• 한국소음진동공학회논문집
• /
• 제26권4호
• /
• pp.420-427
• /
• 2016

Diverse research on gearing systems have been made to resolve gear NVH problems for many decades, and transmission error (T.E.) has been identified as one of the main sources generating gear noises. While gear profiles and amounts of tooth modifications have influences on gear noise in the design aspect, it is found that bad manufacturing conditions such as burrs, bumps and damage, which result in improper gear operating conditions, produce gear noise with respect to manufacturing process. In this paper, T.E. measurement system was introduced to examine the gears damaged or improperly manufactured, while they are assembled, by comparing T.E. values and various gear conditions with theoretical ones. This T.E. measurement system, following grinding machining process, has been installed in a manufacturing line in 2014, and it results that the transmission rework to resolve manufacturing problems is not needed at the end of line.

• 제어로봇시스템학회논문지
• /
• 제19권6호
• /
• pp.508-512
• /
• 2013

In recent years, sensorless drive schemes have been proposed widely and most of them are based on the ZCP (Zero Crossing Point) detection of the BEMF (Back Electro-Motive Force). These schemes have two main problems. One is that ZCP may not be detected at low speed and thus a forced drive is required. The other problem is that there is $30^{\circ}$ phase difference between ZCP and the motor commutation instant and to ensure proper operation, this gap should be accounted for. To solve these problems a circuit is devised for detecting ZCP of the BEMF difference through the line voltage difference. Experimental results show that the output of this circuit is identical to that of the Hall sensor signal, and velocity control of a BLDC motor is possible without the sensor.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2006년도 춘계학술대회 논문집
• /
• pp.481-486
• /
• 2006

In this paper, a new on-line high-voltage motor monitoring system is proposed. This system monitors the insulation condition of the stator winding by on-line measurements of partial discharge (PD). And this system displays magnitude and phase angle distribution of PD. Sensor, CC (Ceramic Coupler) is used for PD measurement. PD signals are continuously measured and digitized with a A/D converter to build the database of the high-voltage motor's insulation condition. Also, this system can communicate with the central monitoring system via RS-232, 422, and TCP/IP. This helps more efficient operation and maintenance of the high-voltage motor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1043-1044
• /
• 2007

The line-start permanent magnet synchronous motor has a high efficiency and an advantage in constant speed operation regardless of the effect of load variation. However it is difficult to predict the performance of characteristics accurately, because of the unbalanced starting torque with the initial starting position of the rotor and the generation of a break torque. In this paper the dynamic characteristics of the line-start permanent magnet synchronous motor are described and compared with those of the squirrel-cage induction motor through the simulation to find the characteristics of the permanent magnets and the rotor bars in the line-start permanent magnet synchronous motor. Finally this paper gives the comparison between the simulation results and the experiment results.

• 정보학연구
• /
• 제7권4호
• /
• pp.61-69
• /
• 2004

본 논문에서는 6.6kV급 고압전동기 모델 코일을 4가지의 권선의 인공적인 결함을 갖도록 제작하였다. 운전중 모의를 위해 모델 코일에 80pF의 에폭시-마이카 커플러를 설치하였으며, TGA를 사용하여 NQN, 부분방전 크기 및 부분방전 패턴 등을 측정하였다. 웨이블렛 변환기법을 이용한 고압전동기의 고정자권선의 결함에서 발생된 부분방전신호의 파형을 통하여 여러 가지의 통계적인 파라메터를 통하여 특징을 추출하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.15-17
• /
• 2002

In this paper, we analyse the dynamic characteristic of 3-phase line start permanent magnet motor considering magnetization. Magnetization vector of NdFeB is obtained from the 2-D FEM magnetization analysis. And comparing the proposed analysis with conventional analysis method, we know that it is necessary to consider magnetization in dynamic analysis.

• Journal of Electrical Engineering and Technology
• /
• 제1권2호
• /
• pp.161-169
• /
• 2006

Load representation has a significant impact on power system analysis and control results. In this paper, composite load models are developed based on on-line measurement data from a practical power system. Three types of static-dynamic load models are derived: general ZIP-induction motor model, Exponential-induction motor model and Z-induction motor model. For the dynamic induction motor model, two different third-order induction motor models are studied. The performances in modeling real and reactive power behaviors by composite load models are compared with other dynamic load models in terms of relative mismatch error. In addition, numerical consideration of ill-conditioned parameters is addressed based on trajectory sensitivity. Numerical studies indicate that the developed composite load models can accurately capture the dynamic behaviors of loads during disturbance.

• Journal of Power Electronics
• /
• 제7권4호
• /
• pp.271-277
• /
• 2007

In this paper, an induction motor rotor fault diagnosis system using current signals, which are measured using the axis-transformation method is presented. Inverter-fed motor drives, unlike line-driven motor drives, have stator currents which are rich in harmonics and therefore fault diagnosis using stator current is not trivial. The current signals for rotor fault diagnosis need precise and high resolution information, which means the diagnosis system demands additional hardware such as a low pass filter, high resolution ADC, an encoder and additional hardware. Therefore, the proposed axis-transformation method is expected to contribute to a low cost fault diagnosis system in inverter-fed motor drives without the need for any additional hardware. In order to confirm the validity of the developed algorithms, various experiments for rotor faults are tested and the line current spectrum of each faulty situation, using the Park transformation, is compared with the results obtained from the FFT(Fast Fourier Transform).

• 제어로봇시스템학회논문지
• /
• 제21권10호
• /
• pp.910-916
• /
• 2015

A sensorless motor control scheme with conventional back-Electro Motive Force (EMF) sensing based on zero crossing point (ZCP) detection has been widely used in various applications. However, there are several problems with the conventional method for effectively driving sensorless brushless motors. For example, a phase mismatch of 30 degrees occurs between the ZCP and commutation time. Additionally, most of the motor speed/current controls are achieved based on a pulse width modulation (PWM) method, which generates significant noise that distracts the back-EMF sensing. Due to the PWM switching, the ZCP is not deterministic, and thus the efficiency of the motor is reduced because the phase transition points become uncertain. Moreover, the motor driving performance is degraded at a low speed range due to the effect of PWM noise. To solve these problems, an improved back-EMF detection method based on a differential line method is proposed in this paper. In addition, the proposed sensorless BLDC driver addresses the problems by using a variable voltage driver generated from a buck converter. The variable voltage driver does not generate the PWM switching noise. Consequently, the proposed sensorless motor driver improves 1) the signal-to-noise ratio of back-EMF, 2) the operation range of a BLDC motor, and 3) the torque characteristics. The proposed sensorless motor driver is verified through simulations and experiments.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.479-482
• /
• 2000

To complite the high speed cutting system, It should be solved some problems, to make light the weight of mechanism for feedrate, develop the Linear motor that bas more power, high speed control system, and high speed cutting tools, nowadays, although many high speed cutting machine is to be built by some machine maker ,they have same problems, in this study, developed the system ball screw type before the feedrate mechanism for linear motor ,so we make the basic system for Line Cents . through that, it is limited to reduce the weight of frame and their frame is to be designed differently each other to reach the purpose special material or strucutre should be contrived.