• Journal of the Korean Applied Science and Technology
• /
• v.27 no.4
• /
• pp.399-406
• /
• 2010

This study was performed to test the flame retardancy of zelkova sarrata-based materials by the treatment of ammonium salts. Zelkova sarrata plate was soaked by the treatment with three 20 wt% ammonium salt solutions consisting ammonium chloride (AMSL), monoammonium phosphate (MAPP), and diammonium phosphate (DAPP), respectively, at the room temperature. After the drying specimen treated with chemicals, combustion properties were examined by the cone calorimeter (ISO 5660-1). When the ammonium salts were used as the retardant for zelkova sarrata, the flame retardancy improved due to the treated ammonium salts in the virgin zelkova sarrata. However the specimen shows increasing CO over virgin zelkova sarrata and It is supposed that toxicities depend on extents. Also, the specimen with ammonium salts showed the higher total smoke release (TSR) than that of virgin plate. Of specimens treated with ammonium salts the ammonium chloride handled the test side was considered a improved inhibitory effect of combustion.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.6
• /
• pp.309-312
• /
• 2006

This study shows to blend ethylene vinyl acetate(EVA) and a flame retardant agent, $Mg(OH)_{2}$, and synergists, zinc borate for improving flame retardancy of low density polyethylene(LDPE). And it studied the property of flame retardancy of LDPE/EVA blend by the amount of addition through LOI and TGA, estimated the electrical characteristics such as volume resistivity and breakdown strength. The flame retardancy of LDPE/EVA blend was much improved in case of adding zinc borate with 6phr degree, and the electrical characteristics were more or less decreased depending on increasing the amount of addition. Zinc borate used for improving the flame retardancy of LDPE/EVA blend let the added amount of a flame retardant agent, $Mg(OH)_{2}$ limited, and the electrical characteristics decreased extremely by adding a good deal of $Mg(OH)_{2}$.

• Journal of the Korean Society of Safety
• /
• v.18 no.2
• /
• pp.56-63
• /
• 2003

Flame retardancy and mechanical properties of recycled polyolefinic plastics/inorganic filler composite systems were investigated by using several inorganic flame retardants such as magnesium hydroxide and slag powder generated electro arc furnace Compatibilizer user each maleic anhydride functionalized polyethylene (PE-g-MAH) and polypropylene(PP-g-MAH) or used mixture of these. The effect of polymeric compatibilizers on the properties of composites was studied by tensile and impact test, differential scanning calorimetry, in the changed fracture mechanism. The improved adhesion was particularly reflected in the mechanical properties. The flame retardancy of composites was examined by measuring limiting oxygen index(LOI, ASTM D2863), smoke density(ASTM D2843) and vertical burning test(UL94). Regarding the flame retardant effect, the EAF slag powder is behaving as synergists as they are only active in the presence of magnesium hydroxide.

• Polymer(Korea)
• /
• v.27 no.6
• /
• pp.569-575
• /
• 2003

The flame retardancy was investigated when the halogenated flame retardant, decabromodiphenyl oxide (DBDPO) and chlorinated paraffin wax (CPW), was added to the polypropylene (PP) / montmorillonite (MMT) nanocomposites. The flame retardancy of polymer resin could be improved not only by addition of flame retardant but also with nanoparticles compositions. The effect of the contents of flame retardant and nanoparticles on the flame retardancy of polypropylene/ montmorillonite nanocomposite systems was thoroughly examined in terms of limited oxygen index (LOI) and cone calorimetry. As a results of cone calorimetry, the heat release rate (HRR) was reduced by the flame retardant DBDPO and CPW, and CPW was a little better than DBDPO. The LOI increased from flammable region (LOI<19) to nonflammable region (LOI>20) for all the flame retardants used in this study. Especially, the improvement in flame retardancy by compounding with PP and MMT was better than that by adding flame retardant to polypropylene. So, the addition of flame retardant after compounding with montmorillonite was more efficient than simple addition of flame retardant.

• Fire Science and Engineering
• /
• v.22 no.3
• /
• pp.300-304
• /
• 2008

The flame retardancy was evaluated to present as the fundamental data to decrease the fire hazard of polymers and life losses according to the addition of clay. The combustion characteristics were examined to increase flame retardancy and to decrease smoke yield of epoxy by the addition of clay such as montmorillonite in this study. For this study, the experiments of flame retardancy were conducted the measurement of the limiting oxygen index (LOI), char yield, and smoke density. As MMT concentration increased, LOI and char yield increased. This result showed that the flame retardancy of epoxy/MMT composite was improved. On the contrary, smoke density increased.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.4
• /
• pp.417-430
• /
• 2020

The flame retardancy, such as carbonized length and area, of four plank type wood products by the spreading concentration and impregnation time of flame retardant were measured according to standard of the Nation Fire Agency in Republic of Korea. To measure the flame retardancy, Korean pine plywood, Japanese larch plywood, Japanese cypress planks, and perforated birch plywood boards were treated with self-development flame retardant by 300 and 500 g/㎡ spreading concentration and those were compared with control specimen. In general, the flame retardant performance of wood products improved as the spreading concentration of flame retardant increased. Except for Japanese larch plywood, there was no significant difference in the flame retardant performance by the spreading concentration. The flame retardant performance of perforated birch plywood board was positively correlated up to 60 minutes of impregnation time, but then gradually decreased. These results about the flame retardancy of wood products by spreading concentration and impregnation time were expected to be basic data for improving flame-retardant treated wood.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.3
• /
• pp.317-327
• /
• 2009

In this study DMT(Dimethylterephthalate), NDC(Dimethyl-2, 6-Naphthalene Dicarboxylate) were used to synthesize polyester polyol which shows enhanced storage stability, improved flame retardancy, and good compressive strength. If DMT and NDC react respectively with DEG(Diethylene Glycol) which is kind of linear diol, the obtained polyester polyols tend to crystallize easily after the reaction. In case of DMT, PA(Phthalic Anhydride) which has asymmetric structure was introduced to retard the crystallization. In case of NDC, DPG(Dipropylene Glycol) which has an methyl side chain was introduced to prevent the crystallization. It was found that to introduce DPG was much more effective method to prevent the crystallization than PA. NDC and DMT were reacted together with DPG for various compositions of NDC:DMT(8:2, 6:4, 4:6 mol ratio). The obtained NDC-DMT-DPG based polyester polyol showed improved flame retardancy, and good compressive strength with increasing the content of NDC.

• Applied Chemistry for Engineering
• /
• v.18 no.3
• /
• pp.251-254
• /
• 2007

Veneer plate was painted by the treatment with ammonium salts such as ammonium chloride (AMCR), ammonium sulfate (AMSF), monoammonium phosphate (MAPP), and diammonium phosphate (DAPP) at room temperature. The flame retardancy of painted veneer plate was investigated. The painted veneer plate shows an increased $CO/CO_2$ over virgin veneer and it was supposed to affect the toxicity to different extents. But when the ammonium salts were used as the retardant for veneer, the flame retardancy was improved due to the painted ammonium salts in the veneers. Also, the veneer plates with ammonium sulfate and ammonium chloride showed both the lower total smoke release (TSR) and lower total smoke production (TSP) than that of virgin veneer.

• Polymer(Korea)
• /
• v.26 no.5
• /
• pp.623-633
• /
• 2002

The flame retardant and thermal properties of ortho-cresol novolac (OCN) and biphenyl epoxy blends containing red-phosphorus were investigated. For five types of compounds designed with the volume ratio of OCN and biphenyl epoxy, thermal properties were analysed by TGA or DTC, and flame retardancy effectiveness was estimated through UL-94V test. While the flame retardant and thermal properties were improved with the content of filler and red-phosphorus, the excessive amount of red-phosphorus caused to deteriorate those properties. Using the blends of OCN/biphenyl rather than pure OCN or biphenyl epoxy as a matrix the flame retardancy of composites could be improved by the synergic effects of high thermal resistance of OCN and intumescent property of biphenyl. The flame retardant me chanism of epoxy compound containing red-phosphorus could be thought of the heat-insulating effect of intumescent char-layer formed in the surface of composites.

• Elastomers and Composites
• /
• v.39 no.2
• /
• pp.105-120
• /
• 2004

The flame retarded NBR foams were prepared with metal hydroxides and various phosphorus/nitrogen-contain ing flame retardants. The dependency of the phosphorus content on thermal properties, flame retardancy, smoke density, and foaming properties were investigated in the foams. Foaming properties and morphology of the flame retarded NBR foams with P/N flame retardants( ${\le}10 phr$) were similar to those of the foams without P/N ones but containing metal hydroxides The flame retardancy of the foams was improved with increasing the phosphorus content and char formation under combustion atmosphere. The cone-calorimeter test and LOI index were also coincided with the TGA analysis quite well. The heat release rate (HRR), total heat release (THR), and effective heat of combustion (EHC) were decreased, whereas the carbon monoxide yield was increased with increase of the phosphorus content of P/N flame retardant. The smoke density values were closely related with CO yield values obtained by the cone-calorimeter test due to the high and hard char formation.