes a nonlinear impedance circuit composed by diodes and inductors or capacitors. This circuit needs no control circuits and switches, and the impedance value is changed by the polarity of current or voltage. And this paper presents one of these applications to improve the input current of capacitor input diode rectifiers. The rectifier using the nonlinear impedance circuit is constructed with four diodes and four capacitors in addition to the conventional rectifiers, that is, it has eight diodes and five capacitors, including a DC link capacitor. It makes harmonic components of the input current reduction and the power factor improvement. Half pulse-width modulated (HPWM) inverter was explained compared with conventional pulse width modulated(PWM) inverter. Proposed HPWM inverter eliminated dead-time by lowering switching loss and holding over-shooting.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.45-45
• /
• 2007

Capacitors among the embedded passive components are most widely studied because they are the major components in terms of size and number and hard to embed compared with resistors and inductors due to the more complicated structure. To fabricate a capacitor-embedded PCB for in-line process, it is essential to adopt a low temperature process (<$200^{\circ}C$). However, high dielectric materials such as ferroelectrics show a low permittivity and a high dielectric loss when they are processed at low temperatures. To solve these contradicting problems, we studied BMN materials as a candidate for dielectric capacitors. processed at PCB-compatible temperatures. The morphologies of BMN thin films were investigated by AFM and SEM equipment. The electric properties (C-F, I-V) of Pt/BMN/Cu/polymer were evaluated using an impedance analysis (HP 4194A) and semiconductor parameter analyzer (HP4156A). $Bi_2Mg_{2/3}Nb_{4/3}O_7$(BMN) thin films deposited on copper clad laminate substrates by sputtering system as a function of Ar/$O_2$ flow rate at room temperature showed smooth surface morphologies having root mean square roughness of approximately 5.0 nm. 200-nm-thick films deposited at RT exhibit a dielectric constant of 40, a capacitance density of approximately $150\;nF/cm^2$, and breakdown voltage above 6 V. The crystallinity of the BMN thin films was studied by TEM and XRD. BMN thin film capacitors are expected to be promising candidates as embedded capacitors for printed circuit board (PCB).

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.436-446
• /
• 2016

A novel step-up DC-DC converter with a switched-coupled-inductor-capacitor (SCIC) which successfully integrates three-winding coupled inductors and switched-capacitor techniques is proposed in this paper. The primary side of the coupled inductors for the SCIC is charged by the input source, and the capacitors are charged in parallel and discharged in series by the secondary windings of the coupled inductor to achieve a high step-up voltage gain with an appropriate duty ratio. In addition, the passive lossless clamped circuits recycle the leakage energy and reduce the voltage stress on the main switch effectively, and the reverse-recovery problem of the diodes is alleviated by the leakage inductor. Thus, the efficiency can be improved. The operating principle and steady-state analyses of the converter are discussed in detail. Finally, a prototype circuit at a 50 kHz switching frequency with a 20-V input voltage, a 200-V output voltage, and a 200-W output power is built in the laboratory to verify the performance of the proposed converter.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1929_1930
• /
• 2009

Fully embedded tunable bandpass filter (BPF) with inductive coupling circuits is newly designed and demonstrated for UHF TV tuner ranged from 500MHz to 900MHz receivers. Conventional RF tuning circuit with an electromagnetic coupled tunable filter has several problems such as large size, high volume, and high cost, since the electromagnetic coupled filter is comprised of several passive components and air core inductors to be assembled and controlled manually. To address these obstacles, compact tunable filter with inductive coupling circuit was embedded into low cost organic package substrate. The embedded filter was optimally designed to have high performance by using high Q spiral stacked inductors, high dielectric $BaTiO_3$ composite MIM capacitors, varactor diodes. It exhibited low insertion loss of approximately -2dB, high return loss of below -10dB, and large tuning range of 56.3%. It has an extremely compact size of $3.4{\times}4.4{\times}0.5mm^3$.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.387-390
• /
• 1998

In this paper, HBT's with lower phase noise and passive elements, such as resistors, capacitors and inductors, for resonance and impedance matching networks are designed, fabricated, tested, and carefully analysed, respectively, and then, they are integrated for the design and fabrication of functional X-band oscillators with lower phase noise. Epi-wafers for HBT's with the structure of graded $Al_{x}$G $a_{1-x}$ As emitter and C-doped base layer of 700.angs. thick were used to specially emphasize the improvement of $f_{T}$ and $f_{max}$, and the lowering of phase noise, in design aspects. At the test frequencies of 12GHz, capacitances of MIM capacitors, spiral inductor, and resistances are 0.5~10pF, 0.4~11.06nH, and 20~1,380.ohm., respectively. The emitter size of HBY's for the X-band MMIC oscillators is 3*10u $m^{2}$, and find chip size is 0.9*0.9m $m^{2}$..EX>.

• ETRI Journal
• /
• v.39 no.5
• /
• pp.756-763
• /
• 2017

A switchable single-wideband (SWB)-to-dual-wideband (DWB) bandpass filter (BPF), which is realized by using lumped switches, is presented in this paper. By alternating the operation modes-ON and OFF-in which the ON mode is achieved by placing the capacitors at the switching spots and the OFF mode is achieved by replacing the capacitors with inductors, DWB-to-SWB BPF can be achieved on the same device. In addition, by changing the capacitor values, the center frequency (CF) of the lower passband of DWB BPF can be easily tuned from 1.69 GHz to 2.22 GHz, while the higher passband stays almost unchanged. As an example, an SWB-to-DWB BPF is designed, fabricated, and measured. This BPF exhibits good performance including wideband, high isolation, compact size, and ability to switch.

• Journal of Power Electronics
• /
• v.17 no.2
• /
• pp.411-421
• /
• 2017

An approach based on a 2D lumped model is presented to quantify the voltage transfer gain (VTG) in power converter low power planes. The advantage of the modeling approach is the ease with which typical noise reduction devices such as decoupling capacitors or ferrite beads can be integrated into the model. This feature is enforced by a new modular approach based on effective matrix partitioning, which is presented in the paper. This partitioning is used to decouple power plane equations from external device impedance, which avoids the need for rewriting of a whole set of equation at every change. The model is quickly solved in the frequency domain, which is well suited for an automated layout optimization algorithm. Using frequency domain modeling also allows the integration of frequency-dependent devices such inductors and capacitors, which are required for realistic computation results. In order to check the precision of the modeling approach, VTGs for several layout configurations are computed and compared with experimental measurements based on scattering parameters.

• Journal of Advanced Navigation Technology
• /
• v.13 no.2
• /
• pp.194-200
• /
• 2009

This paper introduces a ring hybrid coupler using shunt capacitors, high impedance lines and CRLH-TLs (Composite Right/Left-Handed Transmission Lines) with size reduction and bandwidth enhancement. The reduced method of line length uses to combine a short length high impedance line and shunt capacitors. Also, there is combined CRLH meta-material so as to obtain wide bandwidth of transmission line using nonlinear phase characteristic of CRLH-TL that consists of series capacitors and shunt inductors. The implemented ring hybrid coupler shows a novel design with compact size that is smaller than 10% and bandwidth is larger than 60% of conventional ring hybrid coupler.