• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.3
• /
• pp.341-348
• /
• 2019

In this paper, a monopole type antenna applicable to WLAN and WiMAX standard frequency bands is designed and fabricated. The proposed antenna is designed to have rectangular ring and rectangular patch based on microstrip feeding for triple band characteristics and inserted two stub in the top of the rectangular ring patch to enhance impedance bandwidth characteristics. The proposed antenna has $18.0mm(2W_1+W_2){\times}33.0mm(L_7+L_8+L_9)$ on a dielectric substrate of $27.0mm(W_1){\times}44mm(L_1){\times}1.0mm$ size. From the fabrication and measurement results, impedance bandwidths of 660MHz (2,08 to 2.74GHz) for 2.4/2.5MHz band, 488MHz (3.40 to 3.88GHz) for 3.5MHz band, and 2,180MHz (4.61 to 6.79GHz) for 5,000MHz band were obtained based on the impedance bandwidth. The proposed antenna also obtained the measured gain and radiation pattern in the anechoic chamber.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.644-652
• /
• 2004

In this paper, we designed a cascaded microstrip lowpass filter using the lowpass filters previously proposed. The previously proposed lowpass filters have a ultra-wide stopband and prominent cutoff sharpness using the combined characteristics of slot and microstrip open stub, respectively, and they are catagorized into 2 types by the method that determining their passband characteristics. The first type is determined its passband characteristics by open stub characteristics and the second is by slot characteristics. By cascading these structures with impedance adjustment of each element, the deeper out-of-band rejection and the sharper skirt response were achieved. The fabricated cascaded lowpass filters have -3㏈ cutoff frequencies at 1.035㎓ and 1.286㎓ respectively and -20㏈ stopband is over 20㎓ for both structures.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2024-2030
• /
• 2003

Design for a quite operation of fluid power system requires the understanding of noise and vibration characteristics of the system. This paper presents a dynamic response for design of hydraulic circuit. Experimental investigations on the attenuation characteristics of pressure ripple in automotive power steering hydraulic pipe with dynamic response of hydraulic pipe line is examined. Also, a mathematical model of hydraulic pipe is proposed to support design of the hydraulic circuit and analyze the attenuation characteristics of pressure ripples in a hydraulic pipe line. And analyze the impedance characteristics to determine the postion to construct accumulator for attenuation the pressure pulsation. The experimental results show that the pulsation attenuation characteristics of hydraulic hoses is remarkably affected by the flexible metal tube inserted coaxially inside a hydraulic hose with a finite length as well as viscoelastic properties of hose wall. It is also shown that the predicted results by the model proposed here agree well with the measured results over a wied range of frequency;

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.223-225
• /
• 2005

An external electrode fluorescent lamps (EEFLs) have the advantage of a long lifetime in the early stages of the study on plasma discharge, interest in the lamp continues. Studies on the operation of external electrode fluorescent lamps have focused mainly on its use of a type of high frequency (MHz). By performing high brightness using a square wave operation method with the low frequency below 100kHz, which is applied to a narrowed tube type lamp that has several mm of lamp diameter, an EEFL presented the possibility of using it as a light source for backlights. However, because an EEFL generates plasma using wall charges, which considers the impedance characteristics of glass based on the structural principle in discharge, it can be significantly affected by frequency. Thus, this study verifies the change in the characteristics of electromagnetic fields according to the change in frequency through a Maxwell's electromagnetic field simulation and examines the relationship between the change in the EEFL frequency and brightness by measuring the optical characteristics. In addition, the characteristics of the transformation of energy orbits were verified by investigating the characteristics of the wavelength according to the change in frequency through the OES.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.42-47
• /
• 2008

In this paper, the fault current limiting characteristics for the superconducting fault current limiter(SFCL) using magnetic coupling between two coils were investigated. The SFCL consists of a high-$T_c$ superconducting(HTSC) element and two coils. This SFCL has different characteristics that depend on the connection form, the winding direction and the inductance ratio of two coils. The impedance and the operational current of the SFCL can be adjusted higher or lower than the resistance and the critical current of HTSC element. Therefore, the SFCL can change the amplitude of the limited fault current. To confirm it, the HTSC element was modeled and the fault current limiting characteristics of the SFCL were analysed through computer simulation. It was obtained from the analysis that the connection form and the winding direction of two coils of the SFCL were the important design parameters.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.628-634
• /
• 2005

From AC analysis results utilizing a 2-dimensional device simulator, we extracted an AC-equivalent circuit of a grounded-gate NMOS (ggNMOS) electrostatic discharge (ESD) protection device. The extracted equivalent circuit is utilized to analyze the effects of the parasitics in a ggNMOS protection device on the characteristics of a low noise amplifier (LNA). We have shown that the effects of the parasitics can appear exaggerated for an impedance matching aspect and that the noise contribution of the parasitic resistances cannot be counted if the ggNMOS protection device is modeled by a single capacitor, as in prior publications. We have confirmed that the major changes in the characteristics of an LNA when connecting an NMOS protection device at the input are reduction of the power gain and degradation of the noise performance. We have also shown that the performance degradation worsens as the substrate resistance is reduced, which could not be detected if a single capacitor model is used.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.4 no.1
• /
• pp.13-21
• /
• 1967

A low pass filter is synthesized with R, C and negative impedance converters(NIC). The filter has a 4-th order elliptic function, which gives best magnitude approximation with equi-ripple characteristics both in pass and stop band. And experimental investigations have been made on the effect of the anticipated deviation of the NIC conversion factor and of possible loaded operation. Through the study, it has been cocluded that: 1. For minimum pole-zero sensitivity with respect to the NIC conversion factor, the network of a parallel RC-NIC configuration is preferable and the Horowitz polynomial decomposition method is applied in the synthesis procedure. 2. A few percentage variation of the NIC conversion factor changes the frequency and amplitude characteristics of the filter by nearly negligible amount. 3. With a load resistance below the critical value, the filter turns into an oscillator.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.182-189
• /
• 2004

The application of adhesively bonded components is increasing in various industries such as automobile, aircraft, IC packages, and soldering techniques. In spite of such wide application in adhesively bonded components, nondestructive test techniques applying to adhesively bonded components have not been clearly established yet. In this paper, characteristics of ultrasonic test on interfaces of adhesively bonded components have been investigated by calculating transmission coefficient theoretically and experimentally. From the experimental results, the optimum conditions to establish frequencies for adhesively bonded homogeneous and dissimilar components are 4∼6 MHz and 2∼4 MHz, respectively.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1095-1097
• /
• 1995

We studied on Solide Oxide Fuel cells, have some advantages of higher power density and less cost for power-supply. Recently, Ni-YSZ materials are used as anode of SOFC. If its contents of Ni is higher then its electronic conductivity is higher. And If it has inverse tendency then its ionic conductivity become higher. So in this experiments, we investicated the optimum content of Ni, by testing expansion coefficient, impedance characteristics, overvoltage.

• Journal of Power Electronics
• /
• v.14 no.1
• /
• pp.143-155
• /
• 2014

The stability issues of a multi-module distributed DC power system without current-sharing loop are analyzed in this study. The physical understanding of the terminal characteristics of each sub-module is focused on. All the modules are divided into two groups based on the different terminal property types, namely, impedance (Z) and admittance (Y) types. The equivalent circuits of each group are established to analyze the stability issues, and the mathematical equations of the equivalent circuits are derived. A generalized criterion for multi-module distributed systems is proposed based on the stability criterion in a cascade system. The proposed criterion is independent of the power flow direction.