• Bulletin of the Korean Chemical Society
• /
• 제8권3호
• /
• pp.133-137
• /
• 1987

Polysiloxane SE-54 liquid phase was immobilized on the support surface as coated in thin film via in-situ cross-linking. The cross-linking between liquid molecules was initiated by dicumylperoxide. Among the supports investigated, only Chromosorb W provided the cross-linkable surface. The optimal in-situ cross-linking was achieved when Chromosorb W was coated with 5% (w/w) SE-54 and cross-linked with 1% (w/w) dicumylperoxide. The cross-linked support was useful for the trace analysis as well as for the trace enrichment.

• Korean Membrane Journal
• /
• 제10권1호
• /
• pp.13-19
• /
• 2008

Water softening is a very promising field for membranes and especially ultra low pressure membranes. Nanofiltration membranes based on pore-filling technology was prepared by using a new technique: the in-situ cross-linking. This route involves introducing a pre-formed polymer into the pores of a host membrane and then locking the polymer in the pores by in-situ cross-linking with an appropriate reagent. By this way, it is possible to make robust and competitive, pore-filled, anion-exchange membranes with excellent control over the properties of the incorporated gel without affecting the host membrane. In this paper, the possibilities of tuning such membranes for ultra low pressure water softening was examined by altering pore-filling chemistry (by changing cross-linking and aminating reagents). The results showed that tuning the chemistry of the pore-filling has important effects. In particularly, it had been shown that the correct selection of cross-linking reagent was not only essential to get pore-filled membranes but it could control their properties. Moreover, the aminating reagent could improve membrane performance. It was found that an increase in hydrophobicity could improve the Darcy permeability.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2001년도 추계 총회 및 학술발표회(한국막학회)
• /
• pp.46-50
• /
• 2001

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.271-271
• /
• 2006

The present article describes a novel method of preparing the sulfonated polysulfone-based PEMs for DMFC, which are excellent in film quality, proton conductivity, methanol impermeability and mechanical properties. No depression in film quality or difficulty in film preparation is observed, even though sulfonated group of the PEMs are kept as high as 70 mol %. Allyl-terminated cooligo-PESs containing the organic sulfonate groups were solvent-cast into films and then thermally treated for cross-linking. Cross-linked sulfonated polysulfone-based PEMs gave unprecedented reduction of methanol cross-over and high ionic conductivity through in-situ thermal polymerization and cross-linking of telechelic sulfonated sulfone oligomers during a membrane preparation.

• 멤브레인
• /
• 제11권3호
• /
• pp.109-115
• /
• 2001

Polypropylene(PP)을 지지막으로 하여 in-situ 가교결합(cross-linking)방식을 이용한 pore-filled 이온교환막을 제조하였다. 다공성 PP막의 기공에 poly(vinylbenzyl chloride)(PVBCI)과 piperazine(PIP), 또는 1,4-diaminobicyclo [2,2,2]octane(DABCO)을 dimethylforamid(DMF)에 녹인 용액을 채워서 겔화시킨 후, 남아있는 chloromethyl 그룹에 trimethylamine을 이용하여 양이온인 암모니움 site를 형성시키면 pore-filled 음이온교환막이 형성된다. 이와 같은 2단계의 제조방식으로 제조된 pore-filled 분리막은 크기의 변화가 없이 안정되며, PVBCI의 농도와 가교제의 농도로써 고분자-겔의 함량(mass gain, MG)과 가교도가 간단하게 조절되는 것을 보여주었다. 특히 아주 낮은 압력(100 kPa)에서의 높은 수투과도(7.9kg/$m^2$hr, 지지막은 PP3, 73%의 MG, 10%의 가교도, PIP 가교제사용)는 연수용 분리막으로 충분히 활용될 수 있음을 보여준다.

• Bulletin of the Korean Chemical Society
• /
• 제18권12호
• /
• pp.1291-1295
• /
• 1997

The catalytic dehydrocoupling of di-n-butylstannane n-Bu2SnH2 by the Cp2MCl2/Red-Al (M = Ti, Zr, Hf) and M(CO)6/Red-Al in situ combination catalysts yielded a mixture of two kinds of catenated products: one is a cross-linked insoluble solid, and the other is a non-cross-linked soluble solid (≒Sn5) or viscous oil (≒Sn2). The soluble oligostannanes could be produced by simple dehydrocoupling of n-Bu2SnH2, whereas the insoluble polystannanes could be obtained via disproportionation/dehydrocoupling combination process of n-Bu2SnH2. The disproportionation/dehydrocoupling combination process may initially produce a low-molecular-weight oligostannane with partial backbone Sn-H bonds which could then undergo an extensive cross-linking reaction of backbone Sn-H bonds, resulting in the formation of an insoluble polystannane.

• Bulletin of the Korean Chemical Society
• /
• 제16권11호
• /
• pp.1109-1112
• /
• 1995

Bis(silyl)alkylbenzenes such as bis(1-sila-sec-butyl)benzene (1) and 2-phenyl-1,3-disilapropane (2) were prepared in high yields by reduction of the corresponding chlorosilanes with LiAlH4. The dehydropolymerization of 1 and 2 was carried out with group 4 metallocene complexes generated in situ from Cp2MCl2/Red-Al and Cp2MCl2/n-BuLi (M=Ti, Hf), producing two phases of polymers. The TGA residue yields of the insoluble polymers were in the range of 64-74%. The molecular weights of the soluble polymers produced ranged from 700 to 5000 (Mw vs polystyrene) and from 500 to 900 (Mn vs polystyrene). The dehydropolymerization of 1 and 2 seemed to initially produce a low-molecular-weight polymer, which then underwent an extensive cross-linking reaction of backbone Si-H bonds, leading to an insoluble polymer.

• 전기화학회지
• /
• 제13권2호
• /
• pp.145-152
• /
• 2010

본 연구에서는 organophosphate를 기반으로 한 과불소화된 아크릴레이트 가교제를 사용하여 제조한겔 고분자 전해질의 이온 전도도 및 전기화학적 특성을 평가하였다. 과불소화된 아크릴레이트 가교제를 사용하여 만든 겔 고분자 전해질은 액체전해질의 함량이 최대 97 wt%까지 안정한 겔 상태를 유지하였다. 본 연구에서 제조한 겔 고분자 전해질의 이온전도도는 $30^{\circ}C$에서 $1.0\;{\times}\;10^{-2}\;S/cm$의 값을 가졌다. 또한 전기화학적 안정성 테스트에서도 약 4.5V로 이상까지 산화에 의한 열화가 없이 안정하였다. 합성된 겔고분자 전해질을 리튬이온 고분자 전지에 적용하여 그 활용성을 평가하였다. 양극으로는 $LiCoO_2$를 사용하였으며 음극으로는 카본을 사용하였다. 이렇게 만든 리튬이온 고분자 전지는 0.1C에서 136.11 mAh/g의 용량으로 이론용량과 거의 비슷한 값을 나타내었으며, 2C 방전에서도 초기 용량의 91%를 유지하였다. 또한 500번의 충방전 후에도 초기 용량의 70%정도의 용량을 유지하였다.

• 대한화장품학회:학술대회논문집
• /
• 대한화장품학회 2003년도 IFSCC Conference Proceeding Book I
• /
• pp.232-257
• /
• 2003

It has been shown that transparent microemulsion gels of flexibly adjustable viscosity containing less than 10％ w/w surfactants can be obtained just by cooling down through a new 1-step preparation procedure (via 4 different in-situ colloidal systems) using PIT-technology with a range of emulsifiers, co-emulsifiers and lipids. They can be used for a wide scope of applications. Specific examples have been given with antiperspirant formulas that proof the stability of these thickened microemulsions even with high content of electrolytes and low pH. We propose that the structure of these microemulsion gels can be described by cross-linking of nano-fine oil droplets via an ABA-triblock copolymer. A new generation of transparent antiperspirant roll-ons with significantly improved skin tolerance can now be formulated as an attractive alternative to alcohol-based products.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2004년도 Proceedings of the second conference of aseanian membrane society
• /
• pp.207-210
• /
• 2004

The pore-filled anion-exchange membranes were prepared in this study with an asymmetric poly(vinylidene fluoride)(PVDF) membrane as a nascent membrane and poly(vinylbenzyl chloride)(PVBCl) as a polyelectrolyte. The solution of PVBCI having the chloromethylate aryl ring of 80 percents and 1,4-diaminobicyclo [2,2,2]octane(DABCO) was made with the solvent of tetrahydrofuran(THF) and N,N-Dimethylformamide(DMF), which is in the rotio of 8:2. A new preparation method in this study, i.e. in-situ crosslinking, enabled us to produce the pore-filled membranes without change of size, and to control the properties of final membrane with various degree of cross-linking. From the result of surface morphologies of SEM and AFM the polyelectrolyte exists in the pores of nascent membrane as a certain configuration. From the investigation of the solvent affecting much to the permeability and rejection, it was found. that the membranes using DMF and THF showed better performances than the membranes produced by THF only. The water permeability of the final membrane at low pressure(100㎪) showed a typical ultrafiltation membrane's permeability (8-10kg/㎡hr) and good values of rejection(55∼60 percent).