• Journal of Electrical Engineering and Technology
• /
• 제12권3호
• /
• pp.1203-1210
• /
• 2017

Switched-inductor (SL) Z-source three-level inverter is a novel high power topology. The SL based impedance network can boost the input dc voltage to a higher value than the single LC impedance network. However, as all the neutral-point-clamped (NPC) inverters, the SL Z-source three-level inverter has to balance the neutral-point (NP) potential too. The principle of the inverter is introduced and then the effects of NP potential unbalance are analyzed. A NP balancing method is proposed. Other than the methods for conventional NPC inverter without Z-source impedance network, the upper and lower shoot-through durations are corrected by the feedforward compensation factors. With the proposed method, the NP potential is balanced and the voltage boosting ability of the Z-source network is not affected obviously. Simulations are conducted to verify the proposed method.

• 전기학회논문지
• /
• 제68권2호
• /
• pp.304-309
• /
• 2019

This paper presents a CMOS RF-to-DC converter for video surveillance disposable IoT applications. It widely harvests RF energy of 3G/4G cellular low-band frequency range by employing a tunable impedance matching network. The proposed converter consists of the differential-drive cross-coupled rectifier and the matching network with a 4-bit capacitor array. The proposed converter is designed using 130-nm standard CMOS process. The designed energy harvester can rectify the RF signals from 700 MHz to 900 MHz. It has a peak RF-to-DC conversion efficiency of 72.25%, 64.97%, and 66.28% at 700 MHz, 800 MHz, and 900 MHz with a load resistance of 10kΩ, respectively.

• 대한전자공학회논문지
• /
• 제12권4호
• /
• pp.41-45
• /
• 1975

기계계와 전기계 사이의 두 analogy로부터 mobility 회로와 impedamice회로를 얻었다. 이 두 기계기로에서 Ipedance와 nobility관계를 회로망리론을 근거로 비교 검토 하였고 이로부터 mobility 회로가 더 자연스럽고 기본적인 기계회로임을 구명하였다. 또한 impedance측정이 관찰점과 수에 따라서 가변성인데 비하여 mobility 측정은 불변성임을 보였다. Two mechanical networks, mobility network, and impedance network, are proposed md the relations between a mechanical system n4 their two mechanical networks are examined briefly. The mobility network is founed to be more natural of two networks. This paper also shows the invariant property of mobility elements in the measurement procedure.

• 한국음향학회지
• /
• 제20권5호
• /
• pp.69-75
• /
• 2001

본 연구에서는 일반적인 1, 2단자쌍 회로망의 임피던스 정합회로를 간단하고 빠르게 구할수 있는 새로운 방법을 제시하였다. 먼저 임피던스 정합 대상인 1단자쌍 또는 2단자쌍 회로망에 인덕터와 캐패시터의 조합으로 이루어진 임의의 L-회로망 형태의 정합회로가 포함된 전체 회로망 구조를 설정하고, 이 구조에 대한 전송행렬을 계산한 뒤에 회로망 양단의 부하저항 조건을 적용하여 전체 회로망의 입출력 임피던스를 구하였다. 이 식으로부터 정합용 소자의 정확한 값을 연립방정식을 이용하여 계산하였다. 본 연구의 타당성을 검증하기 위해 CDMA(code division multiple access)용 소자로 널리 사용되는 중간주파수 대 역 withdrawal 가중형 SAW필터 에 본 연구에서 제시한 방법을 적용하여 임피던스 정합 전후의 특성변화를 시뮬레이션과 실험을 통하여 확인하였다. 그 결과 85.38 MHz의 중심주파수에서 비대역폭이 1.2％ 삽입손실이 29 dB, VSWR (voltage standing wave ratio)이 80인 필터를 본 연구방법을 이용하여 정합한 경우에 각각의 성능이 1.8％, 9 dB, 3으로 향상됨을 시뮬레이션과 실험을 통해 확인하였다. 본 연구결과는 SAW (surface acoustic wave) 디바이스의 정합에 매우 용이하게 이용될 수 있을 뿐만 아니라 다른 형태의 1, 2단자쌍 회로망의 임피던스 정합에도 널리 사용될 수 있다.

• 한국전자파학회논문지
• /
• 제23권3호
• /
• pp.367-376
• /
• 2012

본 논문에서는 물리적인 환경 변화에 의해 발생될 수 있는 갑작스런 부하단 임피던스의 변화에 능동적으로 대응할 수 있는 적응형 임피던스 정합 회로를 구성하는 부정합 측정부, 임피던스 정합부, 조정 알고리즘부의 특성과 현재까지 진행된 연구 수준을 확인해 보았고, ${\lambda}/4$ 전송 선로와 ${\pi}$-네트워크를 이용하여 간단히 구성된 적응형 임피던스 정합 회로의 설계 결과를 보였다. 이를 위해 간단한 구성을 가지면서 반복적인 계산없이 임의의 부하단 임피던스를 바로 제어할 수 있는 적응형 임피던스 정합 회로를 제안하였고, 설계를 위한 계산식을 유도하였다. 또한, 유도된 계산식을 통해 최적화된 임피던스를 찾아주어 능동적으로 제어할 수 있는 조정 알고리즘도 제시하였다. 제안한 적응형 임피던스 정합 회로에서 유도된 계산식과 조정 알고리즘을 이용하여 시뮬레이션을 수행하였고, 시뮬레이션 결과 임의의 부하단 임피던스가 회로에 최적화된 임피던스로 능동적으로 제어 될 수 있음을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 B
• /
• pp.856-858
• /
• 1999

The analysis of distribution line faults is essential to the proper protection of power system. A high impedance fault(HIF) dose not make enough current to cause conventional protective device. It is well known that undesirable operating conditions and certain types of faults on electric distribution feeders cannot be detected by using conventional Protection system. This paper describes an algorithm using neural network for pattern recognition and detection of high impedance faults. Wavelet transform analysis gives the time-scale information. Time-scale representation of high impedance faults can detect easily and localize correctly the fault waveform.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.118-121
• /
• 2003

In the conventional boundary estimation in EIT (Electrical Impedance Tomography), the interface between anomalies and background is expressed in usual as Fourier series and the boundary is reconstructed by obtaining the Fourier coefficients. This paper proposes a method for the boundary estimation, where the boundary of anomaly is approximated as the interpolation of front points located discretely along the boundary and is imaged by tracking the points in the region of interest. In the solution to the inverse problem to estimate the front points, the multi-layer neural network is introduced. For the verification of the proposed method, numerical experiments are conducted and the results indicate a good performance.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.40-45
• /
• 2004

This work presents a boundary estimation approach in electrical impedance imaging for binary-mixture fields based on a parallel structured multi-layer neural network. The interfacial boundaries are expressed with the truncated Fourier series and the unknown Fourier coefficients are estimated with the parallel structure of multi-layer neural network. Results from numerical experiments shows that the proposed approach is insensitive to the measurement noise and has a strong possibility in the visualization of binary mixtures for a real time monitoring.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 추계학술대회
• /
• pp.223-224
• /
• 2011

This paper presents the method to design the inductor and capacitor value considering the ripple component that may be generated by three operating states of the Quasi Z source inverter at the impedance network. Based on the analysis of each operation mode, the equations of the capacitor voltage and inductor current are derived. In order to simplify the design processing, design equations of the impedance network are derived where the capacitor voltage and inductor current are lineared. The validity of the design method is verified with the simulation result using PSIM.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 추계학술대회
• /
• pp.111-112
• /
• 2017

This paper presents a novel three-port converter for the OnBoard Charger of Electric Vehicles by using an impedance control network. The proposed concept is suitable for charging a main battery and an auxiliary battery of an electric vehicle at the same time due to its power handling capability of the converter without additional switches. The power flow is managed by the phase angle (${\Theta}$) between the ports whereas voltage at each port is controlled by the asymmetric duty cycle and the phase shift (${\Phi}$) between the inverter lags controlled by the impedance control network. The proposed system has a capability of achieving zero voltage switching (ZVS) and zero current switching (ZCS) at all the switches over the wide range of input voltage, output voltage and output power. The feasibility of the proposed system is verified by the PSIM simulation.