• Earthquakes and Structures
• /
• 제19권5호
• /
• pp.331-345
• /
• 2020

The multi-story timber structure with high platform base is one of the important architectural types in the traditional Chinese buildings. To study the dynamic characteristics and seismic responses on this kind of traditional structure, the 3-D finite element models of Xi'an drum tower which included the high platform base, upper timber structure and whole structure was established considering the structural form and material performance parameters of the structure in this study. By the modal analysis, the main frequencies and mode shapes of this kind of traditional building were obtained and investigated. The three kinds of earthquake excitations included El-Centro wave, Taft wave and Lanzhou wave were separately imposed on the upper timber structure model and the overall structure model, and the seismic responses on the tops of columns were analyzed. The results of time history analysis show that the seismic response of the upper timber structure is obviously amplified by high platform base. After considering the effect of high platform base, the mean value on the lateral displacement increments of the top column in the overall structure is more than 20.478% and the increase of dynamic coefficients was all above 0.818 under the above three different earthquake excitations. Obviously, it shows that the existence of high platform base has a negative influence on the seismic responses of upper timber structure. And the high platform base will directly affect the safety of the upper timber structure. Therefore, the influence of high platform base on the dynamic response of its upper timber structure cannot be neglected.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• 제10권3호
• /
• pp.107-113
• /
• 1990

A series of cubical triaxial tests with independent control of the three principal stresses were performed on a compressible sand. All specimens which were formed by depositing the fine sand loosely, were used. It was found that slope of the stress-strain curve increased with increased b value, and the major principal strain at failure first remains approximetely constant for b values smaller than about 0.3 for drained condition and 0.6 for undrained condition respectively, and thereafter decreases with increasing value of b. The test results showed that the direction of the strain increments at failure form acute angles with the failure surfaces for both the drained and undrained condition. The results are thus not in agreement with the normality criterion from classic plasticity theory. However, it was found that the projections of the plastic strain increment vectors on the octahedral plane are perpendicular to the faiure surface in that plane.

• Asian-Australasian Journal of Animal Sciences
• /
• 제29권4호
• /
• pp.464-470
• /
• 2016

The objective of this study was to investigate the accuracy of imputation from low density (LDC) to moderate density SNP chips (MDC) in a Thai Holstein-Other multibreed dairy cattle population. Dairy cattle with complete pedigree information (n = 1,244) from 145 dairy farms were genotyped with GeneSeek GGP20K (n = 570), GGP26K (n = 540) and GGP80K (n = 134) chips. After checking for single nucleotide polymorphism (SNP) quality, 17,779 SNP markers in common between the GGP20K, GGP26K, and GGP80K were used to represent MDC. Animals were divided into two groups, a reference group (n = 912) and a test group (n = 332). The SNP markers chosen for the test group were those located in positions corresponding to GeneSeek GGP9K (n = 7,652). The LDC to MDC genotype imputation was carried out using three different software packages, namely Beagle 3.3 (population-based algorithm), FImpute 2.2 (combined family- and population-based algorithms) and Findhap 4 (combined family- and population-based algorithms). Imputation accuracies within and across chromosomes were calculated as ratios of correctly imputed SNP markers to overall imputed SNP markers. Imputation accuracy for the three software packages ranged from 76.79% to 93.94%. FImpute had higher imputation accuracy (93.94%) than Findhap (84.64%) and Beagle (76.79%). Imputation accuracies were similar and consistent across chromosomes for FImpute, but not for Findhap and Beagle. Most chromosomes that showed either high (73%) or low (80%) imputation accuracies were the same chromosomes that had above and below average linkage disequilibrium (LD; defined here as the correlation between pairs of adjacent SNP within chromosomes less than or equal to 1 Mb apart). Results indicated that FImpute was more suitable than Findhap and Beagle for genotype imputation in this Thai multibreed population. Perhaps additional increments in imputation accuracy could be achieved by increasing the completeness of pedigree information.

• Journal of Korean Neurosurgical Society
• /
• 제57권3호
• /
• pp.185-191
• /
• 2015

Objective : In order to provide normal values of the pediatric sub-axial cervical spinal canal and vertebral body growth pattern using computed tomographic scans, a total of 318 patients less than 10 years old were included. Methods : The growth of the vertebral body and canal space was investigated using four different age groups. The Torg ratio (TR) was calculated and all patients were classified into a low TR group and a high TR group according to a cutoff value of 1.0. To account for spinal curvature, the C3-7 angle was measured. Results : Very little axial expansion and growth in height were observed (2.9 mm and 3.4 mm, respectively), and the spinal canal increments (1.8 mm) were much smaller than the dimensions of the vertebral body. The mean TR values were $1.03{\pm}0.14$ at the C3 vertebral level, $1.02{\pm}0.13$ at C4, $1.05{\pm}0.13$ at C5, $1.04{\pm}0.13$ at C6, and $1.02{\pm}0.12$ at C7 in all patients. The mean sub-axial angle (C3-7) was $7.9{\pm}10.6^{\circ}$ (range: $-17-47^{\circ}$). Conclusion : The upper sub-axial spinal canal continuously increased in size compared to the lower sub-axial spine after 8 years of age. Considerable decrements in the TR was found after late childhood compared to younger ages. Generally, there were no significant differences between boys and girls in vertical length of the cervical vertebrae. However, the axial dimension of the vertebral body and the spinal canal space varied according to gender.

• The Journal of the Acoustical Society of Korea
• /
• 제37권5호
• /
• pp.343-348
• /
• 2018

This paper proposes a simple procedure for estimating the acoustical parameter values in an occupied classroom from measurements in the unoccupied classroom. The total sound absorption in an unoccupied classroom can be calculated from measured reverberation times in the room. The expected occupied absorption can be calculated using equation that was obtained in a previous study (Choi, 2016) by fitting a linear regression line to a plot of total occupied absorption versus the corresponding unoccupied total absorption values measured in 12 university classrooms. The ratios of occupied-to-unoccupied sound absorption are used to predict increments in the values of acoustical parameters when occupants are added to the rooms. Occupied values of acoustical parameters can be estimated from unoccupied values and the change in total room absorption due to adding occupants.

• Journal of Nutrition and Health
• /
• 제31권6호
• /
• pp.1057-1065
• /
• 1998

Anthropometric and body compositional changes and the outcomes of the pregnancies of 90 healthy Korean women were investigated in a longitudinal study. Their weight increased from 51.3$\pm$5.9kg to 65.1$\pm$7.8kg during their pregnancies. The total weight gain was 13.8$\pm$4.5kg, and therefore, weekly weight gain was 340$\pm$110g during the entire period of the pregnancy. The weight gain was composed of approximately 50-60% fat mass and 40-50% fat-free mass. Skinfold thicknesses, both of triceps and subscapular, increased during the pregnancies. The fat mass calculated from skinfold thickness and that measured with bioelectrical impedance analysis went on increasing during the pregnancies. Although there was a considerable difference with respect to the fat mass observed using the three methods, fat mass gain was 5.0-6.1kg and fat-free mass gain was 4.0-5.3kg from the first trimester to the third trimester of pregnancies. There were significant correlations between maternal anthropometric parameters and indices of pregnancy outcomes. Especially, the infant's birth weight was associated with maternal pre-pregnancy weight and weight gains during the pregnancies. The infant's birth length was related to the maternal weight observed at term(p<0.05) and weight gain during the entire pregnancies (p<0.05) . Neither increase of fat mass nor fat-free mass affected the outcomes of pregnancy. These results show that maternal weight gain during pregnancy is led by increments of approximately above 50% fat mass. The fat mass increase seems to be larger in central areas than in subcutaneous areas. Maternal weight gain during pregnancy, especially during late pregnancy, is a factor affecting the birth weight and length of infant. On the basis of the body compositional changes, it can be predicted that the additional energy requirement for pregnancy in Korean women is more than 200-230 MJ (64,500-76,250kca1). (Korean J Nutrition 31(6) : 1057-1065, 1998)

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 한국방송공학회 2009년도 IWAIT
• /
• pp.321-325
• /
• 2009

Sub-pel level motion estimation contributes to significant increase in R-D performance for H.264|MPEG 4 Part 10 AVC. However, several supplements, such as interpolation, block matching, and Hadamard transform which entails large computational complexity of encoding process, are essential to find best matching block in sub-pel level motion estimation and compensation. In this paper, a fast motion estimation scheme in sub-pel accuracy is proposed based on a parabolic model of SAD to avoid such computational complexity. In the proposed scheme, motion estimation (ME) is only performed in integer-pel levels and the following sub-pel level motion vectors are found from the parametric SAD model for which the model parameters are estimated from the SAD values obtained in the integer-pel levels. Fall-back check is performed to ensure the validity of the parabolic SAD model with the estimated parameters. The experiment result shows that the proposed scheme can reduce the motion estimation time up to about 30% of the total ME times in average with negligible amount of PSNR drops (0.14dB in maximum) and bit increments (2.54%in maximum).

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제15권4호
• /
• pp.73-82
• /
• 2016

Recently, automobile industries have been developing many structural automotive parts made of thin, high-strength steel strips to produce safer and more environmentally friendly cars. The roll forming process has been considered one of the most efficient processes in manufacturing high-strength steel parts because it is a high-speed process that forms sheets in increments. However, most automotive parts vary longitudinally in their cross-sections. Therefore, it is difficult to apply the roll forming process to automotive parts made of high-strength steel. A variable section roll forming process has been proposed in recent studies. The rotational axes of the forming rolls are fixed, and the forming rolls have three-dimensional shape. As such, the cross-section of the part varies linearly along its length, and the angle between the bend line and longitudinal axis is less than 1 degree. Thus, the rate of cross-sectional variation along the length is relatively small. In this study, the rate of cross-sectional change along the length of a forming roll has been increased. Moreover, the angle between the bend line and longitudinal axis has been increased up to 15 degrees. The variable sections of the forming rolls have been designed for high strength steel parts with a symmetric u-type cross-section that varies linearly and symmetrically along the longitudinal axis.

• Korean Journal of Materials Research
• /
• 제5권7호
• /
• pp.820-828
• /
• 1995

Ti-sillcides are formed on an atomically clean Si substrate and its phase transition and surface and interface morphologies are examined depending on the Ti-film thicknesses, deposition temperatures and Si substrate orientations. Ti film thicknesses of 400$\AA$ and 200$\AA$ have been deposited at elevated temperatures from 50$0^{\circ}C$ to 90$0^{\circ}C$ with increments of 10$0^{\circ}C$ on Si(100) and Si(111) Ti-silicides are formed and analyzed with using XRD, SEM, and TEM to verify the phase transition and the surface and interface morphologies. The phase transition from C49 to C54 is observed to occur around $650^{\circ}C$ and examined to show some retardation depending on the substrate orientation and film thickness. This retardation of phase transition is explained by the consideration based on the surface and volume free energies. A rough surface of C49 TiSi$_2$is exhibited because of characteristics of nonuniform diffusion across the interface while the smooth surface and island formation of C54 TiSi$_2$is examined.

• Restorative Dentistry and Endodontics
• /
• 제20권1호
• /
• pp.214-234
• /
• 1995

The purpose of this work was to study the compatibility of several commercially available dentin adhesives with composite resins. In this study, V-shaped cavity preparations were created on both buccal and lingual surfaces of 60 extracted human premolars($3mm{\times}3mm{\times}2mm$ deep). Preparations were located such that the occlusal margins were on the enamel and the gingival margins were on the cementum(1mm below the CEJ). These specimens were randomly divided into three equal groups. Three dentin adhesives(Scotchbond Multi-Purpose, All Bond 2, Prisma Universal Bond 3)were applied to the cavity in accordance with each manufacturer's instructions. The teeth in each group were restored with four composite resins(Silux plus, Z100, Bisfil, Prisma TPH) in three increments, with each increment light-cured for 40 seconds. All specimens were exposed to 500 cycles of thermal stress. Specimens then placed in a silver nitrate solution(50% by weight) and stored in darkness for 24 hours. They were then immersed for 6 hours in photographic developing solution under flourescent light. Specimens were sectioned buccolingually through the center of the restoration and observed under a binocular stereoscope. To compare the marginal leakage, ANOVA and Dunkan's multiple range tests were used in analysis. Selected samples were further studied using scanning electron microscopy(XL20, Philips, The Netherlands). The results were as follows. 1. In all groups, the enamel margin showed significantly less leakage than the cementum margin. 2. No statistically significant differences were found in microleakage when composite resins were used with their proprietary dentin adhesives. 3. In comparison between dentin adhesives, Prisma Universal Bond 3 showed significantly less leakage at the enamel margin and Scotch bond multi-purpose showed significantly less leakage at the cementum margin than the other groups. 4. In comparison between composite resins, Silux Plus showed significantly more leakage than other groups at the enamel margin and no statistically significant differences were found in microleakage at the cementum margin. 5. According to the backscattered scanning electron microscope, microleakage occurred via gaps at the dentin adhesives/dentin interface.