• Advances in materials Research
• /
• v.13 no.1
• /
• pp.19-35
• /
• 2024

Presented Article evaluates the effect of nanoclay on permeability, compressive strength, and plasticity behavior of fine-grained soil related to the Tabriz landfill site. In this regard, comprehensive experimental study was performed on taken soil samples (42 specimens) with aim of design high-performance liners for Tabriz landfill. The samples was mixed by 0% (control) 3%, 6% and 9% nanoclay and prepared in 1, 7, 14 and 28 days before testing stage. Index tests like particle-size, permeability, atterberg limits, and uniaxial compressive strength (UCS) was conducted on samples. The results show that studied soil is classified as CL in USCS classification and atterberg limits measured as LL is 37, PL is 20.67, and PI is 16.33 which increase into 75, 45, and 30. The assessment presented the LL was increased about 20.27% based on increasing in nanoclay from 0% to 9%. These variations for PL and PI were 21.77% and 18.37%, respectively. Also, the and soil's compressive strength is increase from 120 kPa to 188 kPa and permeability is estimated as 4.25×10^-6 m/s which reduced into the 6.34×10^-9 m/s with respect the naboclay content increases form 0% to 9%.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.1
• /
• pp.5-12
• /
• 2016

Investigation of in-situ ground in cold region is difficult due to low accessibility and environmental factors. In this study, correlation between dynamic cone resistance and shear strength is suggested to estimate the strength of frozen soils by using instrumented dynamic cone penetrometer. Tests were conducted in freezing chamber after preparing sand-silt mixture with 2.3% water content. Vertical stresses of 5 kPa and 10 kPa were applied during freezing, shearing, and penetration phase to compare the dynamic cone resistance and shear strength. The dynamic cone resistance, additionally, is calculated to minimize the effect of energy loss during hammer impact. Experimental results show that as the shear strength increases, the dynamic cone penetration index (DCPI) decreases nonlinearly, while the dynamic cone resistance increases linearly. This study provides the useful correlation to evaluate strength properties of the frozen soils from the dynamic cone penetration and direct shear tests.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.2
• /
• pp.181-194
• /
• 1999

Both the chemical components and the physical and mechanical properties of the compacted and undisturbed weathered granite soils were estimated to investigate the influences of the degree of weathering and saturation on the shear strength. The weathered granite soils used in this study were taken from six different sites in Korea. The results showed that the shear strength of weathered granite soil decreased with increasing the degree of weathering and saturation. Under the normal stresses less that 40kPa, the shape of Mohr-Coulomb failure envelope followed curved or hyperbolic relationship and a half of cohesion value obtained by the common shear test was observed. Using the Sueoka's method, the values of CWI were ranged from 21.5 to 31.26 which can be characterized as a completely weathered granite soil. Large decrease in shear strength and remarkable variation in dilatancy were observed in saturated granite soil compared to unsaturated soil. It was also found that the shear strength of undisturbed weathered granite soil of Pungam site can be expressed approximately by the equation of ${(\tau)_{sat}= 1.0(\tau)_{unsat}-12.48}$ and this equation can be extended to the other sites considered in this study.

• Geomechanics and Engineering
• /
• v.33 no.1
• /
• pp.1-9
• /
• 2023

The unconfined compression strength (UCS) of soils is commonly used either before or during the construction of geo-structures. In the pre-design stage, UCS as a mechanical property is obtained through a laboratory test that requires cumbersome procedures and high costs from in-situ sampling and sample preparation. As an alternative way, the empirical model established from limited testing cases is used to economically estimate the UCS. However, many parameters affecting the 1D soil compression response hinder employing the traditional statistical analysis. In this study, gene expression programming (GEP) is adopted to develop a prediction model of UCS with common affecting soil properties. A total of 79 undisturbed soil samples are collected, of which 54 samples are utilized for the generation of a predictive model and 25 samples are used to validate the proposed model. Experimental studies are conducted to measure the unconfined compression strength and basic soil index properties. A performance assessment of the prediction model is carried out using statistical checks including the correlation coefficient (R), the root mean square error (RMSE), the mean absolute error (MAE), the relatively squared error (RSE), and external criteria checks. The prediction model has achieved excellent accuracy with values of R, RMSE, MAE, and RSE of 0.98, 10.01, 7.94, and 0.03, respectively for the training data and 0.92, 19.82, 14.56, and 0.15, respectively for the testing data. From the sensitivity analysis and parametric study, the liquid limit and fine content are found to be the most sensitive parameters whereas the sand content is the least critical parameter.

• The Journal of Engineering Geology
• /
• v.19 no.2
• /
• pp.177-189
• /
• 2009

The shear strength has been managed as an important factor in soil mechanics. The shear strength estimation model was developed to evaluate the shear strength using only a few soil properties by the linear regression analysis model which is one of the statistical methods. The shear strength is divided into two part; one is the internal friction angle (${\phi}$) and the other is the cohesion (c). Therefore, some valid soil factors among the results of soil tests are selected through the correlation analysis using SPSS and then the model are formulated by the linear regression analysis based on the relationship between factors. Also, the developed model is compared with the result of direct shear test to prove the rationality of model. As the results of analysis about relationship between soil properties and shear strength, the internal friction angle is highly influenced by the void ratio and the dry unit weight and the cohesion is mainly influenced by the void ratio, the dry unit weight and the plastic index. Meanwhile, the shear strength estimated by the developed model is similar with that of the direct shear test. Therefore, the developed model may be used to estimate the shear strength of soils in the same condition of study area.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.1
• /
• pp.21-28
• /
• 2013

This study proposed optimum lime contents for clayey soils consisting of representative clay minerals, Kaolinite and Na-Bentonite, according to optimum lime content method (ASTM C 977-22) by means of ground improvement method of clayey soils. As geotechnical properties, the variations of atterberg limits and unconfined compressive strength were analyzed and Ca-ion and micro-structure along elapsed time were observed for lime-added clayey specimens. The test results show that optimum lime content method provides an appropriate methodology for ground improvement of clayey soils and the variation of $Ca^{2+}$ might be a good index to predict the rate of ground improvement for clayey soils with lime addition.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.6
• /
• pp.271-276
• /
• 2008

The civil engineering properties for the coal fly ash produced from a power plant mixed with sintered powders made from the fly ash-clay slip system were measured and its applicability for the foundation soils was investigated. The F-slip whose dispersion state is 'not good' and C-slip which is re-flocculated by adding a flocculant to a well-dispersed slip were fabricated and then sintered. The sintered body made from C-slip had more uniform microstructure than that of F-slip, therefore, the bulk density and compressive strength were improved. The civil engineering properties such as compression index, compressive strength, permeability coefficient of fly ash were improved by mixing $0.84{\sim}2\;mm$ powders obtained by crushing a sintered body made from C-slip. Therefore, the applicability of mixed powders composing of fly ash and sintered body made from C-slip was confirmed to foundation soils due to its improved civil engineering properties.

• Geomechanics and Engineering
• /
• v.8 no.2
• /
• pp.173-186
• /
• 2015

The rapid urbanization in Pakistan is creating a shortage of sustainable construction sites with good soil conditions. Attempts have been made to use rice husk ash (RHA) in concrete industry of Pakistan, however, limited literature is available on its potential to improve local soils. This paper presents an experimental study on engineering properties of low and high plastic cohesive soils blended with 0-20% RHA by dry weight of soil. The decrease in plasticity index and shrinkage ratio indicates a reduction in swell potential of RHA treated cohesive soils which is beneficial for problems related to placing pavements and footings on such soils. It is also observed that the increased formation of pozzolanic products within the pore spaces of soil from physicochemical changes transforms RHA treated soils to a compact mass which decreases both total settlement and rate of settlement. A notable increase in friction angle with increase in RHA up to 16% was also observed in direct shear tests. It is concluded that RHA treatment is a cost-effective and sustainable alternate to deal with problematic local cohesive soils in agro-based developing countries like Pakistan.

• Geomechanics and Engineering
• /
• v.8 no.5
• /
• pp.649-661
• /
• 2015

This research provides insight on the laboratory investigation of the engineering properties of a lateritic soil modified with the mucilage of Opuntia ficus-indica cladodes (MOFIC), which has a history of being used as an earthen plaster. The soil is classified, according to AASHTO classification system, as A-2-6(1). The Atterberg limits, compaction, permeability, California bearing ratio (CBR) and unconfined compressive strength of the soil were determined for each of 0, 4, 8 and 12% addition of the MOFIC, by dry weight of the soil. The plasticity index, optimum moisture content, swell potential, unconfined compressive strength and permeability decreased while the soaked and unsoaked CBR increased, with increasing MOFIC contents. The engineering properties of the natural soil, which only satisfies standard requirements for use as subgrade material, became improved by the application of MOFIC such that it meets the standard requirements for use as sub-base material for road construction. The effects of MOFIC on the engineering properties of the soil resulted from bioclogging and biocementation processes. MOFIC is recommended for use as a modifier of the engineering properties of soils, especially those with similar characteristics to that of the soil used in this study, to be used as a pavement layer material. It is more economical and environment-friendly than conventional soil stabilizers or modifiers.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.10
• /
• pp.67-74
• /
• 2013

The objective of this study was to identify the effect of engineering properties on the resilient modulus ($M_r$) of cohesive soils as subgrade. Eight representative cohesive soils representing A-6, and A-7-6 soil types collected from road construction sites, were tested in the laboratory to determine their basic engineering properties. The laboratory tests for the engineering properties were Atterberg limits test, sieve analysis, hydrometer test, Standard Proctor compaction test, and unconfined compressive strength test. Resilient modulus test and unconfined compressive strength test were conducted on unsaturated cohesive soils at three different moisture contents (dry of optimum moisture content, optimum moisture content, and wet of optimum moisture content). The increase in moisture content considerably affected the decrease in the resilient modulus. The resilient modulus increased with an increase in maximum unconfined compressive strength, percent of clay, percent of silt and clay, liquid limit and plasticity index. The resilient modulus decreased with an increase in percent of sand.