• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.640-644
• /
• 2003

There are many difficulties to get the scattered field generated by obstacle which has arbitrary shape or irregular surface impedance by using analytic solution or numerical methods. In this study, we propose experimental method of acoustic scattering holography that can predict the far-field scattered field based on nearfield measurements. In particular we can get the scattered fields of each wave-number components of incident fields. We express the relationship of wave-number components between incident fields and scattered fields using scattering matrix which is transfer matrix of wave-number components. Lastly, we prove the relation between wave-number components of incident and scattered field by experiments. The errors which are caused by measurements and decomposition methods are also analyzed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.4
• /
• pp.36-41
• /
• 2014

Most faults that occur on transmission lines are caused by extreme weather with lightning storms in the distance. These are not only prolongs the time of removing and recovering, but also increases economical damages. If faults can be precisely located, maintenance crews can reach them quickly, and remove the faults in time. So, the precise locating of the faulted point on a transmission line is very important to improve the system reliability, and decreases economic damages as an inherent consequence of long term outages. Also, fault location methods are becoming of much importance for utilities and research. In this paper, two single-terminal impedance-based fault location techniques will be investigated to show the reliability and evaluated the performance of reactance and Takagi method by using MATHCAD program simulations.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2139-2146
• /
• 2008

This paper presents a numerical algorithm for fault location estimation which used to data from both end of the transmission line. The proposed algorithm is also based on the synchronized voltage and current phasor measured from the PMUs(Phasor Measurement Units) in the time-domain. This paper has separated from two part of with/without shunt capacitance(short/long distance). Most fault was arc one-ground fault which is 75% over [1]. so most study focused with it. In this paper, the numerical algorithm has calculated to distance for ground fault and line-line fault. In this paper, the algorithm is given with/without shunt capacitance using II parameter line model, simple impedance model and estimated using DFT(Discrete Fourier Transform) and the LES(Least Error Squares Method). To verify the validity of the proposed algorithm, the EMTP(Electro- Magnetic Transient Program) and MATLAB did used.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1269-1276
• /
• 2014

The main objective of this paper is to design DC-DC MPPT circuit using chaotic pulse width modulation to track maximum power from solar PV module for space application. The direct control method of tracking is used to extract maximum power. The nominal duty cycle of the main switch of DC-DC SEPIC converter is adjusted so that the solar panel output impedance is equal to the input resistance of the SEPIC converter which results better spectral performance in the tracked voltages when compared to conventional PWM control. The conversion efficiency of the proposed MPPT system is increased when CPWM is used as a control scheme

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.393-399
• /
• 2018

An electrostatic boundary-value problem of a dielectric-wedge-backed, double-slotted conducting wedge is investigated to analyze an asymmetric coplanar waveguide with an infinite dielectric thickness using the Mellin transform and a mode-matching method. Our theoretical solution based on eigenfunction expansion and residue calculus is a rigorous and fast-convergent series form. Numerical computations are conducted to evaluate the potential field, capacitance, and characteristic impedance for various structures of the asymmetric coplanar waveguide. The computed results show good agreement with the simulated results.

• Proceedings of the KIEE Conference
• /
• 2003.11a
• /
• pp.245-247
• /
• 2003

Zone 3 of the distance relay is used to provide the remote back-up protection in case of the failure of the primary protection. However, the risk for mal-operations under stressed conditions such as heavy loading, voltage and transient instability is usually high. Zone 3 is used in combination with the derivatives of the voltage, and current, etc to prevent mal-operations. Sometimes, the impedance characteristics that restrict the tripping area of relay are used to avoid the mal-operations due to load encroachment. This paper presents a novel zone 3 scheme based on combining the steady-state components(i.e. 60Hz) and the transient components(TCs) using a state diagram that visualizes the sequence of studies that emanate from the sequence of events. The simulation results show that the novel zone 3 distance relay elements using the proposed method operates correctly for the various events.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.1
• /
• pp.40-47
• /
• 2017

In this paper, a small signal model for grid-connected inverter with unipolar pulse width modulation method is presented. Small-signal analysis allows to predict the stability and dynamics of the inverter. To regulate output voltage and to achieve power factor correction, inverter has two control loops. Loop gains are useful to identify the stability for multi-loop controlled system. Based on small-signal model, controllers are designed to improve audio susceptibility and output impedance characteristics. Proposed small-signal model and controllers are verified by PSIM simulation and experiments.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.83-84
• /
• 2015

본 논문에서는 무효전력 오차를 야기하는 유도성-저항성 복합성의 불평형 임피던스 선로 하에서 가상 인덕터와 가상 저항을 사용한 드룹 제어 기반의 병렬형 인버터 시스템에 관해 다루고 있다. 여기서 무효 전력 분담 에러는 각 선로 임피던스의 전압 강하를 고려함에 따라 개선 가능하다. 그러나 병렬형 인버터 시스템이 고전류, 고용량일 경우 지령 출력 전압 크기는 정격 전압 크기에 미치지 못하게 되며 이는 가상 인덕터 및 저항값과 출력 전류의 곱을 통한 가상 임피던스의 전압강하 산출법에 기인한다. 이러한 이유로 본 논문에서는 기존의 드룹 방식에 선로 임피던스 전압 강하 뿐만 아니라 가상 임피던스의 전압 강하도 추가되었고 이를 통해 병렬형 인버터의 전압 출력이 정격 출력값의 범위 안에서 구동하도록 하였다. 가상 인덕터와 가상 저항의 적용법에 대한 비교에 기반을 둔 제안된 드룹 방식은 PSIM 시뮬레이션을 통해 검증되었다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.317-322
• /
• 2004

In this paper, It was describe the processes of development of HiFi speaker system. Woofer and tweeter were fabricated by unskilled students and their 1.5 parameters were identified by known mass method. Based on T-S parameters port enclosure was designed and built by means of software. Acoustic radiation phenomena of port enclosure were simulated and compared to test result. Acoustic pressure difference between lower frequency and higher frequency was flattened by adopting optimal crossover network. Finally, built HiFi speaker system was showed good sound quality and sound pressure and electrical impedance was well agreed with test results each other.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.34 no.1
• /
• pp.1-5
• /
• 1998

This study presents intelligent deburring system which can transfer the exper's skill to deburring robot through neural network. The expert's skill is expressed as associate mapping between the characteristics of the burr and human expert's action. Under the fundamental idea that the state of the deburring process can be extracted via the visual sense of the human, we employ vision system for the perception and identification of the changing burr. From the demonstration of human experts, force data are measured and fitted impedance model. Finally the characteristics of the burr and coressponding force are associated by the neural network which is trained through many demonstrations. The proposed method is verified in the deburring process of welding burr.