• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.361-363
• /
• 2007

In this paper, an auto-diagnosis method of rotor bar fault for small induction motor is suggested. Usually FFT of stator currents are given the good results, but to detect the fault, slip is needed for calculating the feature frequency. The slip is varied as the load is changed. So in this paper, some alternative method for estimating the load is suggested. This method is based on the Park's vector pattern. The magnitudes of the feature frequency are compared with the threshhold that is predefined in the bounded range of load. The healthy rotor, single rotor bar fault and double rotor bar fault are tested with no load, 25%, 50%, 75%, and 100% rated load. From 50% to 100% rated load case, the rotor bar faults are detectable using indirect estimation of the load and the comparing the magnitudes of feature frequency. The no load case and under 40% rated load case, rotor fault are un detectable.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.404-405
• /
• 2018

본 논문에서는 유도전동기의 지속적 구동에 의한 파라미터값의 변화에 따른 간접벡터제어의 성능비교에 대한 연구를 하였다. 파라미터 값의 변화에 따라 제어성능이 어떻게 변화하는지를 모의실험을 통해 확인하고자 하였다. 변화는 2.2kW의 정격 출력을 갖는 유도전동기 구동시스템을 통해 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.131-134
• /
• 2001

The accurate identification of the motor parameters is crucially important to achieve high dynamic performance of induction motors. In this paper, the motor parameters such as rotor resistance, stator(rotor) leakage inductance, mutual inductance are measured for torque monitoring and indirect vector control. To demonstrate the practical significance of the results, some experimental results are presented.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.163-165
• /
• 2008

본 논문에서는 유도전동기를 순시 토크제어하기 위한 방법으로 간접벡터제어를 사용하였고, 간접벡터제어를 통해 계산된 전압추종벡터를 NPC형 3-레벨 인버터의 SVPWM기법을 적용하여 구현하였다. SVPWM방식은 기존의 2레벨 인버터의 알고리즘을 응용하여 선형영역에서 과변조영역까지 선형적으로 전이 하도록 하였다.

• Journal of Power Electronics
• /
• v.5 no.1
• /
• pp.20-28
• /
• 2005

This paper presents a fuzzy predictive sliding mode control for high performance induction motor position drives. A new simplified inner-loop sliding-mode current control scheme based on a nonlinear mathematical model of an induction motor is introduced. Novel predictive fuzzy logic PI and PID controllers are used in speed and position loops, respectively. Sliding-mode current controllers and fuzzy predictive logic controllers are designed based on indirect vector control. The overall system performance is examined under different dynamic operating conditions. The performance of the drive system is robust and stable, and insensitive to parameters and operating condition variations even though non-exact system parameters are used in the implementation of the proposed controllers.

• Journal of Power Electronics
• /
• v.12 no.2
• /
• pp.305-316
• /
• 2012

The paper presents an accurate loss model based controller of an induction motor to calculate the optimal air gap flux. The model includes copper losses, iron losses, harmonic losses, friction and windage losses, and stray losses. These losses are represented as a function of the air gap flux. By using the calculated optimal air gap flux compared with rated flux for speed sensorless indirect vector controlled induction motor, an improvement in motor efficiency is achieved. The motor speed performance is improved using a fuzzy logic speed controller instead of a PI controller. The fuzzy logic speed controller was simulated using the fuzzy control interface block of MATLAB/SIMULINK program. The control algorithm is experimentally tested within a PC under RTAI-Linux. The simulation and experimental results show the improvement in motor efficiency and speed performance.

• Journal of Power Electronics
• /
• v.15 no.3
• /
• pp.796-805
• /
• 2015

New direct and indirect current control methods for a fault-tolerant active power filter topology are presented in this paper. Since a three-phase four-switch topology has a phase bridge current which cannot be directly controlled, a hysteresis control method in the α-β plane which controls the three-phase current in the two-phase stationary coordinate system is proposed. The improved SVPWM algorithm is able to eliminate the operation of the trigonometric functions in the traditional algorithm by rotating the α-β coordinates and alternating the sequence of the output vectors, which in turn simplifies the algorithm and reduces the switching frequency. The selection of the DC-side reference voltage and DC-side capacitor equalization strategy are also discussed. Simulation and experiments demonstrate that the proposed control method is correct and feasible.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.404-408
• /
• 2001

This paper deals with speed control of induction motors with a gain tuning based on simple Genetic Algorithms, which are search algorithms based on the mechanics of natual selection and genetics. Based on the designed control system structure, the indirect vector control system of induction motors is simulated. The simulation results show that the system has a strong robust to the parameter variation and is insensitive to the load disturbance. Thus, the proposed PI controller based on genetic algorithms is superior to manually tuned classical PI controller in improving the speed control performance of induction motors.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.3
• /
• pp.238-244
• /
• 2004

To monitor the torque of an induction motor using current, the accurate identification of the motor parameters is very important. In this study, the motor parameters such as rotor resistance, stator and rotor leakage inductance, mutual inductance are estimated for torque monitoring and indirect vector control. Estimated parameters are used to monitor the torque of vector controlled induction motor without any speed measuring sensor. Stator current is measured to estimate the magnetizing current which is used to calculate flux linkage, rotor velocity and motor torque. From the experiments, the proposed method shows a good estimation of the motor parameters and torque under the normal rotational speed.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.417-420
• /
• 2000

In order to the torque control the indirect flux control was performed by controlling the ratio of e/f and the q-axis flux was estimated by the slip command and q-axis flux was estimated by the slip command and q-axis current in the rotor circuits. Also the frequency was controlled to keep on the q-axis flux to be zero and the constant torque characteristics could be obtained by generation the preset torque. In the induction motor driven by the boltage source inverter with the constant voltage and frequency the speed variation is expressed as a slip So the speed control can be achieved by slip compensation The slip was calculated with a q-flux current filtered by first-order filter and as the result the error problem which may occur in current detection was eliminated